Assuring reclaimed water quality using a multi-barrier treatment train according to the new EU non-potable water reuse regulation.

In this study, we evaluated the ability of various pilot-scale treatment train combinations to meet the microbial requirements of the new European non-potable water reuse regulation 2020/741. The study utilized non-disinfected secondary effluent from the wastewater treatment plant in Schweinfurt, Germany, as feedwater for two pilot-scale treatment trains. The first, a reference treatment train (Train A), consisted of filtration and UV disinfection as specified for reclaimed water class A in the EU regulation. The second, an advanced treatment train (Train B), included ceramic ultrafiltration (UF), ozonation, biological activated carbon filtration (BAC), and final UV disinfection. Based on a Monte Carlo simulation for Train A, the EU requirements for pathogen removal were not met when an average UV dose of 400-600 J m-2 was applied. This shortcoming was likely due to a moderate transmittance range (50-65 %), resulting in decreased UV fluence. These findings suggest that operational conditions for disinfection should be more clearly specified to ensure consistent pathogen inactivation both during validation and regular operation. In contrast, treatment train B successfully met the requirements of the EU regulations by reducing pathogens to below the detection limit. The UF membrane demonstrated a positive effect on the overall log reduction values (LRVs) throughout the water reclamation system. It also enhanced the efficiency of downstream processes, such as ozonation and UV disinfection, by lowering total suspended solids and turbidity. However, even without the UF membrane, treatment train B was still able to meet the pathogenic EU requirements for non-potable reuse applications. Furthermore, the study observed that the inclusion of biologically activated carbon (BAC) filtration requires a final disinfection step (e.g., UV disinfection) to prevent the potential occurrence of heterotrophic bacteria that proliferate in the BAC filter. For process validation it is recommended to use at least two different virus surrogates (MS2 and PhiX174), rather than just one or total coliphage as required in the EU regulation.

Imaging Diffractometric Biosensors for Label-Free, Multi-Molecular Interaction Analysis.

Biosensors are used for the specific and sensitive detection of biomolecules. In conventional approaches, the suspected target molecules are bound to selected capture molecules and successful binding is indicated by additional labelling to enable optical readout. This labelling requires additional processing steps tailored to the application. While numerous label-free interaction assays exist, they often compromise on detection characteristics. In this context, we introduce a novel diffractometric biosensor, comprising a diffractive biosensor chip and an associated optical reader assembly. This innovative system can capture an entire assay, detecting various types of molecules in a label-free manner and present the results within in a single, comprehensive image. The applicability of the biosensor is assessed for the detection of viral DNA as well as proteins directly in human plasma, investigating different antigens. In our experiments, we achieve a detection limit of 4.2 pg/mm², which is comparable to other label-free optical biosensors. The simplicity and robustness of the method make it a compelling option for advancing biosensing technologies. This work contributes to the development of an imaging diffractometric biosensor with the potential for multiple applications in molecular interaction analysis.

Negligible adsorption and toxicity of microplastic fibers in disinfected secondary effluents.

Wastewater treatment plants play a crucial role in controlling the transport of pollutants to the environment and often discharge persistent contaminants such as synthetic microplastic fibers (MFs) to the ecosystem. In this study, we examined the fate and toxicity of polyethylene terephthalate (PET) MFs fabricated from commercial cloth in post-disinfection secondary effluents by employing conditions that closely mimic disinfection processes applied in wastewater treatment plants. Challenging conventional assumptions, this study illustrated that oxidative treatment by chlorination and ozonation incurred no significant modification to the surface morphology of the MFs. Additionally, experimental results demonstrated that both pristine and oxidized MFs have minimal adsorption potential towards contaminants of emerging concern in both effluents and alkaline water. The limited adsorption was attributed to the inert nature of MFs and low surface area to volume ratio. Slight adsorption was observed for sotalol, sulfamethoxazole, and thiabendazole in alkaline water, where the governing adsorption interactions were suggested to be hydrogen bonding and electrostatic forces. Acute exposure experiments on human cells revealed no immediate toxicity; however, the chronic and long-term consequences of the exposure should be further investigated. Overall, despite the concern associated with MFs pollution, this work demonstrates the overall indifference of MFs in WWTP (i.e., minor effects of disinfection on MFs surface properties and limited adsorption potential toward a mix of trace organic pollutants), which does not change their acute toxicity toward living forms.

