Low-cost and easy-to-use "on-chip ELISA" for developing health-promoting foods.

We have determined that a biological molecule can be physically immobilized on a polymer containing an azobenzene (azopolymer) using irradiating light. We immobilized antibodies and antigens on the surface of an azopolymer coated glass slide (antibody array) to establish "on-chip ELISAs". The assays used the flat-surface of a glass slide and could be applied to both sandwich and competitive ELISAs. The sensitivity and accuracy of the on-chip ELISA were similar to a conventional ELISA using a polystyrene plate. Using the assay system, we proved that representative oxidative-biomarkers could be simultaneously measured from uL of urine. That should realize low-cost study on animal or human, and accelerate development of health-promoting foods. So, this new concept antibody array has promising applications in proteomic studies, and could be used to examine biomarkers to investigate health-promoting food.

Virus-templated photoimprint on the surface of an azobenzene-containing polymer.

A photoimprint-based immobilization process is presented for cylindrical viruses on the surface of an azobenzene-bearing acrylate polymer by using atomic force microscopy (AFM). Tobacco mosaic virus (TMV), 18 nm in diameter and ca. 300 nm in length, was employed as a model virus. First, a droplet of an aqueous solution containing TMV was placed on the acrylate polymer surface. After drying the droplet, the polymer surface was irradiated with light at a wavelength of 470 nm from blue-light-emitting diodes. Finally, the surface was washed by aqueous solution with detergents. The polymer surface was observed at each step by AFM. TMV was shown to embed itself gradually on the polymer surface during photoirradiation in a time scale of tens of minutes because of the formation of the surface groove complementary to the shape of TMV. Analysis of immobilization efficiency of TMV on the polymer surface by the immunological enzyme luminescence indicated that efficiency increased proportional to the photoirradiation time. In these experimental conditions, the absorption band of the azobenzene moiety remained constant before and after the photoirradiation. These results show that TMV is physically held on the complementary groove formed on the polymer surface by the photoirradiation.

Orientation control of photo-immobilized antibodies on the surface of azobenzene-containing polymers by the introduction of functional groups.

In our photo-induced immobilization technique for an antibody (IgG) using azopolymers, the introduction of COOH and NMe(2) into the azopolymers, which can introduce surface charges, strongly affected the immobilization properties such as the efficiency of immobilization and the activity of the immobilized IgG (i.e., the orientation of the immobilized IgG). The introduction of COOH promoted a more active orientation of the immobilized IgG. The orientation was determined during the adsorption process onto the azopolymer surface in solution before photo-immobilization, and was maintained during the photo-immobilization. The surface charge of the azopolymer appears to be an important factor for IgG orientation, which involves electrostatic interactions between its Fab and the azopolymer surface.

Molecular scale imaging of F-actin assemblies immobilized on a photopolymer surface.

A photo-immobilization based process is presented for direct imaging of hierarchical assemblies of biopolymers using atomic force microscopy (AFM). The technique was used to investigate the phase behavior of F-actin aggregates as a function of concentration of the divalent cation Mg2+. The data provided direct experimental evidence of a coil-on-coil (braided) structure of F-actin bundles formed at high Mg2+ concentrations. At intermediate Mg2+ concentrations, the data showed the first images of the two-dimensional nematic rafts discovered by recent x-ray studies and theoretical treatments.

Molecular-shape imprinting and immobilization of biomolecules on a polymer containing azo dye.

We demonstrate a novel technique for molecular imprinting and immobilization on a surface of a polymer containing azo dyes (azopolymer). The azopolymer was found to be capable of immobilizing micrometer- and nanometer-scale macromolecules (e.g., lambda-DNA, immunoglobulin G (IgG), bacterial protease, and 1-mum polystyrene particles) through photoirradiation with blue-wavelength light. Fluorescence and atomic force microscopy studies revealed that the azopolymer surface deformed along with the shape of the macromolecules, holding them in place after photoirradiation. The desorption of the immobilized macromolecules from the azopolymer surface in an aqueous medium was observed to be very slow, on the time scale of 10 min to weeks, depending on the photoirradiation time. Immunological and enzymatic studies showed that IgG and bacterial protease immobilized on the azopolymer surface retained their original functionality. These results suggest that the azopolymer physically, not chemically, binds the macromolecules because of the increase in contact area between the macromolecules and the azopolymer surface after photoirradiation.

Thermally stable and hydrogen peroxide tolerant manganese peroxidase (MnP) from Lenzites betulinus.

A thermally stable and hydrogen peroxide tolerant manganese peroxidase (MnP) was purified from the culture medium of Lenzites betulinus by ion exchange chromatography, gel filtration and isoelectric focusing chromatography. The MnP purified from L. betulinus (L-MnP) has a molecular mass of 40 kDa and its isoelectric point was determined to be 6.2. The first 19 amino acids at the N-terminal end of the L-MnP sequence were found to exhibit 74% identity with those of a Phlebia radiata MnP. L-MnP was proved to have the highest hydrogen peroxide tolerance among MnPs reported so far. It retained more than 60% of the initial activity after thermal treatment at 60 degrees C for 60 min, and also retained more than 60% of the initial activity after exposure to 10 mM hydrogen peroxide for 5 min at 37 degrees C.