Hot Deformation Behavior and Dynamic Softening Mechanism in 7B50 Aluminum Alloy.

The hot deformation behavior and dynamic softening mechanism of 7B50 aluminum alloy were studied via isothermal compression experiments in the range of 320-460 °C/0.001-1.0 s-1. According to the flow curves obtained from the experiments, the flow behavior of this alloy was analyzed, and the Zener-Hollomon (Z) parameter equation was established. The hot processing maps of this alloy were developed based on the dynamic material model, and the optimal hot working region was determined to be 410-460 °C/0.01-0.001 s-1. The electron backscattered diffraction (EBSD) microstructure analysis of the deformed sample shows that the dynamic softening mechanism and microstructure evolution strongly depend on the Z parameter. Meanwhile, a correlation between the dynamic softening mechanism and the lnZ value was established. Dynamic recovery (DRV) was the only softening mechanism during isothermal compression with lnZ ≥ 20. Discontinuous dynamic recrystallization (DDRX) becomes the dominant dynamic recrystallization (DRX) mechanism under deformation conditions of 15 < lnZ < 20. Meanwhile, the size and percentage of DDRXed grains increased with decreasing lnZ values. The geometric dynamic recrystallization (GDRX) mechanism and continuous dynamic recrystallization (CDRX) mechanism coexist under deformation conditions with lnZ ≤ 15.

A Modified Constitutive Model and Microstructure Characterization for 2195 Al-Li Alloy Hot Extrusion.

The quality of extruded profiles depends largely on accurate constitutive models and thermal processing maps. In this study, a modified Arrhenius constitutive model for homogenized 2195 Al-Li alloy with multi-parameter co-compensation was developed and further enhanced the prediction accuracy of flow stresses. Through the processing map and microstructure characterization, the 2195 Al-Li alloy could be deformed optimally at the temperature range of 710~783 K and strain rate of 0.001~0.12 s-1, preventing the occurrence of local plastic flow and abnormal growth of recrystallized grains. The accuracy of the constitutive model was verified through numerical simulation of 2195 Al-Li alloy extruded profiles with large shaped cross-sections. Dynamic recrystallization occurred at different regions during the practical extrusion process, resulting in slight variations in the microstructure. The differences in microstructure were due to the varying degrees of temperature and stress experienced by the material in different regions.

Improving Precipitation in Cryogenic Rolling 6016 Aluminum Alloys during Aging Treatment.

This study systematically investigated the performance and microstructure characterization of cryogenic rolling (CR) and room-temperature rolling (RTR) Al-Mg-Si alloys. The result showed that the hardness of the CR alloys decreased at the early aging stage, but that the hardness of the RTR alloys increased at the early aging stage. Retrogression phenomena were apparent in the CR alloys at the early aging stage. Despite undergoing the same solid solution treatment, a few substructures were still observed in the CR alloys, and the degree of recrystallization in the CR alloys was significantly inferior to that in the RTR alloys. After aging for 50 h, the strength and precipitates' density in the CR 75 alloy were higher than that in the other alloys; this indicated that the substructures were beneficial to precipitation and precipitate growth. A precipitation strength model was employed to illustrate the precipitation contribution at different aging stages. The results showed that the CR 75 alloy obtained the strongest precipitation strengthening.

Metagenomic evidence for antibiotics-driven co-evolution of microbial community, resistome and mobilome in hospital sewage.

