Separating NOM from salts in ion exchange brine with ceramic nanofiltration.

In drinking water treatment, natural organic matter (NOM) is effectively removed from surface water using ion exchange (IEX). A main drawback of using IEX for NOM removal is the production of spent IEX regeneration brine, a polluting waste that is expensive to discharge. In this work, we studied ceramic nanofiltration as a treatment for the spent NOM-rich brine, with the aim to reduce the volume of this waste and to recycle salt. Compared to polymeric nanofiltration, the fouling was limited. When NOM is rejected and concentrated, a clean permeate with the regeneration salt (NaCl) could be produced and reused in the IEX regeneration process. Bench scale studies revealed that NOM could be effectively separated from the NaCl solution by steric effects. However, the separation of NaCl from other salts present in the brine, such as Na2SO4, was not sufficient for reuse purposes. The low sulphate rejection was mainly due to the low zeta potential of the membrane at the high ionic strength of the brine. The permeate of the ceramic nanofiltration should be treated further to obtain a sodium chloride quality that can be recycled as a regenerant solution for ion exchange. Further treatment steps will benefit from the removal of NOM from the brine.

Arsenic removal from geothermal influenced groundwater with low pressure NF pilot plant for drinking water production in Nicaraguan rural communities.

This research evaluated the effect of different fluxes (16, 23 & 30 L/m2 h) and temperatures (31,35 & 43 °C) on the rejection of As(V) during nanofiltration (NF) of natural geothermal influenced groundwater in Nicaragua. A NF pilot plant powered by solar panels was built and operated in rural community Telica, exposed to As-rich drinking water sources due to geothermal influences. The results showed that even at high temperatures it is possible to obtain high rejection of As(V) (0.87-0.9) during NF filtration (recovery 10%; flux 16 L/m2 h) of geothermal influenced groundwater, with the additional advantage of requiring low operating pressures (1.2 bar ~ 12mwc). The permeate concentration (~5 µg/L) complied with the WHO guideline for drinking water and the concentrate (~55 µg/L) could be used by local villagers for daily activities (e.g., laundry and bathing). For all investigated fluxes and temperatures the order of rejection of As(V) (as HAsO42-), compared with the other anions, could be interpreted on the basis of its charge, hydrated radius and hydration free energy. At lower temperatures (31 and 35 °C) permeate quality improved slightly (~3 µg/L), but although an increased temperature had a negative effect on the As rejection, As concentrations in the permeate never exceeded 5 µg/L, while the required TMP dropped - depending on the flux - with 0.5 to 1 bar. This decrease in required pressure might be of huge benefit in deserted, rural locations where electricity is scarce, as with an overhead tank of 10-15 m a gravity-fed NF system would be feasible.

High flow ceramic pot filters.

Ceramic pot filters are considered safe, robust and appropriate technologies, but there is a general consensus that water revenues are limited due to clogging of the ceramic element. The objective of this study was to investigate the potential of high flow ceramic pot filters to produce more water without sacrificing their microbial removal efficacy. High flow pot filters, produced by increasing the rice husk content, had a higher initial flow rate (6-19 L h-1), but initial LRVs for E. coli of high flow filters was slightly lower than for regular ceramic pot filters. This disadvantage was, however, only temporarily as the clogging in high flow filters had a positive effect on the LRV for E. coli (from below 1 to 2-3 after clogging). Therefore, it can be carefully concluded that regular ceramic pot filters perform better initially, but after clogging, the high flow filters have a higher flow rate as well as a higher LRV for E. coli. To improve the initial performance of new high flow filters, it is recommended to further utilize residence time of the water in the receptacle, since additional E. coli inactivation was observed during overnight storage. Although a relationship was observed between flow rate and LRV of MS2 bacteriophages, both regular and high flow filters were unable to reach over 2 LRV.

Visualization of hydraulic conditions inside the feed channel of Reverse Osmosis: A practical comparison of velocity between empty and spacer-filled channel.

