Mn Additive Improves Zr Grain Boundary Diffusion for Sintering of a Y-Doped BaZrO3 Proton Conductor.

Yttrium-doped barium zirconate (BZY) has garnered attention as a protonic conductor in intermediate-temperature electrolysis and fuel cells due to its high bulk proton conductivity and excellent chemical stability. However, the performance of BZY can be further enhanced by reducing the concentration and resistance of grain boundaries. In this study, we investigate the impact of manganese (Mn) additives on the sinterability and proton conductivity of Y-doped BaZrO3 (BZY). By employing a combinatorial pulsed laser deposition (PLD) technique, we synthesized BZY thin films with varying Mn concentrations and sintering temperatures. Our results revealed a significant enhancement in sinterability as Mn concentrations increased, leading to larger grain sizes and lower grain boundary concentrations. These improvements can be attributed to the elevated grain boundary diffusion of zirconium (Zr) cations, which enhances material densification. We also observed a reduction in Goldschmidt's tolerance factor with increased Mn substitution, which can improve proton transport. The high proton conduction of BZY with Mn additives in low-temperature and wet hydrogen environments makes it a promising candidate for protonic ceramic electrolysis cells and fuel cells. Our findings not only advance the understanding of Mn additives in BZY materials but also demonstrate a high-throughput combinatorial thin film approach to select additives for other perovskite materials with importance in mass and charge transport applications.

Minimizing Interfacial Recombination in 1.8 eV Triple-Halide Perovskites for 27.5% Efficient All-Perovskite Tandems.

All-perovskite tandem solar cells show great potential to enable the highest performance at reasonable costs for a viable market entry in the near future. In particular, wide-bandgap (WBG) perovskites with higher open-circuit voltage (VOC ) are essential to further improve the tandem solar cells' performance. Here, a new 1.8 eV bandgap triple-halide perovskite composition in conjunction with a piperazinium iodide (PI) surface treatment is developed. With structural analysis, it is found that the PI modifies the surface through a reduction of excess lead iodide in the perovskite and additionally penetrates the bulk. Constant light-induced magneto-transport measurements are applied to separately resolve charge carrier properties of electrons and holes. These measurements reveal a reduced deep trap state density, and improved steady-state carrier lifetime (factor 2.6) and diffusion lengths (factor 1.6). As a result, WBG PSCs achieve 1.36 V VOC , reaching 90% of the radiative limit. Combined with a 1.26 eV narrow bandgap (NBG) perovskite with a rubidium iodide additive, this enables a tandem cell with a certified scan efficiency of 27.5%.

Electrochemical Doping of Halide Perovskites by Noble Metal Interstitial Cations.

Metal halide perovskites are an attractive class of semiconductors, but it has proven difficult to control their electronic doping by conventional strategies due to screening and compensation by mobile ions or ionic defects. Noble-metal interstitials represent an under-studied class of extrinsic defects that plausibly influence many perovskite-based devices. In this work, doping of metal halide perovskites is studied by electrochemically formed Au+ interstitial ions, combining experimental data on devices with a computational analysis of Au+ interstitial defects based on density functional theory (DFT). Analysis suggests that Au+ cations can be easily formed and migrate through the perovskite bulk via the same sites as iodine interstitials (Ii + ). However, whereas Ii + compensates n-type doping by electron capture, the noble-metal interstitials act as quasi-stable n-dopants. Experimentally, voltage-dependent, dynamic doping by current density-time (J-t), electrochemical impedance, and photoluminescence measurements are characterized. These results provide deeper insight into the potential beneficial and detrimental impacts of metal electrode reactions on long-term performance of perovskite photovoltaic and light-emitting diodes, as well as offer an alternative doping explanation for the valence switching mechanism of halide-perovskite-based neuromorphic and memristive devices.

Metal Halide Perovskite Heterostructures: Blocking Anion Diffusion with Single-Layer Graphene.