Overconsumption of antibiotics is an immediate cause for the emergence of antimicrobial resistance (AMR) and antibiotic resistant bacteria (ARB), though its environmental impact remains inadequately clarified. There is an urgent need to dissect the complex links underpinning the dynamic co-evolution of ARB and their resistome and mobilome in hospital sewage. Metagenomic and bioinformatic methods were employed to analyze the microbial community, resistome and mobilome in hospital sewage, in relation to data on clinical antibiotic use collected from a tertiary-care hospital. In this study, resistome (1,568 antibiotic resistance genes, ARGs, corresponding to 29 antibiotic types/subtypes) and mobilome (247 types of mobile genetic elements, MGEs) were identified. Networks connecting co-occurring ARGs with MGEs encompass 176 nodes and 578 edges, in which over 19 types of ARGs had significant correlations with MGEs. Prescribed dosage and time-dependent antibiotic consumption were associated with the abundance and distributions of ARGs, and conjugative transfer of ARGs via MGEs. Variation partitioning analyses show that effects of conjugative transfer were most likely the main contributors to transient propagation and persistence of AMR. We have presented the first evidence supporting idea that use of clinical antibiotics is a potent driving force for the development of co-evolving resistome and mobilome, which in turn supports the growth and evolution of ARB in hospital sewage. The use of clinical antibiotics calls for greater attention in antibiotic stewardship and management.

Loss of erm(B)-Mediated rRNA Dimethylation and Restoration of Erythromycin Susceptibility in Erythromycin-Resistant Enterococci Following Induced Linezolid Resistance.

Linezolid has been reported to restore erythromycin susceptibility in erythromycin-resistant Staphylococcus aureus. This phenomenon has not been reported in enterococci and the mechanisms involved therein are still unknown. The purpose of this study was to investigate the mechanisms involved and the effect of combining linezolid with erythromycin on erythromycin-resistant enterococci. Checkerboard techniques were used to determine drug interactions, and 12 of 14 isolates showed a synergistic effect between erythromycin and linezolid (fractional inhibitory concentration <0.5). We observed that the erm(B) gene, which encodes a dimethyltransferase responsible for erythromycin resistance, was expressed from transposon Tn1545 in the tested erythromycin-resistant enterococci. After exposure to linezolid, erm(B)-mediated rRNA dimethylation at A2071 could not be detected, and the erm(B) gene was lost following acquisition of erythromycin susceptibility. Thus, in conclusion, linezolid combined with erythromycin exerts a synergistic effect against erythromycin-resistant enterococci. Linezolid treatment suppressed erm(B)-mediated rRNA dimethylation at A2071, which could lead to loss of the erm(B) gene.

Hot Deformation Behavior and Simulation of Hot-Rolled Damage Process for Fine-Grained Pure Tungsten at Elevated Temperatures.

Fine-grained pure tungsten fabricated by a sol drying reduction low-temperature sintering method and hot isothermal compression tests were performed by using the Gleeble 3800 thermo mechanical simulator at deformation temperatures from 1273 K to 1473 K and strain rates from 0.001 s-1 to 1 s-1. In addition, the constitutive equation was established by least square method combined with the Zerilli-Armstrong model, and the hot deformation behavior was discussed. Moreover, based on constitutive equation, the influence of the rolling process and its parameters on temperature, strain, density and rolling force in the hot rolling process was investigated at elevated temperature by the finite element model (FEM). Furthermore, the form of rolling damage and its formation mechanism were analyzed. Results showed the grains of pure tungsten are dense, irregular polyhedral spherical and very fine, and the average grain size is about 5.22 µm. At a high strain rate, the flow stress increases rapidly with the increase in strain, while the stress-strain curve shows a flattening trend in the tested strain rate range with increasing temperature, and no flow stress peak exists, showing obvious dynamic recovery characteristics. Furthermore, the FEM simulation showed that compared with the rolling temperature, the reduction has a greater influence on the temperature, stress-strain field and its distribution. There are three kinds of damage in the hot rolling process: transverse cracks, longitudinal cracks and side cracks, which are attributed to the competition between additional stress caused by uneven deformation and material strength. Moreover, the control method of hot rolling defects had been preliminarily proposed. These results should be of relevance for the optimum design of the hot rolling process of pure tungsten.

