Effects of different concentrations of intraluminal sodium chloride solution on intracavitary ECG used for arm infusion port implantation.

At present, there are few clinical studies on the application of high-concentration sodium chloride solutions in intracavitary ECG-guided catheter tip localization during the arm infusion port implantation. This study observed the effects of sodium chloride solutions with different concentrations on intracavitary ECG-guided arm infusion port implantation in the patients with cancer. The 657 patients receiving arm infusion port implantation in our hospital between January 2020 and August 2021 were randomly divided into 0.9% sodium chloride solution conduction group (group A), 5.45% sodium chloride solution conduction group (group B) and 10% sodium chloride solution conduction group (group C). The derived rate of stable intracavitary ECG, the occurrence rate of characteristic P wave, the time used for catheter tip localization and the optimal position rate of catheter tip were compared between the three groups. The derived rate of stable intracavitary ECG was significantly higher in the group B (97.78%) and group C (98.63%) than in the group A (93.90%) (all P < 0.05). The occurrence rate of characteristic P wave was also significantly higher in the group B (96.89%) and group C (97.72%) than in the group A (88.73%) (all P < 0.001). The time used for catheter tip localization was significantly shorter in the group B [(49.73 ± 8.15) s] and group C [(48.27 ± 8.61) s] than in the group A [(69.37 ± 19.99) s] (all P < 0.001). There was no significant difference in the optimal position rate of catheter tip among the three groups (P > 0.05). The 5.45% and 10% sodium chloride solutions are significantly superior comparing with 0.9% sodium chloride solution in the derived rate of stable intracavitary ECG, occurrence rate of characteristic P wave and time used for catheter tip localization, but there were no significant differences between 5.45 and 10% sodium chloride solutions. Moreover, the 5.45% sodium chloride solution is closer to physiological state comparing with 10% sodium chloride solution, so the 5.45% sodium chloride solution may be recommended for the intracavitary ECG-guided arm infusion port implantation.

Synergetic metal-semiconductor interaction: Single-atomic Pt decorated CdS nano-photocatalyst for highly water-to-hydrogen conversion.

Solar driven water-to-hydrogen conversion is a promising technology for the typical sustainable production mode, so increasing efforts are being devoted to exploit high-performance photocatalytic materials. Cadmium sulfide (CdS) is widely used to prepare highly active photocatalysts owing to its merits of broadband-light harvesting and feasible band structure. However, the slow photo-carriers' migration in CdS body structure generally results in high-frequency carriers recombination, which leads to unsatisfied photoactivity. Metallic single-atom surface decoration is an effective method to build the strong metal-support interaction for promotion of photo-carriers' migration. Herein, a simple light-induced reduction procedure was proposed to decorate single-atomic Pt on the surface of CdS nanoparticles for highly photocatalytic HER activity. Research showed that the synergetic metal (Pt)-semiconductor (CdS) interaction significantly promoted the body-to-surface (BTS) photo-carriers' migration of CdS, thereby the high light-to-fuel conversion efficiency (AQY500 nm = 25.70%) and 13.5-fold greater simulated sunlight driven HER rate of bare CdS was achieved by this CdS-Pt nano-photocatalyst. Based on the photo-electrochemical analysis and density functional theory calculations, the remarkably improved HER photoactivity can be attributed to the enhanced light-harvesting, promoted BTS electron migration and reduced reaction energy barriers. This study provides a facile procedure to obtain CdS based photocatalyst with metallic single-atom sites for high-performance HER photocatalysis.

[Design and application of a moxibustion device with separated moxibustion smoke and heat].

In the view of the defects of the commonly used moxibustion instruments and moxa heating instruments, such as the moxa ash cannot be removed automatically, the temperature of moxibustion and moxibustion smoke is difficult to be stabilized and adjusted, and the instruments are complex and expensive, a moxibustion device with separated moxibustion smoke and heat is designed. This device can automatically remove the moxa ash and keep it on the isolation net; the temperature of the moxibustion outlet is maintained at 43-48 ℃ (effective moxibustion temperature) for more than 40 minutes, and there is no visible moxa smoke; the temperature of the moxa smoke outlet is controlled between 28-75 ℃, and the effective discharge of moxa smoke can be realized without external power equipment. This device has the advantages of stable and controllable temperature of moxibustion outlet and moxa smoke outlet, automatic removal and collection of moxa ash, separation of moxa smoke without additional power, etc., which can be used in clinical and animal experiments for moxa heating, moxa smoke removal, etc.

Thermal conductivity of graphene nanoribbons under shear deformation: A molecular dynamics simulation.

Tensile strain and compress strain can greatly affect the thermal conductivity of graphene nanoribbons (GNRs). However, the effect of GNRs under shear strain, which is also one of the main strain effect, has not been studied systematically yet. In this work, we employ reverse nonequilibrium molecular dynamics (RNEMD) to the systematical study of the thermal conductivity of GNRs (with model size of 4 nm × 15 nm) under the shear strain. Our studies show that the thermal conductivity of GNRs is not sensitive to the shear strain, and the thermal conductivity decreases only 12-16% before the pristine structure is broken. Furthermore, the phonon frequency and the change of the micro-structure of GNRs, such as band angel and bond length, are analyzed to explore the tendency of thermal conductivity. The results show that the main influence of shear strain is on the in-plane phonon density of states (PDOS), whose G band (higher frequency peaks) moved to the low frequency, thus the thermal conductivity is decreased. The unique thermal properties of GNRs under shear strains suggest their great potentials for graphene nanodevices and great potentials in the thermal managements and thermoelectric applications.

Tertiary montane origin of the Central Asian flora, evidence inferred from cpDNA sequences of Atraphaxis (Polygonaceae).

Atraphaxis has approximately 25 species and a distribution center in Central Asia. It has been previously used to hypothesize an origin from montane forest. We sampled 18 species covering three sections within the genus and sequenced five cpDNA spacers, atpB-rbcL, psbK-psbI, psbA-trnH, rbcL, and trnL-trnF. BEAST was used to reconstruct phylogenetic relationship and time divergences, and S-DIVA and Lagrange were used, based on distribution area and ecotype data, for reconstruction of ancestral areas and events. Our results appear compatible with designation of three taxonomic sections within the genus. The generic stem and crown ages were Eocene, approximately 47 Ma, and Oligocene 27 Ma, respectively. The origin of Atraphaxis is confirmed as montane, with an ancestral area consisting of the Junggar Basin and uplands of the Pamir-Tianshan-Alatau-Altai mountain chains, and ancestral ecotype of montane forest. Two remarkable paleogeographic events, shrinkage of the inland Paratethys Sea at the boundary of the late Oligocene and early Miocene, and the time intervals of cooling and drying of global climate from 24 (22) Ma onward likely facilitated early diversification of Atraphaxis, while rapid uplift of the Tianshan Mountains during the late Miocene may have promoted later diversification.