The development of metal halide perovskite/perovskite heterostructures is hindered by rapid interfacial halide diffusion leading to mixed alloys rather than sharp interfaces. To circumvent this outcome, we developed an ion-blocking layer consisting of single-layer graphene (SLG) deposited between the metal halide perovskite layers and demonstrated that it effectively blocks anion diffusion in a CsPbBr3/SLG/CsPbI3 heterostructure. Spatially resolved elemental analysis and spectroscopic measurements demonstrate the halides do not diffuse across the interface, whereas control samples without the SLG show rapid homogenization of the halides and loss of the sharp interface. Ultraviolet photoelectron spectroscopy, DFT calculations, and transient absorbance spectroscopy indicate the SLG has little electronic impact on the individual semiconductors. In the CsPbBr3/SLG/CsPbI3, we find a type I band alignment that supports transfer of photogenerated carriers across the heterointerface. Light-emitting diodes (LEDs) show electroluminescence from both the CsPbBr3 and CsPbI3 layers with no evidence of ion diffusion during operation. Our approach provides opportunities to design novel all-perovskite heterostructures to facilitate the control of charge and light in optoelectronic applications.

Intermediate-phase engineering via dimethylammonium cation additive for stable perovskite solar cells.

Achieving the long-term stability of perovskite solar cells is arguably the most important challenge required to enable widespread commercialization. Understanding the perovskite crystallization process and its direct impact on device stability is critical to achieving this goal. The commonly employed dimethyl-formamide/dimethyl-sulfoxide solvent preparation method results in a poor crystal quality and microstructure of the polycrystalline perovskite films. In this work, we introduce a high-temperature dimethyl-sulfoxide-free processing method that utilizes dimethylammonium chloride as an additive to control the perovskite intermediate precursor phases. By controlling the crystallization sequence, we tune the grain size, texturing, orientation (corner-up versus face-up) and crystallinity of the formamidinium (FA)/caesium (FA)yCs1-yPb(IxBr1-x)3 perovskite system. A population of encapsulated devices showed improved operational stability, with a median T80 lifetime (the time over which the device power conversion efficiency decreases to 80% of its initial value) for the steady-state power conversion efficiency of 1,190 hours, and a champion device showed a T80 of 1,410 hours, under simulated sunlight at 65 °C in air, under open-circuit conditions. This work highlights the importance of material quality in achieving the long-term operational stability of perovskite optoelectronic devices.

Compositional texture engineering for highly stable wide-bandgap perovskite solar cells.

The development of highly stable and efficient wide-bandgap (WBG) perovskite solar cells (PSCs) based on bromine-iodine (Br-I) mixed-halide perovskite (with Br greater than 20%) is critical to create tandem solar cells. However, issues with Br-I phase segregation under solar cell operational conditions (such as light and heat) limit the device voltage and operational stability. This challenge is often exacerbated by the ready defect formation associated with the rapid crystallization of Br-rich perovskite chemistry with antisolvent processes. We combined the rapid Br crystallization with a gentle gas-quench method to prepare highly textured columnar 1.75-electron volt Br-I mixed WBG perovskite films with reduced defect density. With this approach, we obtained 1.75-electron volt WBG PSCs with greater than 20% power conversion efficiency, approximately 1.33-volt open-circuit voltage (Voc), and excellent operational stability (less than 5% degradation over 1100 hours of operation under 1.2 sun at 65°C). When further integrated with 1.25-electron volt narrow-bandgap PSC, we obtained a 27.1% efficient, all-perovskite, two-terminal tandem device with a high Voc of 2.2 volts.

Gradient Doping in Sn-Pb Perovskites by Barium Ions for Efficient Single-Junction and Tandem Solar Cells.

Narrow-bandgap (NBG) tin (Sn)-lead (Pb) perovskites generally have a high density of unintentional p-type self-doping, which reduces the charge-carrier lifetimes, diffusion lengths, and device efficiencies. Here, a p-n homojunction across the Sn-Pb perovskite is demonstrated, which results from a gradient doping by barium ions (Ba2+ ). It is reported that 0.1 mol% Ba2+ can effectively compensate the p-doping of Sn-Pb perovskites or even turns it to n-type without changing its bandgap. Ba2+ cations are found to stay at the interstitial sites and work as shallow electron donor. In addition, Ba2+ cations show a unique heterogeneous distribution in perovskite film. Most of the barium ions stay in the top 600 nm region of the perovskite films and turn it into weakly n-type, while the bottom portion of the film remains as p-type. The gradient doping forms a homojunction from top to bottom of the perovskite films with a built-in field that facilitates extraction of photogenerated carriers, resulting in an increased carrier extraction length. This strategy enhances the efficiency of Sn-Pb perovskite single-junction solar cells to over 21.0% and boosts the efficiencies of monolithic perovskite-perovskite tandem solar cells to 25.3% and 24.1%, for active areas of 5.9 mm2  and 0.94 cm2 , respectively.