Resistance traits and molecular characterization of multidrug-resistant Acinetobacter baumannii isolates from an intensive care unit of a tertiary hospital in Guangdong, southern China / Rasgos de resistencia y caracterización molecular de aislamientos multirresistentes de Acinetobacter baumannii de una unidad de cuidados intensivos de un hospital terciario en Guangdong, sur de China

Purpose: This study aims to characterize antimicrobial resistance (AMR) of all the non-duplicated Acinetobacter baumannii strains isolated from an intensive care unit in a tertiary hospital during the period of January 1 to December 31, 2015. Methods: A. baumannii (n = 95 strains) isolated from patients was subjected to antimicrobial susceptibility test (AST) by Vitek 2 Compact system to determine minimum inhibitory concentrations, followed by genotyping by enterobacterial repetitive intergenic consensus-PCR (ERIC-PCR). Resistance genes of interest were PCR amplified and sequenced. Results:All isolates were qualified as MDR, with a resistance rate of > 80% to 8 antimicrobials tested. In terms of beta-lactamase detection, the blaOXA23, blaTEM-1, and armA genes were detected frequently at 92.63%, 9 1.58%, and 88.42%, respectively. The metallo-β-lactamase genes blaIMP and blaVIM were undetected. Aph (3’)-I was detected in 82 isolates (86.32%), making it the most prevalent aminoglycoside-modifying enzyme (AMEs) encoding gene. In addition, ant (3″)-I was detected at 30.53%, while 26.32% of the strains harbored an aac (6')-Ib gene. ERIC-PCR typing suggested moderate genetic diversity among the isolates, which might be organized into 10 distinct clusters, with cluster A (n = 86 isolates or 90.53%) being the dominant cluster. Conclusions: All of the A. baumannii strains detected in the ICU were MDR clones exhibiting extremely high resistance to carbapenems and aminoglycosides as monitored throughout the study period. They principally belonged to a single cluster of isolates carrying blaOXA23 and armA co-producing different AMEs genes.(AU)

Comparison of One-Stage and Two-Stage Intraoperative Uterine Artery Embolization during Cesarean Delivery for Placenta Accreta: Report of Two Clinical Cases at a Tertiary Referral Medical Center.

Placenta accreta spectrum (PAS) described the anchoring placental villi attached or penetrating into/through the myometrium. PAS is clinically important because of the unpredictable bleeding amount when manually removing the defective decidualization at the endometrial-myometrial interface. Therefore, a multidisciplinary strategy for cesarean delivery with PAS is crucial. Postoperative embolization after cesarean hysterectomy in a hybrid suite was studied by many scientists. In this study, we demonstrated two cases of intraoperative embolization without hysterectomy in a hybrid operating room for cesarean delivery with placenta accreta. Our results show that intraoperative uterine artery embolization with a hybrid suite is a time-preserving and safe method for cesarean delivery with PAS owing to avoiding the risk of morbidity and mortality during patient transfer.

Resistance traits and molecular characterization of multidrug-resistant Acinetobacter baumannii isolates from an intensive care unit of a tertiary hospital in Guangdong, southern China.

PURPOSE: This study aims to characterize antimicrobial resistance (AMR) of all the non-duplicated Acinetobacter baumannii strains isolated from an intensive care unit in a tertiary hospital during the period of January 1 to December 31, 2015. METHODS: A. baumannii (n = 95 strains) isolated from patients was subjected to antimicrobial susceptibility test (AST) by Vitek 2 Compact system to determine minimum inhibitory concentrations, followed by genotyping by enterobacterial repetitive intergenic consensus-PCR (ERIC-PCR). Resistance genes of interest were PCR amplified and sequenced. RESULTS: All isolates were qualified as MDR, with a resistance rate of > 80% to 8 antimicrobials tested. In terms of beta-lactamase detection, the blaOXA23, blaTEM-1, and armA genes were detected frequently at 92.63%, 9 1.58%, and 88.42%, respectively. The metallo-ß-lactamase genes blaIMP and blaVIM were undetected. Aph (3')-I was detected in 82 isolates (86.32%), making it the most prevalent aminoglycoside-modifying enzyme (AMEs) encoding gene. In addition, ant (3″)-I was detected at 30.53%, while 26.32% of the strains harbored an aac (6')-Ib gene. ERIC-PCR typing suggested moderate genetic diversity among the isolates, which might be organized into 10 distinct clusters, with cluster A (n = 86 isolates or 90.53%) being the dominant cluster. CONCLUSIONS: All of the A. baumannii strains detected in the ICU were MDR clones exhibiting extremely high resistance to carbapenems and aminoglycosides as monitored throughout the study period. They principally belonged to a single cluster of isolates carrying blaOXA23 and armA co-producing different AMEs genes.

