RESUMEN
Despite the importance of the stability of the 2D catalysts in harsh electrolyte solutions, most studies have focused on improving the catalytic performance of molybdenum disulfide (MoS2) catalysts rather than the sustainability of hydrogen evolution. In previous studies, the vulnerability of MoS2 crystals is reported that the moisture and oxygen molecules can cause the oxidation of MoS2 crystals, accelerating the degradation of crystal structure. Therefore, optimization of catalytic stability is crucial for approaching practical applications in 2D catalysts. Here, it is proposed that monolayered MoS2 catalysts passivated with an atomically thin hexagonal boron nitride (h-BN) layer can effectively sustain hydrogen evolution reaction (HER) and demonstrate the ultra-high current density (500 mA cmâ»2 over 11 h) and super stable (64 h at 150 mA cmâ»2) catalytic performance. It is further confirmed with density functional theory (DFT) calculations that the atomically thin h-BN layer effectively prevents direct adsorption of water/acid molecules while allowing the protons to be adsorbed/penetrated. The selective penetration of protons and prevention of crystal structure degradation lead to maintained catalytic activity and maximized catalytic stability in the h-BN covered MoS2 catalysts. These findings propose a promising opportunity for approaching the practical application of 2D MoS2 catalysts having long-term stability at high-current operation.
RESUMEN
Ferroelectric field-effect transistors (FeFETs) are increasingly important for in-memory computing and monolithic 3D (M3D) integration in system-on-chip (SoC) applications. However, the high-temperature processing required by most ferroelectric memories can lead to thermal damage to the underlying device layers, which poses significant physical limitations for 3D integration processes. To solve this problem, the study proposes using a nanosecond pulsed laser for selective annealing of hafnia-based FeFETs, enabling precise control of heat penetration depth within thin films. Sufficient thermal energy is delivered to the IGZO oxide channel and HZO ferroelectric gate oxide without causing thermal damage to the bottom layer, which has a low transition temperature (<250 °C). Using optimized laser conditions, a fast response time (<1 µs) and excellent stability (cycle > 106, retention > 106 s) are achieved in the ferroelectric HZO film. The resulting FeFET exhibited a wide memory window (>1.7 V) with a high on/off ratio (>105). In addition, moderate ferroelectric properties (2·Pr of 14.7 µC cm-2) and pattern recognition rate-based linearity (potentiation: 1.13, depression: 1.6) are obtained. These results demonstrate compatibility in HZO FeFETs by specific laser annealing control and thin-film layer design for various structures (3D integrated, flexible) with neuromorphic applications.
RESUMEN
Advancements in sensor technology have significantly enhanced atmospheric monitoring. Notably, metal oxide and carbon (MOx/C) hybrids have gained attention for their exceptional sensitivity and room-temperature sensing performance. However, previous methods of synthesizing MOx/C composites suffer from problems, including inhomogeneity, aggregation, and challenges in micropatterning. Herein, we introduce a refined method that employs a metal-organic framework (MOF) as a precursor combined with direct laser writing. The inherent structure of MOFs ensures a uniform distribution of metal ions and organic linkers, yielding homogeneous MOx/C structures. The laser processing facilitates precise micropatterning (< 2 µm, comparable to typical photolithography) of the MOx/C crystals. The optimized MOF-derived MOx/C sensor rapidly detected ethanol gas even at room temperature (105 and 18 s for response and recovery, respectively), with a broad range of sensing performance from 170 to 3,400 ppm and a high response value of up to 3,500%. Additionally, this sensor exhibited enhanced stability and thermal resilience compared to previous MOF-based counterparts. This research opens up promising avenues for practical applications in MOF-derived sensing devices.
