Increasing the Sodium Metal Electrode Compatibility with the Na3 PS4 Solid-State Electrolyte through Heteroatom Substitution.

Rechargeable batteries are essential to the global shift towards renewable energy sources and their storage. At present, improvements in their safety and sustainability are of great importance as part of global sustainable development goals. A major contender in this shift are rechargeable solid-state sodium batteries, as a low-cost, safe, and sustainable alternative to conventional lithium-ion batteries. Recently, solid-state electrolytes with a high ionic conductivity and low flammability have been developed. However, these still face challenges with the highly reactive sodium metal electrode. The study of these electrolyte-electrode interfaces is challenging from a computational and experimental point of view, but recent advances in molecular dynamics neural-network potentials are finally enabling access to these environments compared to more computationally expensive conventional ab-initio techniques. In this study, heteroatom-substituted Na3 PS3 X1 analogues, where X is sulfur, oxygen, selenium, tellurium, nitrogen, chlorine, and fluorine, are investigated using total-trajectory analysis and neural-network molecular dynamics. It was found that inductive electron-withdrawing and electron-donating effects, alongside differences in heteroatom atomic radius, electronegativity, and valency, influenced the electrolyte reactivity. The Na3 PS3 O1 oxygen analogue was found to have superior chemical stability against the sodium metal electrode, paving the way towards high-performance, long lifetime and reliable rechargeable solid-state sodium batteries.

Non-fluorinated non-solvating cosolvent enabling superior performance of lithium metal negative electrode battery.

The growth of dendrites on lithium metal electrodes is problematic because it causes irreversible capacity loss and safety hazards. Localised high-concentration electrolytes (LHCEs) can form a mechanically stable solid-electrolyte interphase and prevent uneven growth of lithium metal. However, the optimal physicochemical properties of LHCEs have not been clearly determined which limits the choice to fluorinated non-solvating cosolvents (FNSCs). Also, FNSCs in LHCEs raise environmental concerns, are costly, and may cause low cathodic stability owing to their low lowest unoccupied molecular orbital level, leading to unsatisfactory cycle life. Here, we spectroscopically measured the Li+ solvation ability and miscibility of candidate non-fluorinated non-solvating cosolvents (NFNSCs) and identified the suitable physicochemical properties for non-solvating cosolvents. Using our design principle, we proposed NFNSCs that deliver a coulombic efficiency up to 99.0% over 1400 cycles. NMR spectra revealed that the designed NFNSCs were highly stable in electrolytes during extended cycles. In addition, solvation structure analysis by Raman spectroscopy and theoretical calculation of Li+ binding energy suggested that the low ability of these NFNSCs to solvate Li+ originates from the aromatic ring that allows delocalisation of electron pairs on the oxygen atom.

Development, retainment, and assessment of the graphite-electrolyte interphase in Li-ion batteries regarding the functionality of SEI-forming additives.

Formation of a decent solid-electrolyte interphase (SEI) is recognized as an approach to improve the performance of lithium-ion batteries. SEI is a passivation layer generated on the anode during the initial cycles. Characteristics of the graphite SEI depend on the operational parameters, state of the anode, and the content of the electrolyte. Introducing reduction-type additives to the carbonate electrolytes has been one of the most practiced methods to generate an effective SEI on carbonous anodes. To track the role of additives in SEI evolution, first, we have presented a general review on what is currently understood about the SEI formation processes and the impacting parameters. In the second step, the most reported methods to study and analyze the functionality of the SEI-forming additives are classified. As the third part, different reduction-type additives are categorized, and their performances are comparatively reviewed.

Electrodeposition of Highly Porous Pt Nanoparticles Studied by Quantitative 3D Electron Tomography: Influence of Growth Mechanisms and Potential Cycling on the Active Surface Area.