Effect of multidisciplinary team care on survival of oesophageal cancer patients: a retrospective nationwide cohort study.

Oesophageal cancer is the sixth leading cause of cancer death worldwide. This nationwide study analyses the survival results of oesophageal cancer under multidisciplinary team (MDT) care. We enrolled oesophageal cancer patients diagnosed between 2010 and 2015 with follow-up for at least 1 year. This study performed propensity score matching with a ratio of 1:1 between MDT participants and non-MDT participants. We performed conditional Cox proportional hazards model to research relative risk of survival and associated factors of survival. The adjusted survival curves were plotted. 8184 newly diagnosed oesophageal cancer patients were included. The favourable survival factors include participant status of MDT, gender, monthly salary, urbanization level, other catastrophic illness, stage of cancer, treatment methods, and service volume of physicians (P < 0.05). MDT participants showed lower risk of death (HR = 0.73; 95% CI 0.67-0.79). Further stratification analysis revealed that the incorporation of an MDT reduced the death risk of patients with stages 2, 3, and 4 cancer, with the greatest reduction observed in patients with stage 3 cancer (HR = 0.72; 95% CI 0.67-0.79). The risk of death was lower for oesophageal cancer patients who enrolled in MDT care.

A comparative study on heterogeneous nucleation and mechanical properties of the fcc-Al/L12-Al3M (M = Sc, Ti, V, Y, Zr, Nb) interface from first-principles calculations.

In this work, we report a comparative study of the interfacial properties of fcc-Al/L12-Al3M (M = Sc, Ti, V, Y, Zr, Nb) from first-principles calculations. It is found that the fcc-Al(111)/L12-Al3Nb(111) interface is energetically favorable because of its negative interfacial energy (-0.225 J m-2), whereas the interfacial energies of the other five interfaces are positive. Despite their thermodynamically unfavorable characteristics, the stabilities of the formed interfaces are ranked in the order fcc-Al(111)/L12-Al3Nb(111) > fcc-Al(111)/L12-Al3Ti(111) > fcc-Al(111)/L12-Al3Zr(111) > fcc-Al(111)/L12-Al3Sc(111) > fcc-Al(111)/L12-Al3V(111) > fcc-Al(111)/L12-Al3Y(111). Moreover, the computed generalized stacking fault energy curves revealed that the (111)[11-2] slip system is preferred over the (111)[10-1] slip system under external stresses for all six interfaces. Based on the Rice ratio criterion, the interface slips also energetically favor the generation of stacking faults instead of cleavage for these interface systems; this finding implied that these interfaces did not greatly influence the plastic deformation behavior of aluminum. Furthermore, the derived bulk elastic properties indicate that fcc-Al, L12-Al3Nb, and L12-Al3V tend to present ductile behavior, while L12-Al3Zr, L12-Al3Ti, L12-Al3Y, and L12-Al3Sc are found to be brittle compounds. Nevertheless, all of these intermetallics can strengthen the aluminum matrix without losing much plasticity to provide a higher elastic modulus than aluminum along with the ductile interface nature of fcc-Al(111)/L12-A13M(111).

ROP and ATRP fabricated redox sensitive micelles based on PCL-SS-PMAA diblock copolymers to co-deliver PTX and CDDP for lung cancer therapy.