RESUMEN
A nano vacuum tube which consists of a vacuum transistor and a nano vacuum chamber was demonstrated. For the device, a vacuum region is an electron transport channel, and a vacuum is a tunneling barrier. Tilted angle evaporation was studied for the formation of the nano level vacuum chamber structure. This vacuum tube was ultraminiaturized with several tens of 10-18 L scale volume and 10-6 Torr of pressure. The device structure made it possible to achieve a high integration density and to sustain the vacuum state in various real operations. In particular, the vacuum transistor performed stably in extreme external environments because the tunneling mechanism showed a wide range of working stability. The vacuum was sustained well by the sealing layer and provided a defect-free tunneling junction. In tests, the high vacuum level was maintained for more than 15 months with high reliability. The Al sealing layer and tube structure can effectively block exposed light such as visible light and UV, enabling the stable operation of the tunneling transistor. In addition, it is estimated that the structure blocks approximately 5 keV of X-ray. The device showed stable operating characteristics in a wide temperature range of 100-390 K. Therefore, the vacuum tube can be used in a wide range of applications involving integrated circuits while resolving the disadvantages of a large volume in old vacuum tubes. Additionally, it can be an important solution for next-generation devices in various fields such as aerospace, artificial intelligence, and THz applications.
RESUMEN
Purpose: This study aimed to investigate the involvement of patients who died from hematologic neoplasms in the decision-making process surrounding the withdrawal of life-sustaining treatment (LST). Methods: A total of 255 patients diagnosed with hematologic neoplasms who ultimately died following decisions related to LST during their end-of-life period at a university hospital were included in the study. Data were retrospectively obtained from electronic medical records and analyzed utilizing the chi-square test, independent t-test, and logistic regression. Results: In total, 42.0% of patients participated in the decision-making process regarding LST for their hematologic neoplasms, while 58.0% of decisions were made with family involvement. Among these patients, 65.1% died in general wards and 34.9% in intensive care units (ICUs) as a result of decisions such as the suspension of LST. The period from the LST decision to death was longer when the decision was made by the patient (average, 27.15 days) than when it was made by the family (average, 7.48 days). Most decisions were made by doctors and family members in the ICU, where only 20.6% of patients exercised their right to make decisions regarding LST, a rate considerably lower than 79.4% observed in general wards. Decisions to withhold or withdraw LST were more commonly made by patients themselves than by their families. Conclusion: The key to discussing the decision to suspend hospice care and LST is respecting the patient's self-determination. If a patient is lucid prior to admission to the ICU, considerations about suspending LST should involve the patient input.
RESUMEN
Due to rapid urbanization worldwide, monitoring the concentration of nitrogen dioxide (NO2), which causes cardiovascular and respiratory diseases, has attracted considerable attention. Developing real-time sensors to detect parts-per-billion (ppb)-level NO2 remains challenging due to limited sensitivity, response, and recovery characteristics. Herein, we report a hybrid structure of Cu3HHTP2, 2D semiconducting metal-organic frameworks (MOFs), and laser-induced graphene (LIG) for high-performance NO2 sensing. The unique hierarchical pore architecture of LIG@Cu3HHTP2 promotes mass transport of gas molecules and takes full advantage of the large surface area and porosity of MOFs, enabling highly rapid and sensitive responses to NO2. Consequently, LIG@Cu3HHTP2 shows one of the fastest responses and lowest limit of detection at room temperature compared with state-of-the-art NO2 sensors. Additionally, by employing LIG as a growth platform, flexibility and patterning strategies are achieved, which are the main challenges for MOF-based electronic devices. These results provide key insight into applying MOFtronics as high-performance healthcare devices.