Exploring the Reconfigurable Memory Effect in Electroforming-Free YMnO3-Based Resistive Switches: Towards a Tunable Frequency Response.

Memristors, since their inception, have demonstrated remarkable characteristics, notably the exceptional reconfigurability of their memory. This study delves into electroforming-free YMnO3 (YMO)-based resistive switches, emphasizing the reconfigurable memory effect in multiferroic YMO thin films with metallically conducting electrodes and their pivotal role in achieving adaptable frequency responses in impedance circuits consisting of reconfigurable YMO-based resistive switches and no reconfigurable passive elements, e.g., inductors and capacitors. The multiferroic YMO possesses a network of charged domain walls which can be reconfigured by a time-dependent voltage applied between the metallically conducting electrodes. Through experimental demonstrations, this study scrutinizes the impedance response not only for individual switch devices but also for impedance circuitry based on YMO resistive switches in both low- and high-resistance states, interfacing with capacitors and inductors in parallel and series configurations. Scrutinized Nyquist plots visually capture the intricate dynamics of impedance circuitry, revealing the potential of electroforming-free YMO resistive switches in finely tuning frequency responses within impedance circuits. This adaptability, rooted in the unique properties of YMO, signifies a paradigm shift heralding the advent of advanced and flexible electronic technologies.

Advanced oxidation processes for water and wastewater treatment - Guidance for systematic future research.

Advanced oxidation processes (AOPs) are a growing research field with a large variety of different process variants and materials being tested at laboratory scale. However, despite extensive research in recent years and decades, many variants have not been transitioned to pilot- and full-scale operation. One major concern are the inconsistent experimental approaches applied across different studies that impede identification, comparison, and upscaling of the most promising AOPs. The aim of this tutorial review is to streamline future studies on the development of new solutions and materials for advanced oxidation by providing guidance for comparable and scalable oxidation experiments. We discuss recent developments in catalytic, ozone-based, radiation-driven, and other AOPs, and outline future perspectives and research needs. Since standardized experimental procedures are not available for most AOPs, we propose basic rules and key parameters for lab-scale evaluation of new AOPs including selection of suitable probe compounds and scavengers for the measurement of (major) reactive species. A two-phase approach to assess new AOP concepts is proposed, consisting of (i) basic research and proof-of-concept (technology readiness levels (TRL) 1-3), followed by (ii) process development in the intended water matrix including a cost comparison with an established process, applying comparable and scalable parameters such as UV fluence or ozone consumption (TRL 3-5). Subsequent demonstration of the new process (TRL 6-7) is briefly discussed, too. Finally, we highlight important research tools for a thorough mechanistic process evaluation and risk assessment including screening for transformation products that should be based on chemical logic and combined with complementary tools (mass balance, chemical calculations).

Assessing the Chemical-Free Oxidation of Trace Organic Chemicals by VUV/UV as an Alternative to Conventional UV/H2O2.

Low-pressure mercury lamps with high-purity quartz can emit both vacuum-UV (VUV, 185 nm) and UV (254 nm) and are commercially available and promising for eliminating recalcitrant organic pollutants. The feasibility of VUV/UV as a chemical-free oxidation process was verified and quantitatively assessed by the concept of H2O2 equivalence (EQH2O2), at which UV/H2O2 showed the same performance as VUV/UV for the degradation of trace organic contaminants (TOrCs). Although VUV showed superior H2O activation and oxidation performance, its performance highly varied as a function of light path length (Lp) in water, while that of UV/H2O2 proportionally decreased with decreasing H2O2 dose regardless of Lp. On increasing Lp from 1.0 to 3.0 cm, the EQH2O2 of VUV/UV decreased from 0.81 to 0.22 mM H2O2. Chloride and nitrate hardly influenced UV/H2O2, but they dramatically inhibited VUV/UV. The competitive absorbance of VUV by chloride and nitrate was verified as the main reason. The inhibitory effect was partially compensated by •OH formation from the propagation reactions of chloride or nitrate VUV photolysis, which was verified by kinetic modeling in Kintecus. In water with an Lp of 2.0 cm, the EQH2O2 of VUV/UV decreased from 0.43 to 0.17 mM (60.8% decrease) on increasing the chloride concentration from 0 to 15 mM and to 0.20 mM (53.5% decrease) at 4 mM nitrate. The results of this study provide a comprehensive understanding of VUV/UV oxidation in comparison to UV/H2O2, which underscores the suitability and efficiency of chemical-free oxidation with VUV/UV.