Nanoporous Pt nanoparticles (NPs) are promising fuel cell catalysts due to their large surface area and increased electrocatalytic activity toward the oxygen reduction reaction (ORR). Herein, we report on the influence of the growth mechanisms on the surface properties of electrodeposited Pt dendritic NPs with large surface areas. The electrochemically active surface was studied by hydrogen underpotential deposition (H UPD) and compared for the first time to high-angle annular dark field scanning transmission electron microscopy (HAADF-STEM) quantitative 3D electron tomography of individual nanoparticles. Large nucleation overpotential leads to a large surface coverage of roughened spheroids, which provide a large roughness factor (Rf) but low mass-specific electrochemically active surface area (EASA). Lowering the nucleation overpotential leads to highly porous Pt NPs with pores stretching to the center of the structure. At the expense of smaller Rf, the obtained EASA values of these structures are in the range of those of large surface area supported fuel cell catalysts. The active surface area of the Pt dendritic NPs was measured by electron tomography, and it was found that the potential cycling in the H adsorption/desorption and Pt oxidation/reduction region, which is generally performed to determine the EASA, leads to a significant reduction of that surface area due to a partial collapse of their dendritic and porous morphology. Interestingly, the extrapolation of the microscopic tomography results in macroscopic electrochemical parameters indicates that the surface properties measured by H UPD are comparable to the values measured on individual NPs by electron tomography after the degradation caused by the H UPD measurement. These results highlight that the combination of electrochemical and quantitative 3D surface analysis techniques is essential to provide insights into the surface properties, the electrochemical stability, and, hence, the applicability of these materials. Moreover, it indicates that care must be taken with widely used electrochemical methods of surface area determination, especially in the case of large surface area and possibly unstable nanostructures, since the measured surface can be strongly affected by the measurement itself.

Emission Spectroscopic Boundary Layer Investigation during Ablative Material Testing in Plasmatron.

Ablative Thermal Protection Systems (TPS) allowed the first humans to safely return to Earth from the moon and are still considered as the only solution for future high-speed reentry missions. But despite the advancements made since Apollo, heat flux prediction remains an imperfect science and engineers resort to safety factors to determine the TPS thickness. This goes at the expense of embarked payload, hampering, for example, sample return missions. Ground testing in plasma wind-tunnels is currently the only affordable possibility for both material qualification and validation of material response codes. The subsonic 1.2MW Inductively Coupled Plasmatron facility at the von Karman Institute for Fluid Dynamics is able to reproduce a wide range of reentry environments. This protocol describes a procedure for the study of the gas/surface interaction on ablative materials in high enthalpy flows and presents sample results of a non-pyrolyzing, ablating carbon fiber precursor. With this publication, the authors envisage the definition of a standard procedure, facilitating comparison with other laboratories and contributing to ongoing efforts to improve heat shield reliability and reduce design uncertainties. The described core techniques are non-intrusive methods to track the material recession with a high-speed camera along with the chemistry in the reactive boundary layer, probed by emission spectroscopy. Although optical emission spectroscopy is limited to line-of-sight measurements and is further constrained to electronically excited atoms and molecules, its simplicity and broad applicability still make it the technique of choice for analysis of the reactive boundary layer. Recession of the ablating sample further requires that the distance of the measurement location with respect to the surface is known at all times during the experiment. Calibration of the optical system of the applied three spectrometers allowed quantitative comparison. At the fiber scale, results from a post-test microscopy analysis are presented.

A generalized electrochemical aggregative growth mechanism.

The early stages of nanocrystal nucleation and growth are still an active field of research and remain unrevealed. In this work, by the combination of aberration-corrected transmission electron microscopy (TEM) and electrochemical characterization of the electrodeposition of different metals, we provide a complete reformulation of the Volmer-Weber 3D island growth mechanism, which has always been accepted to explain the early stages of metal electrodeposition and thin-film growth on low-energy substrates. We have developed a Generalized Electrochemical Aggregative Growth Mechanism which mimics the atomistic processes during the early stages of thin-film growth, by incorporating nanoclusters as building blocks. We discuss the influence of new processes such as nanocluster self-limiting growth, surface diffusion, aggregation, and coalescence on the growth mechanism and morphology of the resulting nanostructures. Self-limiting growth mechanisms hinder nanocluster growth and favor coalescence driven growth. The size of the primary nanoclusters is independent of the applied potential and deposition time. The balance between nucleation, nanocluster surface diffusion, and coalescence depends on the material and the overpotential, and influences strongly the morphology of the deposits. A small extent of coalescence leads to ultraporous dendritic structures, large surface coverage, and small particle size. Contrarily, full recrystallization leads to larger hemispherical monocrystalline islands and smaller particle density. The mechanism we propose represents a scientific breakthrough from the fundamental point of view and indicates that achieving the right balance between nucleation, self-limiting growth, cluster surface diffusion, and coalescence is essential and opens new, exciting possibilities to build up enhanced supported nanostructures using nanoclusters as building blocks.

In situ study of the deposition of (ultra)thin organic phosphonic acid layers on the oxide of aluminum.