RESUMEN
Recently, interest in transparent electrodes has been increasing in biomedical engineering applications for such as electro-optical hybrid neuro-technologies. However, conventional photolithography-based electrode fabrication methods have limited design customization and large-area applicability. For biomedical engineering applications, it is crucial that we can easily customize the electrode design for different patients over a large body area. In this paper, we propose a novel method to fabricate customization-friendly, transparent, ultrathin, gold microelectrodes using inkjet printing technology. Unlike with typical direct printing of conductive inks, we inkjet-printed a polymer nucleation-inducing seed layer, followed by mask-less vacuum deposition of ultrathin gold (<6 nm) to produce selectively, high-transparency electrodes in the predefined shapes of the inkjet-printed polymer. Owing to the design flexibility of inkjet printing, the transparent ultrathin gold electrodes can be highly efficient in design customization over a large area. Simultaneously, a layer of nonconductive gold islands is formed in the nonprinted region, and this nanostructured layer can implement a photothermal effect that offers versatility for novel biomedical applications. As a demonstration of the effectiveness of these transparent electrodes, and the facile implementation of the photothermal effect for biomedical applications, we successfully fabricated transparent resistive temperature detectors. We used these to directly sense the photothermal effect and to demonstrate their bioimaging capabilities.
RESUMEN
We propose inkjet-printed high-speed and transparent temperature sensors based on the thermoelectric effect for direct monitoring of the photothermal effect. They consist of highly transparent organic thermoelectric materials that allow excellent biocompatibility and sub-ms temporal resolution, simultaneously. Our transparent thermoelectric temperature sensors can be used to advance various photothermal biomedical applications.
Asunto(s)
Calor , TemperaturaRESUMEN
With the advent of 5G wireless and Internet of Things technologies, flexible and stretchable printed circuit boards (PCBs) should be designed to address all the specifications necessary to receive signal transmissions, maintaining the signal integrity, and providing electrical connections. Here, we propose a silver nanoparticle (AgNP)/silver nanowire (AgNW) hybrid conductor and high-quality microprinting technology for fabricating flexible and stretchable PCBs in high-performance 5G wireless communication. A simple and low-cost reverse offset printing technique using a commercial adhesive hand-roller was adapted to ensure high-resolution and excellent pattern quality. The AgNP/AgNW micropatterns were fabricated in various line widths, from 5 µm to 5 mm. They exhibited excellent pattern qualities, such as fine line spacing, clear edge definition and outstanding pattern uniformity. After annealing via intense pulsed light irradiation, they showed outstanding electrical resistivity (15.7 µΩ cm). Moreover, they could withstand stretching up to a strain of 90% with a small change in resistance. As a demonstration of their practical application, the AgNP/AgNW micropatterns were used to fabricate 5G communication antennas that exhibited excellent wireless signal processing at operating frequencies in the C-band (4-8 GHz). Finally, a wearable sensor fabricated with these AgNP/AgNW micropatterns could successfully detected fine finger movements in real time with excellent sensitivity.
RESUMEN
Micro size antennas have significant merits due to the small size effect, enabling new device concepts. However, the low-quality factor (Q-factor), the large size of impedance matching components, and the poor selectivity of the multi-array design remain challenging issues. To solve these issues, a floating coil structure stacked on a loop micro-antenna is suggested. Various floating coil designs are prepared with appropriate matching conditions at specific target frequencies, using an easy fabrication process without the need for additional space. A simple one-loop antenna design shows a higher Q-factor than other, more complicated designs. The micro-sized loop antenna with the 80 µm trace width design exhibits the highest Q-factor, around 31 within 7 GHz. The 8 different floating coil designs result in high-frequency selectivity from 1 to 7 GHz. The highest selectivity contrast and WPT efficiency are above 7 and around 1%, respectively. Considering the size of the antenna, the efficiency is not low, mainly due to the good matching effect with the high Q-factor of the floating coil and the loop antenna. This micro-antenna array concept with high integration density can be applied for advanced wireless neural stimulation or in wireless pixel array concepts in flexible displays.