Green MIP-202(Zr) Catalyst: Degradation and Thermally Robust Biomimetic Sensing of Nerve Agents.

Rapid and robust sensing of nerve agent (NA) threats is necessary for real-time field detection to facilitate timely countermeasures. Unlike conventional phosphotriesterases employed for biocatalytic NA detection, this work describes the use of a new, green, thermally stable, and biocompatible zirconium metal-organic framework (Zr-MOF) catalyst, MIP-202(Zr). The biomimetic Zr-MOF-based catalytic NA recognition layer was coupled with a solid-contact fluoride ion-selective electrode (F-ISE) transducer, for potentiometric detection of diisopropylfluorophosphate (DFP), a F-containing G-type NA simulant. Catalytic DFP degradation by MIP-202(Zr) was evaluated and compared to the established UiO-66-NH2 catalyst. The efficient catalytic DFP degradation with MIP-202(Zr) at near-neutral pH was validated by 31P NMR and FT-IR spectroscopy and potentiometric F-ISE and pH-ISE measurements. Activation of MIP-202(Zr) using Soxhlet extraction improved the DFP conversion rate and afforded a 2.64-fold improvement in total percent conversion over UiO-66-NH2. The exceptional thermal and storage stability of the MIP-202/F-ISE sensor paves the way toward remote/wearable field detection of G-type NAs in real-world environments. Overall, the green, sustainable, highly scalable, and biocompatible nature of MIP-202(Zr) suggests the unexploited scope of such MOF catalysts for on-body sensing applications toward rapid on-site detection and detoxification of NA threats.

Substrate Analogues for the Enzyme-Catalyzed Detoxification of the Organophosphate Nerve Agents-Sarin, Soman, and Cyclosarin.

The G-type nerve agents, sarin (GB), soman (GD), and cyclosarin (GF), are among the most toxic compounds known. Much progress has been made in evolving the enzyme phosphotriesterase (PTE) from Pseudomonas diminuta for the decontamination of the G-agents; however, the extreme toxicity of the G-agents makes the use of substrate analogues necessary. Typical analogues utilize a chromogenic leaving group to facilitate high-throughput screening, and substitution of an O-methyl for the P-methyl group found in the G-agents, in an effort to reduce toxicity. Till date, there has been no systematic evaluation of the effects of these substitutions on catalytic activity, and the presumed reduction in toxicity has not been tested. A series of 21 G-agent analogues, including all combinations of O-methyl, p-nitrophenyl, and thiophosphate substitutions, have been synthesized and evaluated for their ability to unveil the stereoselectivity and catalytic activity of PTE variants against the authentic G-type nerve agents. The potential toxicity of these analogues was evaluated by measuring the rate of inactivation of acetylcholinesterase (AChE). All of the substitutions reduced inactivation of AChE by more than 100-fold, with the most effective being the thiophosphate analogues, which reduced the rate of inactivation by about 4-5 orders of magnitude. The analogues were found to reliably predict changes in catalytic activity and stereoselectivity of the PTE variants and led to the identification of the BHR-30 variant, which has no apparent stereoselectivity against GD and a kcat/Km of 1.4 × 106, making it the most efficient enzyme for GD decontamination reported till date.

Textile-based wearable solid-contact flexible fluoride sensor: Toward biodetection of G-type nerve agents.

