Studying crystallisation processes using electron microscopy: The importance of sample preparation.

We present a comparison of common electron microscopy sample preparation methods for studying crystallisation processes from solution using both scanning and transmission electron microscopy (SEM and TEM). We focus on two widely studied inorganic systems: calcium sulphate, gypsum (CaSO4·2H2O) and calcium carbonate (CaCO3). We find significant differences in crystallisation kinetics and polymorph selection between the different sample preparation methods, which indicate that drying and chemical quenching can induce severe artefacts that are capable of masking the true native state of the crystallising solution. Overall, these results highlight the importance of cryogenic (cryo)-quenching crystallising solutions and the use of full cryo-TEM as the most reliable method for studying the early stages of crystallisation.

Structure of polymeric nanoparticles encapsulating a drug - pamoic acid ion pair by scanning transmission electron microscopy.

Drug-delivery systems based on polymeric nanoparticles are useful for improving drug bioavailability and/or delivery of the active ingredient for example directly to the cancerous tumour. The physical and chemical characterization of a functionalized nanoparticle system is required to measure drug loading and dispersion but also to understand and model the rate and extent of drug release to help predict performance. Many techniques can be used, however, difficulties related to structure determination and identifying the precise location of the drug fraction make mathematical prediction complex and in many published examples the final conclusions are based on assumptions regarding an expected structure. Cryogenic scanning transmission electron microscopy imaging in combination with electron energy loss spectroscopy techniques are used here to address this issue and provide a multi-modal approach to the characterisation of a self-assembled polymeric nanoparticle system based upon a polylactic acid - polyethylene glycol (PLA-PEG) block copolymer containing a hydrophobic ion-pair between pamoic acid and an active pharmaceutical ingredient (API). Results indicate a regular dispersion of spherical nanoparticles of 88 ± 9 nm diameter. The particles are shown to have a multi-layer structure consisting of a 25 nm radius hydrophobic core of PLA and pamoic acid-API material with additional enrichment of the pamoic acid-API material within the inner core (that can be off-centre), surrounded by a 9 nm dense PLA-PEG layer all with a low-density PEG surface coating of around 10 nm thickness. This structure suggests that release of the API can only occur by diffusion through or degradation of the dense, 9 nm thick PLA-PEG layer either of which is a process consistent with the previously reported steady release kinetics of the API and counter ion from these nanoparticle formulations. Establishing accurate measures of product structure enables a link to performance by providing appropriate physical parameters for future mathematical modelling of barriers controlling API release in these nanoparticle formulations.

Electron transparent nanotubes reveal crystallization pathways in confinement.

The cylindrical pores of track-etched membranes offer excellent environments for studying the effects of confinement on crystallization as the pore diameter is readily varied and the anisotropic morphologies can direct crystal orientation. However, the inability to image individual crystals in situ within the pores in this system has prevented many of the underlying mechanisms from being characterized. Here, we study the crystallization of calcium sulfate within track-etched membranes and reveal that oriented gypsum forms in 200 nm diameter pores, bassanite in 25-100 nm pores and anhydrite in 10 nm pores. The crystallization pathways are then studied by coating the membranes with an amorphous titania layer prior to mineralization to create electron transparent nanotubes that protect fragile precursor materials. By visualizing the evolutionary pathways of the crystals within the pores we show that the product single crystals derive from multiple nucleation events and that orientation is determined at early reaction times. Finally, the transformation of bassanite to gypsum within the membrane pores is studied using experiment and potential mean force calculations and is shown to proceed by localized dissolution/reprecipitation. This work provides insight into the effects of confinement on crystallization processes, which is relevant to mineral formation in many real-world environments.

Polyamines Promote Aragonite Nucleation and Generate Biomimetic Structures.

Calcium carbonate biomineralization is remarkable for the ability of organisms to produce calcite or aragonite with perfect fidelity, where this is commonly attributed to specific anionic biomacromolecules. However, it is proven difficult to mimic this behavior using synthetic or biogenic anionic organic molecules. Here, it is shown that cationic polyamines ranging from small molecules to large polyelectrolytes can exert exceptional control over calcium carbonate polymorph, promoting aragonite nucleation at extremely low concentrations but suppressing its growth at high concentrations, such that calcite or vaterite form. The aragonite crystals form via particle assembly, giving nanoparticulate structures analogous to biogenic aragonite, and subsequent growth yields stacked aragonite platelets comparable to structures seen in developing nacre. This mechanism of polymorph selectivity is captured in a theoretical model based on these competing nucleation and growth effects and is completely distinct from the activity of magnesium ions, which generate aragonite by inhibiting calcite. Profiting from these contrasting mechanisms, it is then demonstrated that polyamines and magnesium ions can be combined to give unprecedented control over aragonite formation. These results give insight into calcite/aragonite polymorphism and raise the possibility that organisms may exploit both amine-rich organic molecules and magnesium ions in controlling calcium carbonate polymorph.

Industrial-relevant TiO2 types do not promote cytotoxicity in the A549 or TK6 cell lines regardless of cell specific interaction.