OrbiFragsNets. A tool for automatic annotation of orbitrap MS2 spectra using networks grade as selection criteria.

We introduce OrbiFragsNets, a tool for automatic annotation of MS2 spectra generated by Orbitrap instruments, as well as the concepts of chemical consistency and fragments networks. OrbiFragsNets takes advantage of the specific confidence interval for each peak in every MS2 spectrum, which is an unclear idea across the high-resolution mass spectrometry literature. The spectrum annotations are expressed as fragments networks, a set of networks with the possible combinations of annotations for the fragments. The model behind OrbiFragsNets is briefly described here and explained in detail in the constantly updated manual available in the GitHub repository. This new approach in MS2 spectrum de novo automatic annotation proved to perform as good as well established tools such as RMassBank and SIRIUS.•A new approach on automatic annotation of Orbitrap MS2 spectra is introduced.•Possible spectrum annotation are described as independent consistent networks, with annotations for each fragment as nodes, and annotations for the mass difference between fragments as edges.•Annotation process is described as the selection of the most connected fragments network.

Ozonation of Gabapentin in Water─Investigating Reaction Kinetics and Transformation Mechanisms of a Primary Amine Using Isotopically Labeled Ozone.

Aliphatic amines are abundant micropollutants in wastewater treatment plant effluents. In order to mitigate such micropollutants, ozonation is one of the most commonly employed advanced treatment processes. Current research regarding ozone efficiency is heavily focusing on reaction mechanisms of different contaminant groups, including structures with amine moieties as reactive sites. This study analyzes pH-dependent reaction kinetics and pathways of gabapentin (GBP), an aliphatic primary amine with an additional carboxylic acid group. The transformation pathway was elucidated applying a novel approach using isotopically labeled ozone (18O) and quantum chemistry calculations. While the direct reaction of GBP with ozone is highly pH-dependent and slow at pH 7 (13.7 M-1 s-1), the rate constant of the deprotonated species (1.76 × 105 M-1 s-1) is comparable to those of other amine compounds. Pathway analysis based on LC-MS/MS measurements revealed that ozonation of GBP leads to the formation of a carboxylic acid group and simultaneous nitrate formation, which was also observed in the case of the aliphatic amino acid glycine. Nitrate was formed with a yield of approximately 100%. Experiments with 18O-labeled ozone demonstrated that the intermediate aldehyde does most likely not include any oxygen originating from ozone. Furthermore, quantum chemistry calculations did not provide an explanation for the C-N scission during GBP ozonation without ozone involvement, although this reaction was slightly more favorable than for respective glycine and ethylamine reactions. Overall, this study contributes to a deeper understanding of reaction mechanisms of aliphatic primary amines during wastewater ozonation.

Gas Transport Mechanisms through Molecular Thin Carbon Nanomembranes.