Rising global concerns posed by chemical and biological threat agents highlight the critical need to develop reliable strategies for the real-time detection of such threats. While wearable sensing technology is well suited to fulfill this task, the use of on-body devices for rapid and selective field identification of chemical agents is relatively a new area. This work describes a flexible printed textile-based solid-contact potentiometric sensor for the selective detection of fluoride anions liberated by the biocatalytic hydrolysis of fluorine-containing G-type nerve agents (such as sarin or soman). The newly developed solid-contact textile fluoride sensor relies on a fluoride-selective bis(fluorodioctylstannyl)methane ionophore to provide attractive analytical performance with near-Nernstian sensitivity and effective discrimination against common anions, along with excellent reversibility and repeatability for dynamically changing fluoride concentrations. By using stress-enduring printed inks and serpentine structures along with stretchable textile substrates, the resulting textile-based fluoride sensor exhibits robust mechanical resiliency under severe mechanical strains. Such realization of an effective textile-based fluoride-selective electrode allowed biosensing of the nerve-agent simulant diisopropyl fluorophosphate (DFP), in connection to immobilized organophosphorus acid anhydrolylase (OPAA) or organophosphorus hydrolase (OPH) enzymes. A user-friendly portable electronic module transmits data from the new textile-based potentiometric biosensor wirelessly to a nearby smartphone for alerting the wearer instantaneously about potential chemical threats. While expanding the scope of wearable solid-contact anion sensors, such a textile-based potentiometric fluoride electrode transducer offers particular promise for effective discrimination of G-type neurotoxins from organophosphate (OP) pesticides, toward specific field detection of these agents in diverse defense settings.

Low-energy room-temperature optical switching in mixed-dimensionality nanoscale perovskite heterojunctions.

Long-lived photon-stimulated conductance changes in solid-state materials can enable optical memory and brain-inspired neuromorphic information processing. It remains challenging to realize optical switching with low-energy consumption, and new mechanisms and design principles giving rise to persistent photoconductivity (PPC) can help overcome an important technological hurdle. Here, we demonstrate versatile heterojunctions between metal-halide perovskite nanocrystals and semiconducting single-walled carbon nanotubes that enable room-temperature, long-lived (thousands of seconds), writable, and erasable PPC. Optical switching and basic neuromorphic functions can be stimulated at low operating voltages with femto- to pico-joule energies per spiking event, and detailed analysis demonstrates that PPC in this nanoscale interface arises from field-assisted control of ion migration within the nanocrystal array. Contactless optical measurements also suggest these systems as potential candidates for photonic synapses that are stimulated and read in the optical domain. The tunability of PPC shown here holds promise for neuromorphic computing and other technologies that use optical memory.

Chiral-induced spin selectivity enables a room-temperature spin light-emitting diode.

In traditional optoelectronic approaches, control over spin, charge, and light requires the use of both electrical and magnetic fields. In a spin-polarized light-emitting diode (spin-LED), charges are injected, and circularly polarized light is emitted from spin-polarized carrier pairs. Typically, the injection of carriers occurs with the application of an electric field, whereas spin polarization can be achieved using an applied magnetic field or polarized ferromagnetic contacts. We used chiral-induced spin selectivity (CISS) to produce spin-polarized carriers and demonstrate a spin-LED that operates at room temperature without magnetic fields or ferromagnetic contacts. The CISS layer consists of oriented, self-assembled small chiral molecules within a layered organic-inorganic metal-halide hybrid semiconductor framework. The spin-LED achieves ±2.6% circularly polarized electroluminescence at room temperature.

Effect of Water Concentration in LiPF6-Based Electrolytes on the Formation, Evolution, and Properties of the Solid Electrolyte Interphase on Si Anodes.