It is widely accepted that our understanding about the membrane process increases by investigation of the hydraulic conditions of membranes. While numerical studies have been broadly used for this purpose, the experimental studies of a comparable resolution are scarce. In this study, we compared the pressure drop, the temporal and the spatial velocity maps of a spacer-filled channel and an empty channel of the same size to determine the effect of presence of the feeds spacer on hydraulic conditions. The velocity maps are obtained experimentally by using of the Particle Image Velocimetry (PIV) technique. Application of the feed spacer caused 2-8.5 higher pressure drop increase in the experimental conditions in this research. The flow had a spatial distribution in the form of a unimodal symmetric curve of normal distribution in the empty channel and a bimodal asymmetric curve in the spacer-filled channel. The bimodal curve indicates the presence of high- and low-velocity zones. Additionally, the low-velocity zones showed also a lower variation of velocity in time, which indicates the high fouling potential of these locations. The results from this study may be uses for validation of numerical studies.

Clay-starch combination for micropollutants removal from wastewater treatment plant effluent.

In this study, a new, more effective and cost-effective treatment alternative is investigated for the removal of pharmaceuticals from wastewater treatment plant effluent (WWTP-eff). The potential of combining clay with biodegradable polymeric flocculants is further highlighted. Flocculation is viewed as the best method to get the optimum outcome from clay. In addition, flocculation with cationic starch increases the biodegradability and cost of the treatment. Clay is naturally abundantly available and relatively inexpensive compared to conventional adsorbents. Experimental studies were carried out with existing naturally occurring pharmaceutical concentrations found and measured in WWTP-eff with atrazine spiking for comparison between the demineralised water and WWTP-eff matrix. Around 70% of the total measured pharmaceutical compounds were removable by the clay-starch combination. The effect of clay with and without starch addition was also highlighted.

Critical parameters in the production of ceramic pot filters for household water treatment in developing countries.

The need to improve the access to safe water is generally recognized for the benefit of public health in developing countries. This study's objective was to identify critical parameters which are essential for improving the performance of ceramic pot filters (CPFs) as a point-of-use water treatment system. Defining critical production parameters was also relevant to confirm that CPFs with high-flow rates may have the same disinfection capacity as pots with normal flow rates. A pilot unit was built in Cambodia to produce CPFs under controlled and constant conditions. Pots were manufactured from a mixture of clay, laterite and rice husk in a small-scale, gas-fired, temperature-controlled kiln and tested for flow rate, removal efficiency of bacteria and material strength. Flow rate can be increased by increasing pore sizes and by increasing porosity. Pore sizes were increased by using larger rice husk particles and porosity was increased with larger proportions of rice husk in the clay mixture. The main conclusions: larger pore size decreases the removal efficiency of bacteria; higher porosity does not affect the removal efficiency of bacteria, but does influence the strength of pots; flow rates of CPFs can be raised to 10-20 L/hour without a significant decrease in bacterial removal efficiency.

Polyelectrolytes ability in reducing atrazine concentration in water: surface effects.

This paper reports on the direct ability of two positively charged organic polyelectrolytes (natural-based and synthetic) to reduce the atrazine concentration in water. The adsorption study was set up using multiple glass vessels with different polymer dosing levels followed by ultrafiltration with a 1 kDa membrane. The addition of polymers exhibited a capability in reducing the atrazine concentration up to a maximum of 60% in surface-to-volume ratio experiments. In the beginning, the theoretical L-type of the isotherm of Giles' classification was expected with an increase in the dosage of the polymer. However, in this study, the conventional type of isotherm was not observed. It was found that the adsorption of the cationic polymer on the negatively charged glass surface was necessary and influential for the removal of atrazine. Surface-to-volume ratio adsorption experiments were performed to elucidate the mechanisms and the polymer configuration. The glass surface area was determined to be a limiting parameter in the adsorption mechanism.

Bacteria and virus removal effectiveness of ceramic pot filters with different silver applications in a long term experiment.