The interest in self-assembling monolayer deposition on various oxide substrate surfaces is steeply increasing in the last decades. Although many studies are being performed, literature does not come with a general insight in the adsorption of these layers on oxide surfaces. Also for the deposition of phosphonic acids on aluminum oxides, there is no global consensus. In this paper, we present an original in situ analysis in order to eludicate the real layer formation mechanism. First of all, the state of the phosphonic acid molecules was determined using DOSY NMR, making sure that no structures other than free molecules were present at the concentration used. With in situ atomic force microscopy and in situ visual ellipsometry, multilayers of phosphonic acids, showing 3D island growth, were determined. It was shown that using the variation of the in situ obtained roughness and bearing ratio, together with the equivalent thickness modeled by ellipsometry, the growth of the layers occurs in situ in three different stages. They consist of increasing number of islands growth, followed by filling up the gaps between islands. At last, within the adsorption time frame measured, the islands grow further in dimensions but not in numbers. This closely corresponds with the behavior of the octylphosphonic acid films analyzed by ex situ techniques.

Microbial dissolution of hematite and associated cellular fossilization by reduced iron phases: a study of ancient microbe-mineral surface interactions.

We report here on magnetite- and wustite-encrusted and geometrically oriented microbial-like structures (MLS) attached to the surfaces of hematite (alpha-Fe(2)O(3)) crystals in a banded iron formation. Field emission scanning electron microscope (FE-SEM) and scanning electron microscope (SEM) imaging showed a 3-D network of MLS arranged in 1 microm x approximately 20 microm coccoidal-like chains (CLC) of various geometrical shapes: dichotomous and budding-like protrusions, parallel, intersecting, triangular, or sinusoidal. Individual spheroidal forms ( approximately 1 mum in diameter), some displaying what appears to be division, were also abundant. In addition to their size, morphology, and preferred orientations, a microbial origin of these chains and single spheroidal forms is inferred by the presence of material that resembles extracellular polymeric substances (EPS) extending from the base of the chains along the mineral surface: the attachment sites show circular dissolution pits of about 100 nm diameter. Other thin structures protruding from the CLC are reminiscent of bacterial "nanowires." We were, however, unable to find any extant cells, organic carbon, or even recover DNA from the MLS, which suggests that they, if microbial, are possibly mineralogically replaced casts or mineral encrustations of cells. It is further speculated that, given the nature of the substrate upon which the forms are attached and their preferential orientations, it seems plausible that the "original cells" may have been Fe(III)-reducing bacteria that exploited structural imperfections in the crystal lattice. Importantly, the preservation of the ancient microbial shapes in mineral casts of magnetite, wustite, or both may be an overlooked means by which cellular features in the rock record are retained.

In situ control of the oxide layer on thermally evaporated titanium and lysozyme adsorption by means of electrochemical quartz crystal microbalance with dissipation.

Electrochemical (EC) quartz crystal microbalance with dissipation monitoring (ECQCM-D) is a new and powerful technique for the in situ study of adsorption phenomena, e.g., as a function of the potential of the substrate. When titanium (Ti) is employed as the substrate, its oxidation behavior needs to be taken into account. Ti is always covered with a native oxide layer that can grow by, e.g., thermal oxidation or under anodic polarization. For biomolecular adsorption studies on oxidized Ti under applied potential, a stable oxide layer is desired in order to be able to distinguish the adsorption phenomena and the oxide growth. Therefore, the oxidation of thermally evaporated Ti films was investigated in phosphate-buffered saline by means of ECQCM-D, using a specially designed EC flow cell. Upon stepping the potential applied to Ti up to 2.6 V vs standard hydrogen electrode (SHE), a fast increase of the mass was observed initially for each potential step, evolving slowly to an asymptotic mass change after several hours. The oxide layer thickness increased as a quasi-linear function of the oxidation potential for potentials up to 1.8 V vs SHE. The growth rate of the oxide was around 2.5-3 nm/V. No changes in the dissipation shift were observed for potentials up to 1.8 V vs SHE. The composition of the oxide layer was analyzed by X-ray photoelectron spectroscopy (XPS). It was mainly composed of TiO(2), with a small percentage of suboxides (TiO and Ti(2)O(3)) primarily at the inner metal/oxide interface. The amount of TiO(2) increased, and that of TiO and Ti(2)O(3) decreased, with increasing oxidation potential. For each oxidation potential, the calculated thickness obtained from ECQCM-D correlated well with the thickness obtained by XPS depth profiling. A procedure to prepare Ti samples with a stable oxide layer was successfully established for investigations on the influence of an electric field on the adsorption of biomolecules. As such, the effect of an applied potential on the adsorption behavior of lysozyme on oxidized Ti was investigated. It was observed that the adsorption of lysozyme on oxidized Ti was not influenced by the applied potential.