Molecular thin carbon nanomembranes (CNMs) synthesized by electron irradiation induced cross-linking of aromatic self-assembled monolayers (SAMs) are promising 2D materials for the next generation of filtration technologies. Their unique properties including ultimately low thickness of ≈1 nm, sub-nanometer porosity, mechanical and chemical stability are attractive for the development of innovative filters with low energy consumption, improved selectivity, and robustness. However, the permeation mechanisms through CNMs resulting in, e.g., an ≈1000 times higher fluxes of water in comparison to helium have not been yet understood. Here, a study of the permeation of He, Ne, D2 , CO2 , Ar, O2 and D2 O using mass spectrometry in the temperature range from room temperature to ≈120 °C is studied. As a model system, CNMs made from [1″,4',1',1]-terphenyl-4-thiol SAMs are investigated. It is found out that all studied gases experience an activation energy barrier upon the permeation which scales with their kinetic diameters. Moreover, their permeation rates are dependent on the adsorption on the nanomembrane surface. These findings enable to rationalize the permeation mechanisms and establish a model, which paves the way toward the rational design not only of CNMs but also of other organic and inorganic 2D materials for energy-efficient and highly selective filtration applications.

Advanced oxidation processes for removal of monocyclic aromatic hydrocarbon from water: Effects of O3/H2O2 and UV/H2O2 treatment on product formation and biological post-treatment.

Several oxidative treatment technologies, such as ozonation or Fenton reaction, have been studied and applied to remove monocyclic hydroaromatic carbon from water. Despite decades of application, little seems to be known about formation of transformation products while employing different ozone- or ∙OH-based treatment methods and their fate in biodegradation. In this study, we demonstrate that O3/H2O2 treatment of benzene, toluene, ethylbenzene (BTE), and benzoic acid (BA) leads to less hydroxylated aromatic transformation products compared to UV/H2O2 as reference system - this at a similar ∙OH exposure and parent compound removal efficiency. Aerobic biodegradation tests after oxidation of 0.15 mM BA (12.6 mg C L-1 theoretical DOC) revealed that a less biodegradable DOC fraction > 4 mg C L-1 was formed in both oxidative treatments compared to the BA control. No advantage of ozonation over UV/H2O2 treatment was observed in terms of mineralization capabilities, however, we detected less transformation products after oxidation and biodegradation using high-resolution mass spectrometry. Biodegradation of BA that was not oxidized was more complete with minimal organic residual. Overall, the study provides new insights into the oxidation of monocyclic aromatics and raises questions regarding the biodegradability of oxidation products, which is relevant for several treatment applications.

Isotopically labeled ozone: A new approach to elucidate the formation of ozonation products.

As ozonation becomes a widespread treatment for removal of chemicals of emerging concern from wastewater treatment plant effluents, there are increasing concerns regarding the formation of ozonation products (OPs), and their possible impacts on the aquatic environment and eventually human health. In this study, a novel method was developed that utilizes heavy oxygen (18O2) for the production of heavy ozone ([18O1]O2, [18O2]O1, [18O3]) to actively label OPs from oxygen transfer reactions. To establish and validate this new approach, venlafaxine with a well-described oxygen transfer reaction (tertiary amine -> N-oxide) was chosen as a model compound. Observed 18O/16O ratios in the major OP venlafaxine N-oxide (NOV) correlated with expected 18O purities based on tracer experiments. These results confirmed the successful labeling with heavy oxygen and furthermore demonstrate the potential to monitor NOV as an indicator of 18O/16O ratios during ozonation. As a next step, 18O/16O ratios were used to elucidate the formation mechanism of previously described OPs from sulfamethoxazole (SMX). Seven OPs were detected including the frequently described nitro-SMX, which was formed with a maximum yield of 3.2% (of initial SMX). With the successful labeling of six of the seven OPs from sulfamethoxazole, it was possible to confirm their previously proposed formation pathways, and to distinguish oxygen transfer from electron transfer reactions. 18O/16O ratios in OPs indicate that hydroxylation of the aromatic ring and formation of nitro-groups mostly follows oxygen transfer reactions, while electron transfer reactions initiate the formation of hydroxylamine and the abstraction of NH2 leading to catechol.

Smart Error Sum Based on Hybrid Two-Trace Two-Dimensional (2T2D) Correlation Analysis.