In 2012 more than 4 million people used a ceramic pot filter (CPF) as household water treatment system for their daily drinking water needs. In the normal production protocol most low cost filters are impregnated with a silver solution to enhance the microbial removal efficiency. The aim of this study was to determine the role of silver during the filtration and subsequent storage. Twenty-two CPFs with three different silver applications (non, only outside and both sides) were compared in a long-term loading experiment with Escherichia coli (K12 and WR1) and MS2 bacteriophages in natural challenge water under highly controlled laboratory circumstances. No significant difference in Log Removal Values were found between the filters with different silver applications. The results show that the storage time in the receptacle is the dominant parameter to reach E. coli inactivation by silver, and not the contact time during the filtration phase. The hypothesis that the absence of silver would enhance the virus removal, due to biofilm formation on the ceramic filter element, could not be confirmed. The removal effectiveness for viruses is still of major concern for the CPF. This study suggests that the ceramic pot filter characteristics, such as burnt material content, do not determine E. coli removal efficacies, but rather the contact time with silver during storage is the dominant parameter to reach E. coli inactivation.

Effect of different temperatures on performance and membrane fouling in high concentration PAC-MBR system treating micro-polluted surface water.

A bench-scale immersed microfiltration coupled with 50 g/L PAC was developed to treat micro-polluted surface water (MPSW) under 10 and 20 °C and the effects of temperatures on the performance and the membrane fouling were also investigated. The low temperature (10 °C) delayed the time for the start-up by 9 days and the complete nitrification by 10 days. In the stable operation, two systems both had high NH3-N removal efficiency (above 90%) and better removal of organic matters (10% DOC, 5% UV254 and 4% SUVA) at 10 °C. Polysaccharides (SMP) were the main membrane fouling matters at low temperature (10 °C) and low temperature (10 °C) didn't cause serious chemical irreversible membrane fouling.

High concentration powdered activated carbon-membrane bioreactor (PAC-MBR) for slightly polluted surface water treatment at low temperature.

In this study, different concentrations of PAC combined with MBR were carried out to treat slightly polluted surface water (SPSW) at low temperature (10°C). Effects of PAC on the efficiencies of operation, treatment, and the performance of the process were investigated. It was found that the effluent quality, performance efficiency, resistance of shock load were all enhanced and chemical irreversible membrane fouling was reduced with increasing dosage of PAC in MBR. Only when the concentration of PAC which acted as biological carriers was high enough (i.g., 50 g/L), nitrification without initial inoculation in the filtration tank could start within 19 days and be completed within 35 days at 10°C. Fifty grams per liter PAC was the optimal dosage in MBR for stable and extended operation. Under this condition, mean removal efficiencies of ammonia nitrogen (NH(3)-N), dissolved organic carbon (DOC) and UV(254) were 93%, 75%, and 85%, respectively.

Fouling control mechanisms of demineralized water backwash: Reduction of charge screening and calcium bridging effects.

This paper investigates the impact of the ionic environment on the charge of colloidal natural organic matter (NOM) and ultrafiltration (UF) membranes (charge screening effect) and the calcium adsorption/bridging on new and fouled membranes (calcium bridging effect) by measuring the zeta potentials of membranes and colloidal NOM. Fouling experiments were conducted with natural water to determine whether the reduction of the charge screening effect and/or calcium bridging effect by backwashing with demineralized water can explain the observed reduction in fouling. Results show that the charge of both membranes and NOM, as measured by the zeta potential, became more negative at a lower pH and a lower concentration of electrolytes, in particular, divalent electrolytes. In addition, calcium also adsorbed onto the membranes, and consequently bridged colloidal NOM and membranes via binding with functional groups. The charge screening effect could be eliminated by flushing NOM and membranes with demineralized water, since a cation-free environment was established. However, only a limited amount of the calcium bridging connection was removed with demineralized water backwashes, so the calcium bridging effect mostly could not be eliminated. As demineralized water backwash was found to be effective in fouling control, it can be concluded that the reduction of the charge screening is the dominant mechanism for this.

Influence of natural organic matter on equilibrium adsorption of neutral and charged pharmaceuticals onto activated carbon.