A trace amount of water in an electrolyte is one of the factors detrimental to the electrochemical performance of silicon (Si)-based lithium-ion batteries that adversely affect the formation and evolution of the solid electrolyte interphase (SEI) on Si-based anodes and change its properties. Thus far, a lack of fundamental and mechanistic understanding of SEI formation, evolution, and properties in the presence of water has inhibited efforts to stabilize the SEI for improved electrochemical performance. Thus, we investigated the SEI formed in a Gen2 electrolyte (1.2 M LiPF6 in ethylene carbonate/ethyl methyl carbonate, 3:7 wt %, water content: <10 ppm) with and without additional water (50 ppm) at varying potentials (1.0, 0.5, 0.2, and 0.01 V vs Li/Li+). The impact of additional water on the morphological, (electro)chemical, and structural properties of SEI was studied using microscopic (atomic force microscopy and scanning spreading resistance microscopy) and spectroscopic (X-ray photoelectron spectroscopy, attenuated total reflection Fourier-transform infrared spectroscopy, and time-of-flight secondary ion mass spectrometry) techniques. The SEI exhibits both potential- and water concentration-dependent trends in its morphology and chemical composition. The presence of additional water in the electrolyte causes parasitic reactions, which onset at ∼1.0 V, resulting in a reduction of electrolyte components and result in the formation of an insulating, fluorophosphate-rich SEI. In addition, hydrolysis of LiPF6 creates hydrofluoric acid, which reacts with the surface oxide layer on the Si electrode, leading to a pitted and inhomogeneous SEI structure.

Surface SiO2 Thickness Controls Uniform-to-Localized Transition in Lithiation of Silicon Anodes for Lithium-Ion Batteries.

Silicon is a promising anode material for lithium-ion batteries because of its high capacity, but its widespread adoption has been hampered by a low cycle life arising from mechanical failure and the absence of a stable solid-electrolyte interphase (SEI). Understanding SEI formation and its impact on cycle life is made more complex by the oxidation of silicon materials in air or during synthesis, which leads to SiOx coatings of varying thicknesses that form the true surface of the electrode. In this paper, the lithiation of SiO2-coated Si is studied in a controlled manner using SiO2 coatings of different thicknesses grown on Si wafers via thermal oxidation. SiO2 thickness has a profound effect on lithiation: below 2 nm, SEI formation followed by uniform lithiation occurs at positive voltages versus Li/Li+. Si lithiation is reversible, and SiO2 lithiation is largely irreversible. Above 2 nm SiO2, voltammetric currents decrease exponentially with SiO2 thickness. For 2-3 nm SiO2, SEI formation above 0.1 V is suppressed, but a hold at low or negative voltages can initiate charge transfer whereupon SEI formation and uniform lithiation occur. Cycling of Si anodes with an SiO2 coating thinner than 3 nm occurs at high Coulombic efficiency (CE). If an SiO2 coating is thicker than 3-4 nm, the behavior is totally different: lithiation at positive voltages is strongly inhibited, and lithiation occurs at poor CE and is highly localized at pinholes which grow over time. As they grow, lithiation becomes more facile and the CE increases. Pinhole growth is proposed to occur via rapid transport of Li along the SiO2/Si interface radially outward from an existing pinhole, followed by the lithiation of SiO2 from the interface outward.

Structural and kinetic evidence of aging after organophosphate inhibition of human Cathepsin A.

Human Cathepsin A (CatA) is a lysosomal serine carboxypeptidase of the renin-angiotensin system (RAS) and is structurally similar to acetylcholinesterase (AChE). CatA can remove the C-terminal amino acids of endothelin I, angiotensin I, Substance P, oxytocin, and bradykinin, and can deamidate neurokinin A. Proteomic studies identified CatA and its homologue, SCPEP1, as potential targets of organophosphates (OP). CatA could be stably inhibited by low µM to high nM concentrations of racemic sarin (GB), soman (GD), cyclosarin (GF), VX, and VR within minutes to hours at pH 7. Cyclosarin was the most potent with a kinetically measured dissociation constant (KI) of 2 µM followed by VR (KI = 2.8 µM). Bimolecular rate constants for inhibition by cyclosarin and VR were 1.3 × 103 M-1sec-1 and 1.2 × 103 M-1sec-1, respectively, and were approximately 3-orders of magnitude lower than those of human AChE indicating slower reactivity. Notably, both AChE and CatA bound diisopropylfluorophosphate (DFP) comparably and had KIDFP = 13 µM and 11 µM, respectively. At low pH, greater than 85% of the enzyme spontaneously reactivated after OP inhibition, conditions under which OP-adducts of cholinesterases irreversibly age. At pH 6.5 CatA remained stably inhibited by GB and GF and <10% of the enzyme spontaneously reactivated after 200 h. A crystal structure of DFP-inhibited CatA was determined and contained an aged adduct. Similar to AChE, CatA appears to have a "backdoor" for product release. CatA has not been shown previously to age. These results may have implications for: OP-associated inflammation; cardiovascular effects; and the dysregulation of RAS enzymes by OP.