Combining dual drugs in one vehicle to cancer cells offers spatiotemporal localization of drug at the site of action, leading to synergistic therapeutic effects and reduced side effects. To improve pH/redox responsiveness to the tumor microenvironments for cancer therapy, a pH/redox-responsive micelle based on poly(ε-caprolactone)-SS-poly(methacrylic acid) (PCL-SS-PMAA) diblock copolymer was fabricated for dual drug delivery. The PCL-SS-PMAA was formulated into a core-shell micelle (PSPm) in an aqueous solution. The critical micelle concentration (CMC) values of PSPm were 7.94 × 10-3 mg mL-1 at pH 5.0 and 1.00 × 10-2 mg mL-1 at pH 7.4. The hydrodynamic diameters of PSPm were within 210-270 nm, depending on pH values. Changes in morphology and size of PSPm were clearly observed before and after exposure to a reducing agent. Paclitaxel (PTX) was encapsulated into the core and cisplatin (CDDP) was chelated on the shell of PSPm, with both PTX and CDDP being efficiently released from PSPm in the presence of a reducing agent in an acid condition. MTT and annexin V/propidium iodide dual staining results demonstrated that co-loading of CDDP and PTX into PSPm had a synergistic effect in killing lung cancer cells and exerted superior antitumor activity over the combination of single drug-loaded PSPm or the combination of free-CDDP and free-PTX at equivalent drug amounts. Hence, encapsulating the dual drugs into PSPm exhibits a synergistic effect for potential lung cancer therapy.

Multi-Stimuli-Responsive DOX Released from Magnetosome for Tumor Synergistic Theranostics.

BACKGROUND: To improve responses to tumor microenvironments for achieving a better therapeutic outcome in combination cancer therapy, poly(ε-caprolactone)-SS-poly(methacrylic acid) diblock copolymer (PCL-SS-PMAA) with a disulfide linkage between the hydrophobic and hydrophilic junctions was synthesized. MATERIALS AND METHODS: Repeating units of PCL and PMAA in PCL-SS-PMAA were controlled and formulated into polymersomes (PSPps). Truncated octahedral Fe3O4 nanoparticles (IONPs) were synthesized and encapsulated to produce IONPs-PSPps NPs and doxorubicin (DOX) was further loaded to produce IONPs-PSPps@DOX NPs for theranostic applications. RESULTS: IONPs-PSPps NPs remained a superparamagnetic property with a saturation magnetization value of 85 emu⋅gFe3O4 -1 and a relaxivity value of 180 mM-1⋅s-1. Upon exposure to an alternating magnetic field (AMF), IONPs-PSPps NPs increased temperature from 25°C to 54°C within 15 min. Among test groups, the cell apoptosis was greatest in the group exposed to IONPs-PSPps@DOX NPs with AMF and magnet assistance. In vivo T2-weighted magnetic resonance images of A549 tumor-bearing mice also showed highest contrast and greatest tumor suppression in the tumor with AMF and magnet assistance. CONCLUSION: IONPs-PSPps@DOX NPs are a potential theranostic agent having multifaceted applications involving magnetic targeting, MRI diagnosis, hyperthermia and chemotherapy.

Co-existence of Citrobacter freundii exacerbated Pseudomonas aeruginosa infection in vivo.

The presence of bacterial species other than the pathogen at infection site can affect the progression of a bacterial infection. Based on the fact that Citrobacter freundii can coexist during Pseudomonas aeruginosa infection, this study aims to investigate the impact of the co-existing C. freundii on the pathogenesis of P. aeruginosa infection. A murine peritonitis model was used to compare the mortality rates and histopathology of P. aeruginosaPAO1 infection in the presence and absence of a C. freundii clinical isolate C9. We also investigated the intercellular interaction between PAO1 and C9 by examining pyocyanin production and comparing gene expression levels. The results demonstrate that co-infection with C9 significantly increased the mortality rate and tissue damages in PAO1 infected mice. At an inoculum of 106 CFU, no mortality was observed in the C9 infected group at three days post-infection, whereas the mortality rate in the PAO1-C9 co-infection group was 64%, compared with 24% in the PAO1 infected group. Pyocyanin production in P. aeruginosa PAO1 increased 8 folds approximately in the presence of C. freundii C9, and operons associated with phenazine synthesis, phzA1 and phzA2, were also upregulated. Disruption of the phzA1 and phzA2 eliminated the exacerbated pathogenicity in the co-infection group, indicating that the elevated pyocyanin production was the main contributing factor. The results suggest that co-existing C. freundii during P. aeruginosa infection can exacerbate the pathogenicity, which may have significant implications in patients infected with these bacteria.