Natural organic matter (NOM) can influence pharmaceutical adsorption onto granular activated carbon (GAC) by direct adsorption competition and pore blocking. However, in the literature there is limited information on which of these mechanisms is more important and how this is related to NOM and pharmaceutical properties. Adsorption batch experiments were carried out in ultrapure, waste- and surface water and fresh and NOM preloaded GAC was used. Twenty-one pharmaceuticals were selected with varying hydrophobicity and with neutral, negative or positive charge. The influence of NOM competition and pore blocking could not be separated. However, while reduction in surface area was similar for both preloaded GACs, up to 50% lower pharmaceutical removal was observed on wastewater preloaded GAC. This was attributed to higher hydrophobicity of wastewater NOM, indicating that NOM competition may influence pharmaceutical removal more than pore blocking. Preloaded GAC was negatively charged, which influenced removal of charged pharmaceuticals significantly. At a GAC dose of 6.7 mg/L, negatively charged pharmaceuticals were removed for 0-58%, while removal of positively charged pharmaceuticals was between 32-98%. Charge effects were more pronounced in ultrapure water, as it contained no ions to shield the surface charge. Solutes with higher log D could compete better with NOM, resulting in higher removal.

Subsurface iron and arsenic removal: low-cost technology for community-based water supply in Bangladesh.

The principle of subsurface or in situ iron and arsenic removal is that aerated water is periodically injected into an anoxic aquifer through a tube well, displacing groundwater containing Fe(II). An oxidation zone is created around the tube well where Fe(II) is oxidised. The freshly formed iron hydroxide surfaces provide new sorption sites for soluble Fe(II) and arsenic. The system's efficiency is determined based on the ratio between abstracted volume with reduced iron/arsenic concentrations (V) and the injected volume (V(i)). In the field study presented in this paper, the small-scale application of this technology was investigated in rural Bangladesh. It was found that at small injection volumes (<1 m³) iron removal was successful and became more effective with every successive cycle. For arsenic, however, the system did not prove to be very effective yet. Arsenic retardation was only limited and breakthrough of 10 µg/L (WHO guideline) was observed before V/V(i)=1, which corresponds to arrival of groundwater at the well. Possible explanations for insufficient arsenic adsorption are the short contact times within the oxidation zone, and the presence of competing anions, like phosphate.

Modeling equilibrium adsorption of organic micropollutants onto activated carbon.

Solute hydrophobicity, polarizability, aromaticity and the presence of H-bond donor/acceptor groups have been identified as important solute properties that affect the adsorption on activated carbon. However, the adsorption mechanisms related to these properties occur in parallel, and their respective dominance depends on the solute properties as well as carbon characteristics. In this paper, a model based on multivariate linear regression is described that was developed to predict equilibrium carbon loading on a specific activated carbon (F400) for solutes reflecting a wide range of solute properties. In order to improve prediction accuracy, groups (bins) of solutes with similar solute properties were defined and solute removals were predicted for each bin separately. With these individual linear models, coefficients of determination (R(2)) values ranging from 0.61 to 0.84 were obtained. With the mechanistic approach used in developing this predictive model, a strong relation with adsorption mechanisms is established, improving the interpretation and, ultimately, acceptance of the model.

Influence of electrostatic interactions on the rejection with NF and assessment of the removal efficiency during NF/GAC treatment of pharmaceutically active compounds in surface water.

The removal efficiency of several pharmaceutically active compounds from two different surface water types was investigated. Two different nanofiltration (NF) membranes (Trisep TS-80 and Desal HL) were first studied at low feed water recoveries (10%). In a second phase, the combination of an NF unit at higher feed water recovery (80%) with subsequent granular activated carbon (GAC) filtration of the permeate was investigated. Results indicate that removal of the selected pharmaceuticals with NF is mainly influenced by charge effects: negatively charged solutes are better removed, compared with uncharged solutes, which are, in turn, better removed compared with positively charged solutes. This latter trend is mainly due to charge attractions between the negatively charged membrane surface and positively charged solutes. Increasing feed concentrations of positively charged pharmaceuticals lead to increasing rejection values, due to membrane charge-shielding effects. The removal efficiency of pharmaceuticals with the combination NF/GAC is extremely high. This is mainly due to an increased adsorption capacity of the activated carbon since the largest part of the natural organic matter (NOM) is removed in the NF step. This NOM normally competes with pharmaceuticals for adsorption sites on the carbon.