Triple-halide wide-band gap perovskites with suppressed phase segregation for efficient tandems.

Wide-band gap metal halide perovskites are promising semiconductors to pair with silicon in tandem solar cells to pursue the goal of achieving power conversion efficiency (PCE) greater than 30% at low cost. However, wide-band gap perovskite solar cells have been fundamentally limited by photoinduced phase segregation and low open-circuit voltage. We report efficient 1.67-electron volt wide-band gap perovskite top cells using triple-halide alloys (chlorine, bromine, iodine) to tailor the band gap and stabilize the semiconductor under illumination. We show a factor of 2 increase in photocarrier lifetime and charge-carrier mobility that resulted from enhancing the solubility of chlorine by replacing some of the iodine with bromine to shrink the lattice parameter. We observed a suppression of light-induced phase segregation in films even at 100-sun illumination intensity and less than 4% degradation in semitransparent top cells after 1000 hours of maximum power point (MPP) operation at 60°C. By integrating these top cells with silicon bottom cells, we achieved a PCE of 27% in two-terminal monolithic tandems with an area of 1 square centimeter.

Hydrolysis and enzymatic degradation of Novichok nerve agents.

Several parameters of the Novichok nerve agents A230, A232 and A234 were determined. Hydrolysis rates were approximately one to three orders of magnitude slower than G-type nerve agents and approximately zero to two orders of magnitude slower than V-type nerve agents. A230 was the most labile Novichok compound followed by A232 then A234. Activation energies (Ea) and frequency factors (A) were determined for all three compounds. The organophosphorus acid anhydrolase (OPAA) enzyme had catalytic efficiencies on the Novichok compounds ranging between 104 and 105 M-1 min-1 with the highest k cat/Km value for A230, then A232 and lastly, A234.

High-Throughput Screening of MOFs for Breakdown of V-Series Nerve Agents.

Metal-organic frameworks (MOFs) have shown promise for the catalytic decomposition of chemical weapons. Finding the best materials for the degradation of nerve agents requires the ability to screen a high number of samples and elucidate the key parameters of effective catalysis. In this work, a high-throughput screening (HTS) method has been developed to evaluate MOFs as catalysts, specifically against the V-class of nerve agents. Over 100 MOFs have been tested using the V-class simulant, O,O-diethyl S-phenyl phosphorothioate (DEPPT), revealing good activity for some UiO-66 derivatives. A medium-throughput hydrolysis assay for the nerve agent O-ethyl S-[2-(diisopropylamino)ethyl]methylphosphonothioate (VX) was also performed using six MOFs selected from HTS and was validated by 31P NMR. The results demonstrated that the DEPPT-based assay is a good indicator of V-series agent reactivity and should be considered in addition to the common (4-nitrophenyl)phosphate (DMNP) assay that is used for G-series agents.

Intrinsic Properties of Individual Inorganic Silicon-Electrolyte Interphase Constituents.

Because of the complexity, high reactivity, and continuous evolution of the silicon-electrolyte interphase (SiEI), "individual" constituents of the SiEI were investigated to understand their physical, electrochemical, and mechanical properties. For the analysis of these intrinsic properties, known SiEI components (i.e., SiO2, Li2Si2O5, Li2SiO3, Li3SiOx, Li2O, and LiF) were selected and prepared as amorphous thin films. The chemical composition, purity, morphology, roughness, and thickness of prepared samples were characterized using a variety of analytical techniques. On the basis of subsequent analysis, LiF shows the lowest ionic conductivity and relatively weak, brittle mechanical properties, while lithium silicates demonstrate higher ionic conductivities and greater mechanical hardness. This research establishes a framework for identifying components critical for stabilization of the SiEI, thus enabling rational design of new electrolyte additives and functional binders for the development of next-generation advanced Li-ion batteries utilizing Si anodes.