Based on hybrid 2D correlation analysis, we recently derived and introduced a "smart error sum," a sophisticated loss function that can be used for solving nonlinear inverse problems like the determination of optical constants and oscillator parameters from a series of optical spectra in the infrared spectral region. The advantage of the smart error sum compared to the conventional sum of squared errors lies in its ability to marginalize multiplicative systematic errors such as, for example, reflectance values above unity in transflection spectra. This is enabled by a transformation, which allows fits to not exclusively focus on forcing fit spectra to agree with experimental spectra at every wavenumber point by all means, but also to take correlations such as spectral similarities and their changes with certain perturbations into account. In this work, we extend our approach to accommodate the treatment of individual spectra, instead of only series, based on hybrid two-trace two-dimensional (2T2D) correlation analysis. We evaluate and prove the value of our approach by individually analyzing experimental transflection spectra of polymethyl methacrylate (PMMA) layers on gold substrates. The comparison of the results with those obtained by the original smart error sum based on the whole set of spectra as well as those resulting from conventional fitting of series and individual spectra (using the conventional sum of squared errors) confirms the validity and soundness of the 2T2D smart error sum.

Roles of radical species in vacuum-UV/UV/peroxydisulfate advanced oxidation processes and contributions of the species to contaminant degradation at different water depths.

Vacuum-UV (VUV) (wavelength 185 nm)/ UV (wavelength 254 nm) are applied to improve performances of UV-based advanced oxidation processes. However, the improvements were strongly affected by water depth because of poor VUV transmittance in water. In this study, VUV/UV and peroxydisulfate (PDS) were used to degrade carbamazepine. More SO4•- oxidation occurred in VUV/UV/PDS than VUV/UV with similar •OH oxidation occurring. The additional SO4•- oxidation could be caused by VUV/PDS in superficial water or UV/PDS in deeper water. The synergistic factor for VUV/UV/PDS processes relative to VUV/UV and UV/PDS processes was 1.32. VUV/UV/PDS performances were affected by competition for photon absorption by dissolved organic matter (32-58 % inhibition), radical quenching by CO32-/HCO3- and NO3-, and conversion of •OH and SO4•- into reactive chlorine species by Cl-. Radical probe experiments and steady-state kinetic modeling simulations indicated that 34 %, 25 %, and 40 % of carbamazepine degradation occurring in 2-cm-deep bulk solution was due to •OH oxidation through VUV/H2O, SO4•- oxidation through VUV/PDS, and SO4•- oxidation through UV/PDS, respectively. Contribution of VUV-driven processes decreased with increasing water depth and became equivalent to contribution of 3.5-cm-deep UV-driven processes, which indicated the importance of optimizing water depth in VUV/UV-advanced oxidation process reactors.

Stable isotope labeling for detection of ozonation byproducts in effluent organic matter with FT-ICR-MS.

Despite effluent organic matter (EfOM) being a major consumer of ozone during wastewater treatment, little is known about ozonation byproducts (OBPs) produced from EfOM. To unambiguously identify OBPs, heavy ozone was used to ozonate EfOM, resulting in 18O labeled and unlabeled OBPs. Labeled OBPs mostly represent a single 18O transfer and were classified as either direct or indirect OBPs based on the 18O/16O intensity ratios of the isotopologues. Of the 929 labeled OBPs, 84 were unequivocally classified as direct OBPs. The remainder suggest a major contribution by indirect, hydroxyl radical induced formation of OBPs in EfOM. Overall, labelled OBPs possess a low degree of unsaturation and contributed most to OBP peak intensity - marking them as potential end products. A few direct and indirect OBPs with high peak intensity containing 18O and heteroatoms (N, S) were fragmented with CID FT-ICR-MS/MS and screened for indicative neutral losses carrying heavy oxygen. The neutral loss screening was used to detect the 18O location on the OBP and indicate the original functional group in EfOM based on known reaction mechanisms. We identified sulfoxide and sulfonic acid functional groups in selected OBPs - implying the presence of reduced sulfur in EfOM molecules - while no evidence for nitrogen containing functional groups reacting with ozone was found.

Absolute EUV reflectivity measurements using a broadband high-harmonic source and an in situ single exposure reference scheme.