RESUMEN
As a promising future treatment for stroke rehabilitation, researchers have developed direct brain stimulation to manipulate the neural excitability. However, there has been less interest in energy consumption and unexpected side effect caused by electrical stimulation to bring functional recovery for stroke rehabilitation. In this study, we propose an engineering approach with subthreshold electrical stimulation (STES) to bring functional recovery. Here, we show a low level of electrical stimulation boosted causal excitation in connected neurons and strengthened the synaptic weight in a simulation study. We found that STES with motor training enhanced functional recovery after stroke in vivo. STES was shown to induce neural reconstruction, indicated by higher neurite expression in the stimulated regions and correlated changes in behavioral performance and neural spike firing pattern during the rehabilitation process. This will reduce the energy consumption of implantable devices and the side effects caused by stimulating unwanted brain regions.
Asunto(s)
Estimulación Eléctrica/métodos , Rehabilitación de Accidente Cerebrovascular/métodos , Accidente Cerebrovascular/terapia , Algoritmos , Encéfalo/metabolismo , Encéfalo/fisiopatología , Manejo de la Enfermedad , Humanos , Modelos Biológicos , Actividad Motora , Neuronas/metabolismo , Recuperación de la Función , Accidente Cerebrovascular/fisiopatología , Sinapsis/metabolismo , Potenciales SinápticosRESUMEN
As a surrogate for human tactile cognition, an artificial tactile perception and cognition system are proposed to produce smooth/soft and rough tactile sensations by its user's tactile feeling; and named this system as "tactile avatar". A piezoelectric tactile sensor is developed to record dynamically various physical information such as pressure, temperature, hardness, sliding velocity, and surface topography. For artificial tactile cognition, the tactile feeling of humans to various tactile materials ranging from smooth/soft to rough are assessed and found variation among participants. Because tactile responses vary among humans, a deep learning structure is designed to allow personalization through training based on individualized histograms of human tactile cognition and recording physical tactile information. The decision error in each avatar system is less than 2% when 42 materials are used to measure the tactile data with 100 trials for each material under 1.2N of contact force with 4cm s-1 of sliding velocity. As a tactile avatar, the machine categorizes newly experienced materials based on the tactile knowledge obtained from training data. The tactile sensation showed a high correlation with the specific user's tendency. This approach can be applied to electronic devices with tactile emotional exchange capabilities, as well as advanced digital experiences.
Asunto(s)
Biomimética/métodos , Cognición , Aprendizaje Profundo , Tacto , Interfaz Usuario-Computador , Adulto , Femenino , Humanos , Masculino , Adulto JovenRESUMEN
The development of highly conductive electrodes with robust mechanical durability and clear transmittance in the visible to IR spectral range is of great importance for future wearable/flexible electronic applications. In particular, low resistivity, robust flexibility, and wide spectral transparency have a significant impact on optoelectronic performance. Herein, we introduce a new class of covellite copper monosulfide (CuS) nanosheet films as a promising candidate for soft transparent conductive electrodes (TCEs). An atmospheric sulfur adsorption-corrosion phenomenon represents a key approach in our work for the achievement of wafer-scale CuS nanosheet films through systematic control of the neat Cu layer thickness ranging from 2 to 10 nm multilayers at room temperature. These nanosheet films provide outstanding conductivity (â¼25 Ω sq-1) and high transparency (> 80%) in the visible to infrared region as well as distinct flexibility and long stability under air exposure, yielding a high figure-of-merit (â¼60) that is comparable to that of conventional rigid metal oxide material-based TCEs. Our unique room temperature synthesis process delivers high quality CuS nanosheets on any arbitrary substrates in a short time (< 1 min) scale, thus guaranteeing the widespread use of highly producible and scalable device fabrication.