Study of the self-assembling of n-octylphosphonic acid layers on aluminum oxide.

The deposition of n-octylphosphonic acid on aluminum oxide was studied. The substrate was pretreated in order to achieve a root-mean-square roughness of <1 nm, a hydroxyl fraction of 30%, and a thickness of approximately 170 nm. It was proven using X-ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM) that, rather than a monolayer, an organic multilayer was formed. The growth mechanism was identified as a Stranski-Krastanov one. It was also shown that the use of AFM, probing the surface topography, is essential for a reliable quantification and interpretation of data obtained with XPS.

Interaction of human plasma fibrinogen with commercially pure titanium as studied with atomic force microscopy and X-ray photoelectron spectroscopy.

The surface of a biomaterial interacts with the body fluid upon implantation in the human body. The biocompatibility of a material is strongly influenced by the adsorption of proteins onto the surface. Titanium is frequently used as a biomaterial for implants in orthopedics and cardiovascular devices. Understanding the biocompatibility is very important to improve implants. The surface chemistry of an implant material and its influence on the interaction with body fluid is crucial in that perspective. The main goal of this study was to investigate the conformation of human plasma fibrinogen (HPF) adsorbed on commercially pure titanium (CP Ti) on a molecular level by means of ex situ atomic force microscopy (AFM). With X-ray photoelectron spectroscopy combined with argon ion beam depth profiling, it was shown that the oxide layer present at the surface was mainly composed of TiO2, with a small percentage of Ti2O3. Ex situ AFM imaging showed the conformation of HPF on CP Ti. Single molecules and aggregates of fibrinogen were observed. The trinodular structure of single HPF molecules (two spherical D domains at the distal ends of the extended molecule and the central spherical E domain) adsorbed onto CP Ti was visualized. Aggregate formation through the connection of the D domains of the HPF molecules was observed on CP Ti. The alphaC domains of HPF were not visible on CP Ti. The ex situ AFM images indicated conformational changes of HPF upon adsorption onto CP Ti. The conformation of the adsorbed HPF molecules was different on mica and titanium. The difference in wettability between both substrates caused a larger spread of the protein on the CP Ti surface and thus resulted in a larger perturbation to the native structure of HPF as compared to mica.

Study of the affinity of thermographic additives for silver by time-of-flight static secondary ion mass spectrometry and surface-enhanced Raman spectroscopy on silver nanoparticles.

Detection of the interactions between low molecular weight organic compounds and metals in the form of sols on a nanoscale is analytically challenging. This study aims to provide experimental evidence using a combination of UV-Vis absorption spectrometry, surface-enhanced Raman spectrometry (SERS), and static secondary ion mass spectrometry (S-SIMS). The field of application is thermography where silver images are formed via heat-catalyzed reactions. Several organic compounds called tone modifiers and stabilizers are used in thermographic materials for the optimization of the image quality. With exploitation of the strengths of each of the above-mentioned methods, an affinity ranking of several tone modifiers and a stabilizer was established on the basis of competitive adsorption experiments using different model systems. Specifically, silver sols, SERS probes, and sputter-coated silver substrates were exposed to systems with one or two additives. The UV-Vis results provided insight on the aggregation of silver nanoparticles in a hydrosol, which was necessary for the interpretation of the SERS data. Both SERS and S-SIMS measurements led to a similar ranking of the relative affinity of the additives in two components, which was largely consistent with empirical knowledge derived from macroscopic behavior.

Micro Raman spectroscopy used for the study of corrosion products on copper alloys: study of the chemical composition of artificial patinas used for restoration purposes.

Studying the atmospheric corrosion of copper alloy artifacts is important to acquire a better knowledge about the condition of the object and its possible conservation and restoration. The nature of the formed product, e.g. sulfate, carbonate or chloride, depends on factors such as the amount of polluting elements or humidity but may also depend on the nature of the underlying aesthetic patina, applied by the artist. The composition of the patination solution and the method of patination will both influence the nature of this aesthetic patina, i.e. its chemical composition and morphology. However, although a lot of patination recipes exist, little is known about these patinas as far as composition, structure and ageing is concerned. Therefore, a combination of several surface analytical techniques is required for the complete characterization of patina layers. In this paper, Raman spectroscopy is used to study the characteristics of several patinas obtained on copper following different traditional recipes.