We present a tabletop setup for extreme ultraviolet (EUV) reflection spectroscopy in the spectral range from 40 to 100 eV by using high-harmonic radiation. The simultaneous measurements of reference and sample spectra with high energy resolution provide precise and robust absolute reflectivity measurements, even when operating with spectrally fluctuating EUV sources. The stability and sensitivity of EUV reflectivity measurements are crucial factors for many applications in attosecond science, EUV spectroscopy, and nano-scale tomography. We show that the accuracy and stability of our in situ referencing scheme are almost one order of magnitude better in comparison to subsequent reference measurements. We demonstrate the performance of the setup by reflective near-edge x-ray absorption fine structure measurements of the aluminum L2/3 absorption edge in α-Al2O3 and compare the results to synchrotron measurements.

Characterization of encapsulated graphene layers using extreme ultraviolet coherence tomography.

Many applications of two-dimensional materials such as graphene require the encapsulation in bulk material. While a variety of methods exist for the structural and functional characterization of uncovered 2D materials, there is a need for methods that image encapsulated 2D materials as well as the surrounding matter. In this work, we use extreme ultraviolet coherence tomography to image graphene flakes buried beneath 200 nm of silicon. We show that we can identify mono-, bi-, and trilayers of graphene and quantify the thickness of the silicon bulk on top by measuring the depth-resolved reflectivity. Furthermore, we estimate the quality of the graphene interface by incorporating a model that includes the interface roughness. These results are verified by atomic force microscopy and prove that extreme ultraviolet coherence tomography is a suitable tool for imaging 2D materials embedded in bulk materials.

Chlorination of isothiazolinone biocides: kinetics, reactive species, pathway, and toxicity evolution.

Due to the Covid-19 pandemic, the worldwide biocides application has been increased, which will eventually result in enhanced residuals in treated wastewater. At the same time, chlorine disinfection of secondary effluents and hospital wastewaters has been intensified. With respect to predicted elevated exposure in wastewater, the chlorination kinetics, transformation pathways and toxicity evolution were investigated in this study for two typical isothiazolinone biocides, methyl-isothiazolinone (MIT) and chloro-methyl-isothiazolinone (CMIT). Second-order rate constants of 0.13 M-1·s-1, 1.95 × 105 M-1·s-1 and 5.14 × 105 M-1·s-1 were determined for the reaction of MIT with HOCl, Cl2O and Cl2, respectively, while reactivity of CMIT was around 1-2 orders of magnitude lower. While chlorination of isothiazolinone biocides at pH 7.1 was dominated by Cl2O-oxidation, acidic pH and elevated Cl- concentration favored free active chlorine (FAC) speciation into Cl2 and increased overall isothiazolinone removal. Regardless of the dominant FAC species, the elimination of MIT and CMIT resulted in an immediate loss of acute toxicity under all experimental conditions, which was attributed to a preferential attack at the S-atom resulting in subsequent formation of sulfoxides and sulfones and eventually an S-elimination. However, chlorination of isothiazolinone biocides in secondary effluent only achieved <10% elimination at typical disinfection chlorine exposure 200 mg·L-1·min, but was predicted to be remarkably increased by acidizing solution to pH 5.5. Alternative measures might be needed to minimize the discharge of these toxic chemicals into the aquatic environment.

Patterned Growth of Transition Metal Dichalcogenide Monolayers and Multilayers for Electronic and Optoelectronic Device Applications.

A simple, large area, and cost-effective soft lithographic method is presented for the patterned growth of high-quality 2D transition metal dichalcogenides (TMDs). Initially, a liquid precursor (Na2 MoO4 in an aqueous solution) is patterned on the growth substrate using the micromolding in capillaries technique. Subsequently, a chemical vapor deposition step is employed to convert the precursor patterns to monolayer, few layers, or bulk TMDs, depending on the precursor concentration. The grown patterns are characterized using optical microscopy, atomic force microscopy, Raman spectroscopy, X-ray photoelectron spectroscopy, scanning electron microscopy, and photoluminescence spectroscopy to reveal their morphological, chemical, and optical characteristics. Additionally, electronic and optoelectronic devices are realized using the patterned TMDs and tested for their applicability in field effect transistors and photodetectors. The photodetectors made of MoS2 line patterns show a very high responsivity of 7674 A W-1 and external quantum efficiency of 1.49 × 106 %. Furthermore, the multiple grain boundaries present in patterned TMDs enable the fabrication of memtransistor devices. The patterning technique presented here may be applied to many other TMDs and related heterostructures, potentially advancing the fabrication of TMDs-based device arrays.