Effect of diabetes mellitus on risk of latent TB infection in a high TB incidence area: a community-based study in Taiwan.

OBJECTIVE: To investigate the association between diabetes and latent tuberculosis infections (LTBI) in high TB incidence areas. DESIGN: Community-based comparison study. SETTING: Outpatient diabetes clinics at 4 hospitals and 13 health centres in urban and rural townships. A community-based screening programme was used to recruit non-diabetic participants. PARTICIPANTS: A total of 2948 patients with diabetes aged older than 40 years were recruited, and 453 non-diabetic participants from the community were enrolled. PRIMARY AND SECONDARY OUTCOME MEASURES: The interferon-gamma release assay (IGRA) and the tuberculin skin test were used to detect LTBI. The IGRA result was used as a surrogate of LTBI in logistic regression analysis. RESULTS: Diabetes was significantly associated with LTBI (adjusted OR (aOR)=1.59; 95% CI 1.11 to 2.28) and age correlated positively with LTBI. Many subjects with diabetes also had additional risk factors (current smokers (aOR=1.28; 95% CI 0.95 to 1.71), comorbid chronic kidney disease (aOR=1.26; 95% CI 1.03 to 1.55) and history of TB (aOR=2.08; 95% CI 1.19 to 3.63)). The presence of BCG scar was protective (aOR=0.66; 95% CI 0.51 to 0.85). Duration of diabetes and poor glycaemic control were unrelated to the risk of LTBI. CONCLUSION: There was a moderately increased risk of LTBI in patients with diabetes from this high TB incidence area. This finding suggests LTBI screening for the diabetics be combined with other risk factors and comorbidities of TB to better identify high-risk groups and improve the efficacy of targeted screening for LTBI.

Co-segregation behavior of Sc and Zr solutes and their effect on the Al Σ5 (210) [110] symmetrical tilt grain boundary: a first-principles study.

The research into the co-segregation behavior of Sc and Zr solutes and their effect on the mechanical properties of the Al Σ5 (210) [110] grain boundary was carried out by first principles calculations. It is concluded that Sc and Zr both have a powerful driving force to segregate to the grain boundary, and based on the most negative segregation energy, first one Sc atom segregates to the grain boundary, then one Zr atom and finally another Sc atom. The grain boundary energy, strengthening/embrittling energy, fracture energy and theoretical tensile peak stress all demonstrate that Sc and Zr solutes have a strengthening effect on the grain boundary, which can be attributed to the combination of the "chemical effect" (charge density variation) and the "structural effect" (atomic arrangement change), especially the migration of the first Sc-segregated site toward the grain boundary, which not only brings stronger Sc/Zr-Al bonds instead of weak Al-Al bonds but also leads to the shrinkage and charge accumulation of the great vacuum area between two grains. This work sheds light on the underlying mechanism of the better mechanical performance due to the co-addition of Sc and Zr solutes at the atomic and electronic levels.

YhjX Regulates the Growth of Escherichia coli in the Presence of a Subinhibitory Concentration of Gentamicin and Mediates the Adaptive Resistance to Gentamicin.

The mechanisms of adaptive resistance of Escherichia coli to aminoglycosides remain unclear. Our RNA-Seq study found that expression of yhjX was markedly upregulated during initial exposure to subinhibitory concentrations of gentamicin. The expression of yhjX was then downregulated dramatically during a second exposure to gentamicin compared to the first exposure. YhjX encodes a putative transporter of the major facilitator superfamily, which is known to be the sole target of the YpdA/YpdB two-component system, the expression of which is highly and specifically induced by pyruvate. To investigate the effect of yhjX on the adaptive resistance of E. coli, in the present study, we constructed yhjX deletion and complemented strains of E. coli ATCC25922. Changes in extracellular pyruvate levels of wide-type and yhjX mutant were measured to determine whether YhjX functions as a pyruvate transporter. The results showed that yhjX deletion improved the growth of E. coli in medium containing subinhibitory concentrations of gentamicin. The yhjX deletion mutant did not exhibit adaptive resistance to subinhibitory concentrations of gentamicin. YhjX might not function as a pyruvate efflux pump in E. coli but was associated with the decrease following a sharp increase in the extracellular pyruvate level. Our findings indicate that yhjX regulates the growth of E. coli in the presence of a subinhibitory concentration of gentamicin and mediates the adaptive resistance to gentamicin.