RESUMEN
The effects of micro-hole arrays in the thin metal films were studied as a method to release bending stress in flexible electrodes and flexible thin film transistors (TFTs). Interest in flexible electronics is increasing, and many approaches have been suggested to solve the issue of the electrical failure of electrodes or electrical components such as TFTs after repeated bending. Here, we demonstrate a micro-hole array structure as a common solution to release bending stress. Although micro-size cracks were generated and propagated from the hole edges, the cracks stopped within a certain range when enough stress was released. Moreover, since the crack sites were predictable and controllable, a fatal electrical breakdown in a conductive layer such as a metal electrode or the semiconducting junction of a TFT can be prevented by specifically arranging the hole arrays. Thin film layers fabricated without holes suffered an electrical breakdown due to random crack propagation during bending tests. Aluminum thin film electrodes prepared with arrays of 3 µm diameter holes and 25% hole area showed excellent durability after 300,000 bending cycles. The change in resistance was below 3%. The electrical characteristics of an a-IGZO TFT with the micro-hole structure were almost equivalent to a standard a-IGZO TFT. After 10,000 bending cycles, ION and the ratio of ION/IOFF remained >107 A and â¼107, respectively. Since the effective hole diameter is micrometer in size, fabrication does not require additional process steps or expensive process equipment. Therefore, the approach can be an important way to enhance the reliability of various electrical devices in flexible and wearable applications.
RESUMEN
This research focuses on the development of a flexible tactile sensor array consisting of aluminum nitride (AlN) based on micro-electro-mechanical system (MEMS) technology. A total of 2304 tactile sensors were integrated into a small area of 2.5 × 2.5 cm2. Five hundred nm thick AlN film with strong c-axis texture was sputtered on Cr/Au/Cr (50/50/5 nm) layers as the sacrificial layer coated on a Si wafer. To achieve device flexibility, polydimethylsiloxane (PDMS) polymer and SU-8 photoresist layer were used as the supporting layers after etching away a release layer. Twenty-five mM (3-mercaptopropyl) trimethoxysilane (MPTMS) improves the adhesion between metal and polymers due to formation of a self-assembled monolayer (SAM) on the surface of the top electrode. The flexible tactile sensor has 8 × 8 channels and each channel has 36 sensor elements with nine SU-8 bump blocks. The tactile sensor array was demonstrated to be flexible by bending 90 degrees. The tactile sensor array was demonstrated to show clear spatial resolution through detecting the distinct electrical response of each channel under local mechanical stimulus.
RESUMEN
An artificial tactile system has attracted tremendous interest and intensive study, since it can be applied as a new functional interface between humans and electronic devices. Unfortunately, most previous works focused on improving the sensitivity of sensors. However, humans also respond to psychological feelings for sensations such as pain, softness, or roughness, which are important factors for interacting with others and objects. Here, we present an electronic skin concept that generates a "pain" warning signal, specifically, to sharp "prick" and "hot" sensations. To simplify the sensor structure for these two feelings, a single-body tactile sensor design is proposed. By exploiting "hot" feeling based on the Seebeck effect instead of the pyroelectric property, it is possible to distinguish points registering a "hot" feeling from those generating a "prick" feeling, which is based on the piezoelectric effect. The control of free carrier concentration in nanowire induced the appropriate level of Seebeck current, which enabled the sensor system to be more reliable. The first derivatives of the piezo and Seebeck output signals are the key factors for the signal processing of the "pain" feeling. The main idea can be applied to mimic other psychological tactile feelings.
RESUMEN
For appropriate treatment, accurate discrimination between seborrheic dermatitis and psoriasis in a timely manner is crucial to avoid complications. However, when they occur on the scalp, differential diagnosis can be challenging using conventional dermascopes. Thus, we employed smartphone-based multispectral imaging and analysis to discriminate between them with high accuracy. A smartphone-based multispectral imaging system, suited for scalp disease diagnosis, was redesigned. We compared the outcomes obtained using machine learning-based and conventional spectral classification methods to achieve better discrimination. The results demonstrated that smartphone-based multispectral imaging and analysis has great potential for discriminating between these diseases.