Due to the expansive application of TiO2 and its variance in physico-chemical characteristics, the toxicological profile of TiO2, in all its various forms, requires evaluation. This study aimed to assess the hazard of five TiO2 particle-types in relation to their cytotoxic profile correlated to their cellular interaction, specifically in human lymphoblast (TK6) and type-II alveolar epithelial (A549) cells. Treatment with the test materials was undertaken at a concentration range of 1-100 µg/cm2 over 24 and 72 h exposure. TiO2 interaction with both cell types was visualised by transmission electron microscopy, supported by energy-dispersive X-ray. None of the TiO2 materials tested promoted cytotoxicity in either cell type over the concentration and time range studied. All materials were observed to interact with the A549 cells and were further noted to be internalised following 24 h exposure. In contrast, only the pigmentary rutile was internalised by TK6 lymphoblasts after 24 h exposure. Where uptake was observed there was no evidence, as determined by 2D microscopy techniques, of particle localisation within the nucleus of either cell type. This study indicates that industrially relevant TiO2 particles demonstrate cell interactions that are cell-type dependent and do not induce cytotoxicity at the applied dose range.

Analysis of complex, beam-sensitive materials by transmission electron microscopy and associated techniques.

We review the use of transmission electron microscopy (TEM) and associated techniques for the analysis of beam-sensitive materials and complex, multiphase systems in-situ or close to their native state. We focus on materials prone to damage by radiolysis and explain that this process cannot be eliminated or switched off, requiring TEM analysis to be done within a dose budget to achieve an optimum dose-limited resolution. We highlight the importance of determining the damage sensitivity of a particular system in terms of characteristic changes that occur on irradiation under both an electron fluence and flux by presenting results from a series of molecular crystals. We discuss the choice of electron beam accelerating voltage and detectors for optimizing resolution and outline the different strategies employed for low-dose microscopy in relation to the damage processes in operation. In particular, we discuss the use of scanning TEM (STEM) techniques for maximizing information content from high-resolution imaging and spectroscopy of minerals and molecular crystals. We suggest how this understanding can then be carried forward for in-situ analysis of samples interacting with liquids and gases, provided any electron beam-induced alteration of a specimen is controlled or used to drive a chosen reaction. Finally, we demonstrate that cryo-TEM of nanoparticle samples snap-frozen in vitreous ice can play a significant role in benchmarking dynamic processes at higher resolution. This article is part of a discussion meeting issue 'Dynamic in situ microscopy relating structure and function'.

Nanoparticle corona artefacts derived from specimen preparation of particle suspensions.

Progress in the implementation of nanoparticles for therapeutic applications will accelerate with an improved understanding of the interface between nanoparticle surfaces and the media they are dispersed in. We examine this interface by analytical scanning transmission electron microscopy and show that incorrect specimen preparation or analysis can induce an artefactual, nanoscale, calcium phosphate-rich, amorphous coating on nanoparticles dispersed in cell culture media. We report that this ionic coating can be induced on five different types of nanoparticles (Au, BaTiO3, ZnO, TiO2 and Fe2O3) when specimen preparation causes a significant rise in pH above physiological levels. Such a pH change reduces ionic solubility in the suspending media to permit precipitation of calcium phosphate. Finally, we demonstrate that there is no indication of a calcium-phosphorus-rich coating on BaTiO3 nanoparticles suspended in culture media when prepared without alteration of the pH of the suspending media and imaged by cryo-STEM. Therefore we recommend that future reports utilising nanoparticles dispersed in cell culture media monitor and report the pH of suspensions during sample preparation.

Cryo-analytical STEM of frozen, aqueous dispersions of nanoparticles.

In situ characterisation of nanoparticle dispersion and surface coatings is required to further our understanding of the behaviour of nanoparticles in aqueous suspension. Using cryogenic transmission electron microscopy (cryo-TEM) it is possible to analyse a nanoparticle suspension in the frozen, hydrated state; however, this analysis is often limited to imaging alone. This work demonstrates the first use of analytical scanning TEM (STEM) in the examination of nanoparticles captured in a layer of vitreous ice. Imaging and analysis of frozen hydrated suspensions by both STEM energy dispersive X-ray (EDX) spectroscopy and electron energy loss spectroscopy (EELS) under cryogenic conditions demonstrates the identification and separation of CeO2, Fe2O3, ZnO and Ag nanoparticles in suspension. Damage caused by the electron beam was shown to occur at far higher electron fluences in STEM (<2000 e-/Å2) compared to CTEM (<100 e-/Å2) due to diffusion limited damage by the radiolysis products generated in vitreous ice. Further application of cryo-analytical STEM was undertaken on barium titanate biomarker nanoparticles dispersed in cell culture media to show the formation of a Ca and P rich coating around the nanoparticles when suspended in the media. This previously unreported coating changes the surface chemistry of the biomarkers when exposed to cells. Thus we show that the technique has the potential to advance our understanding of the fundamental behaviour of nanoparticles in complex aqueous suspensions.

Toxicological findings in driver and motorcyclist fatalities in Scotland 2012-2015.

Fatal motor vehicle crashes (MVCs) continue to be a common occurrence worldwide. This paper presents a retrospective analysis of the toxicological investigation of drivers and motorcyclists fatally injured in MVCs in Scotland from 2012 to 2015. One hundred and eighteen cases with full toxicological analysis, i.e., alcohol, drugs of abuse and prescription drugs, were examined. Of those 118 MVC cases, 74 (63%) were car drivers, 32 (27%) were motorcyclists and the remaining were drivers of other vehicles such as large goods vehicles. The majority of deceased drivers and motorcyclists were male (N=104, 88%). For the toxicological findings, 51 (43%) of the cases were negative, and of the 67 (57%) positive cases, alcohol and cannabinoids were the most frequently detected substances, followed by opioids and benzodiazepines. Fifteen percent of all drivers and motorcyclists were over the prescribed blood alcohol limit at the time of analysis. In comparison to previous reports of drug use by drivers in Scotland, benzodiazepines and new psychoactive substances were less common findings in fatally injured drivers and motorcyclists than in drivers suspected of being impaired.