Synergistic Nanowire-Enhanced Electroporation and Electrochlorination for Highly Efficient Water Disinfection.

Conventional water disinfection methods such as chlorination typically involve the generation of harmful disinfection byproducts and intensive chemical consumption. Emerging electroporation disinfection techniques using nanowire-enhanced local electric fields inactivate microbes by damaging their outer structures without byproduct formation or chemical dosing. However, this physical-based method suffers from a limited inactivation efficiency under high water flux due to an insufficient contact time. Herein, we integrate electrochlorination with nanowire-enhanced electroporation to achieve a synergistic flow-through process for efficient water disinfection targeting bacteria and viruses. Electroporation at the cathode induces sub-lethal damages on the microbial outer structures. Subsequently, electrogenerated active chlorine at the anode aggravates these electroporation-induced injuries to the level of lethal damage. This sequential flow-through disinfection system achieves complete disinfection (>6.0-log) under a very high water flux of 2.4 × 104 L/(m2 h) with an applied voltage of 2.0 V. This disinfection efficiency is 8 times faster than that of electroporation alone. Further, the specific energy consumption for the disinfection by this novel process is extremely low (8 × 10-4 kW h/m3). Our results demonstrate a promising method for rapid and energy-efficient water disinfection by coupling electroporation with electrochlorination to meet vital needs for pathogen elimination.

[Impact and Temporal Evolution of the Corona Pandemic on Pediatric Emergency Care]. / Auswirkungen der Corona Pandemie auf die Notfallversorgung im Kindesalter und die zeitliche Entwicklung im Verlauf der Pandemie.

HINTERGRUND: Die COVID-19 Pandemie hat zu massiven gesellschaftlichen und wirtschaftlichen Einschränkungen geführt. Im Kindesalter wurden elektive Vorsorgeuntersuchung oftmals nicht wahrgenommen und es zeigte sich eine Reduktion der Zahl der Notfallvorstellungen. MATERIAL UND METHODEN: In einer retrospektiven Studie erfolgte eine quantitative Auswertung aller Notfallpatienten der 5 Kindernotaufnahmen Hamburgs und der Kinder- und Jugendarztpraxen der Jahre 2019 und 2020. Zusätzlich erfolgte die detaillierte Analyse der Notfallbehandlungen des Altonaer Kinderkrankenhauses während der ersten Phase der Pandemie im Vergleich zum Vorjahr. Zusammenhänge zu den Eckpunkten der Pandemieentwicklung wurden analysiert. Die Berechnung signifikanter Unterschiede in Bezug auf die demographischen Daten und Krankheitsbilder erfolgte mittels Chi- Quadrat und t-Test. ERGEBNISSE: In allen 5 pädiatrischen Notaufnahmen Hamburgs zeigte sich eine nahezu gleichförmige Abnahme der Patientenvorstellungen während der Pandemie, ähnlich in den Kinder- und Jugendarztpraxen. Die Zahl der Behandlungen verhielt sich dabei nicht streng gegenläufig zu den Neuinfektionen, sondern korreliert eher mit den Mobilitätsdaten und entsprach somit den gesamtgesellschaftlichen Veränderungen. Während der Pandemie stieg der Anteil häuslicher Unfälle an der Gesamtzahl der Vorstellungen signifikant an. Die Analyse der Diagnosen zeigte unter anderem eine relative Abnahme von (viralen) Infektionskrankheiten. Nicht behandlungspflichtige Erkrankungen führten in der Pandemie seltener zur Vorstellung. Diese Phänomene entlasteten einerseits die Notaufnahmen, bergen aber auch die Gefahr, dass Erkrankungen durch Eltern falsch eingeschätzt werden und eine notwendige ärztliche Vorstellung somit zu spät erfolgt.