RESUMEN
A color-sensitive and spectrometer-free sensing method using plasmonic nanohole arrays and the color components, L*â¯, a*â¯, and b*â¯, of the CIELAB defined by the international commission on illumination (CIE) is introduced for the analysis of optically transparent materials in the visible range. Spectral analysis based on plasmonic nanoparticles or nanostructures can be applied to real-time bio-detection, but complex optical instrumentations and low spatial resolution have limited the sensing ability. Therefore, we take an advantage of color image processing instead of spectral analysis which induces the distinctive color information of plasmonic nanohole arrays with different transparent materials. It guarantees high spatial resolution which is essential to bio-detection such as living cells. To establish our sensing platform, the color components, L*â¯, a*â¯, and b*â¯, were extracted from photo images by an image sensor, statistically processed using a JAVA program, and finally utilized as three individual sensing factors. Additionally, our study on a correlation between the spacing of plasmonic sensors and the color sensitivity to the refractive index reveals geometrically optimal conditions of nanohole arrays. The weighted mean calculation with the three individual sensing factors offers an enhanced distinction of the optical difference for transparent materials. In this work, a color sensitivity of 156.94 RIU-1 and a minimum mean absolute error of 1.298×10-4 RIU were achieved. The difference in the refractive index can be recognized up to 10-4 level with the suggested sensing platform and the signal process. This unique color-sensitive sensing method enables a simple, easy-to-control, and highly accurate analysis without complicated measurement systems including a spectrometer. Therefore, our sensing platform can be applied as a very powerful tool to in-situ label-free bio-detection fields.
Asunto(s)
Técnicas Biosensibles , Nanoestructuras/química , Nanotecnología/métodos , Excipientes , Resonancia por Plasmón de SuperficieRESUMEN
Phototransistors that are based on a hybrid vertical heterojunction structure of two-dimensional (2D)/quantum dots (QDs) have recently attracted attention as a promising device architecture for enhancing the quantum efficiency of photodetectors. However, to optimize the device structure to allow for more efficient charge separation and transfer to the electrodes, a better understanding of the photophysical mechanisms that take place in these architectures is required. Here, we employ a novel concept involving the modulation of the built-in potential within the QD layers for creating a new hybrid MoS2/PbS QDs phototransistor with consecutive type II junctions. The effects of the built-in potential across the depletion region near the type II junction interface in the QD layers are found to improve the photoresponse as well as decrease the response times to 950 µs, which is the faster response time (by orders of magnitude) than that recorded for previously reported 2D/QD phototransistors. Also, by implementing an electric-field modulation of the MoS2 channel, our experimental results reveal that the detectivity can be as large as 1 × 1011 jones. This work demonstrates an important pathway toward designing hybrid phototransistors and mixed-dimensional van der Waals heterostructures.
RESUMEN
Wetting has been studied in various fields: chemical industry, automobile manufacturing, food companies, and even life sciences. In these studies, super-hydrophobic surfaces have been achieved through complex steps and processes. To realize super-hydrophobicity, however, we demonstrated a simple and single pass laser process for the fabrication of micro/nano hierarchical structures on the flexible polytetrafluoroethylene (PTFE, Teflon) surface. The fabricated hierarchical structures helped increase the hydrophobicity by augmenting the surface roughness and promoting air-trapping. In addition, we employed a low-cost and high-throughput replication process producing numerous polydimethylsiloxane (PDMS) replicas from the laser-processed PTFE film. Thanks to the anti-adhesive characteristics of PTFE and the elasticity of PDMS, the structure perfectly transferred to the replica without any mechanical failure. Moreover, our designed mesh patterns offered the possibility of large area applications through varying the process parameters (pitch, beam spot size, laser fluence, and scan speed). Even though mesh patterns had relatively large pitch (190 µm), we were able to achieve high contact angle (>150°). Through pneumatically deformed structure, we clearly showed that the shape of the droplets on our laser-processed super-hydrophobic surface was spherical. Based on these outcomes, we can expect our single laser pulse exposure process can overcome many drawbacks and offer opportunities for advancing applications of the wetting phenomena.