Accuracy of point-of-care ultrasound and radiology-performed ultrasound for intussusception: A systematic review and meta-analysis.

OBJECTIVE: It is unclear whether point-of-care ultrasound (POCUS) by emergency medicine physicians is as accurate as radiology-performed ultrasound (RADUS). We aim to summarize the diagnostic accuracy of ultrasonography for intussusception and to compare the performance between POCUS and RADUS. METHODS: Databases were searched from inception through February 2018 using pre-defined index terms. Peer-reviewed primary studies that investigated the diagnostic accuracy of ultrasound for intussusception in children were included. The study is reported using Preferred Reporting Items for a Systematic Review and Meta-analysis of Diagnostic Test Accuracy Studies (PRISMA-DTA). Meta-analysis of the diagnostic accuracy of ultrasound for intussusception was conducted using the random-effects bivariate model. Subgroup analysis (POCUS vs RADUS) was also performed. Meta-regression was utilized to determine if the diagnostic accuracy between POCUS and RADUS was significantly different. RESULTS: Thirty studies (n = 5249) were included in the meta-analysis. Ultrasonography for intussusception has a sensitivity: 0.98 (95% CI: 0.96-0.98), specificity: 0.98 (95% CI: 0.95-0.99), positive likelihood ratio: 43.8 (95% CI: 18.0-106.7) and negative likelihood ratio: 0.03 (95% CI: 0.02-0.04), with an area under ROC (AUROC) curve of 0.99 (95% CI: 0.98-1.00). Meta-regression suggested no significant difference in the diagnostic accuracy for intussusception between POCUS and RADUS (AUROC: 0.95 vs 1.00, p = 0.128). CONCLUSIONS: Current evidence suggested POCUS has a high diagnostic accuracy for intussusception not significantly different from that of RADUS.

Functional near-infrared spectroscopy in the evaluation of urban rail transit drivers' mental workload under simulated driving conditions.

The objective of this study is to investigate the potential of functional near-infrared spectroscopy (fNIRS) combined with heart rate variability indices, for the evaluation of the mental workload of urban rail transit drivers under simulated driving conditions, particularly during task engagement and disengagement. Experienced metro drivers wearing fNIRS monitoring systems were asked to drive for 90 min in a professional metro driving simulator. Workload stimulus tasks were added and an n-back task (n = 3) was implemented to induce workload in the simulated driving experiment. Experimental results indicate that fNIRS are sensitive to mental workload and reliable for discriminating the degree of mental workload. Research findings demonstrate the feasibility and reliability of fNIRS as a tool for real-time evaluating and monitoring driver mental workload along with task factors from a perspective of brain activations during simulated or actual driving. Practitioner Summary: This study provides evidence for the potential of functional near-infrared spectroscopy (fNIRS) for the evaluation of the mental workload of urban rail transit drivers under simulated driving conditions. The first fNIRS application to mental workload evaluation in the field of urban rail transportation helps companies develop reasonable shiftwork schedule and ensure operation safety. Abbreviations: fNIRS: functional near-infrared spectroscopy; oxy-Hb: Oxy-hemoglobin; NASA-TLX: National Aeronautics and Space Administration Task Load Index; EEG: electroencephalogram; ECG: electrocardiogram; HRV: variability; LF: low-frequency power; HF: high-frequency power; PFC: prefrontal cortex; NIRS: near-infrared spectroscopy; DWT: discrete wavelet transform; EMG: electromyography; DT: determination test; TP: total power; LFnorm: standardized LF; HFnorm: standardized HF; VLF: very low frequency; deoxy-Hb: deoxy-hemoglobin.