17-4 PH Steel Parts Obtained through MEX and PBF-LB/M Technologies: Comparison of the Structural Properties.

The material extrusion (MEX) method utilizing highly filled metal filament presents an alternative to advanced additive metal manufacturing technologies. This process enables the production of metal objects through deposition and sintering, which is particularly attractive compared to powder bed fusion (PBF) technologies employing lasers or high-power electron beams. PBF requires costly maintenance, skilled operators, and controlled process conditions, whereas MEX does not impose such requirements. This study compares research on 17-4 PH steel manufactured using two different commercially available techniques: MEX and powder bed fusion with laser beam melting (PBF-LB/M). This research included assessing the density of printed samples, analyzing surface roughness in two printing planes, examining microstructure including porosity and density determination, and measuring hardness. The conducted research aimed to determine the durability and quality of the obtained samples and to evaluate their strength. The research results indicated that samples produced using the PBF-LB/M technology exhibited better density and a more homogeneous structure. However, MEX samples exhibited better strength properties (hardness).

Bending Strength of Continuous Fiber-Reinforced (CFR) Polyamide-Based Composite Additively Manufactured through Material Extrusion.

This paper shows the three-point bending strength analysis of a composite material consisting of polyamide doped with chopped carbon fiber and reinforced with continuous carbon fiber produced by means of the material extrusion (MEX) additive manufacturing technique. For a comparison, two types of specimens were produced: unreinforced and continuous fiber-reinforced (CFR) with the use of carbon fiber. The specimens were fabricated in two orientations that assure the highest strength properties. Strength analysis was supplemented by additional digital image correlation (DIC) analysis that allowed for the identification of regions with maximum strain within the specimens. The utilization of an optical microscope enabled a fractographic examination of the fracture surfaces of the specimens. The results of this study demonstrated a beneficial effect of continuous carbon fiber reinforcement on both the stiffness and strength of the material, with an increase in flexural strength from 77.34 MPa for the unreinforced composite to 147.03 MPa for the composite reinforced with continuous carbon fiber.

Microstructural Investigation of Process Parameters Dedicated to Laser Powder Bed Fusion of AlSi7Mg0.6 Alloy.

This study presents a microstructural investigation of the printing parameters of an AlSi7Mg0.6 alloy produced by powder bed fusion (PBF) using laser beam melting (LB/M) technology. The investigation focused on the effects of laser power, exposure velocity, and hatching distance on the microhardness, porosity, and microstructure of the produced alloy. The microstructure was characterized in the plane of printing on a confocal microscope. The results showed that the printing parameters significantly affected the microstructure, whereas the energy density had a major effect. Decreasing the laser power and decreasing the hatching distance resulted in increased porosity and the increased participation of non-melted particles. A mathematical model was created to determine the porosity of a 3D-printed material based on three printing parameters. Microhardness was not affected by the printing parameters. The statistical model created based on the porosity investigation allowed for the illustration of the technological window and showed certain ranges of parameter values at which the porosity of the produced samples was at a possible low level.

An Eco-Friendly and Innovative Approach in Building Engineering: The Production of Cement-Glass Composite Bricks with Recycled Polymeric Reinforcements.

Cementitious-glass composite bricks (CGCBs) with 3D-printed reinforcement structures made of PET-G could be an innovative production method that relies on recycling glass waste (78%) and PET-G (8%). These bricks offer a promising solution for the construction industry, which has a significant impact on climate change due to its greenhouse gas emissions and extensive use of natural aggregates. The approach presented in this article serves as an alternative to using conventional building materials that are not only costlier but also less environmentally friendly. The conducted research included mechanical tests using digital image correlation (DIC), utilized for measuring deformations in specimens subjected to three-point bending and compression tests, as well as thermal investigations covering measurements of their thermal conductivity, thermal diffusivity, and specific heat. The results highlighted the superior thermal properties of the CGCBs with PET-G reinforcements compared to traditional cementitious-glass mortar (CGM). The CGCBs exhibited a 12% lower thermal conductivity and a 17% lower specific heat. Additionally, the use of specially designed reinforcement substantially enhanced the mechanical properties of the bricks. There was a remarkable 72% increase in flexural strength in the vertical direction and a 32% increase in the horizontal direction.

Comparison of Additively Manufactured Polymer-Ceramic Parts Obtained via Different Technologies.

This paper aims to compare two ceramic materials available for additive manufacturing (AM) processes-vat photopolymerization (VPP) and material extrusion (MEX)-that result in fully ceramic parts after proper heat treatment. The analysis points out the most significant differences between the structural and mechanical properties and the potential application of each AM technology. The research revealed different behaviors for the specimens obtained via the two mentioned technologies. In the case of MEX, the specimens exhibited similar microstructures before and after heat treatment. The sintering process did not affect the shape of the grains, only their size. For the VPP specimens, directly after the manufacturing process, irregular grain shapes were registered, but after the sintering process, the grains fused, forming a solid structure that made it impossible to outline individual grains and measure their size. The highest compression strength was 168 MPa for the MEX specimens and 81 MPa for the VPP specimens. While the VPP specimens had half the compression strength, the results for the VPP specimens were significantly more repeatable.

A Comparative Investigation of Properties of Metallic Parts Additively Manufactured through MEX and PBF-LB/M Technologies.

In this study, the research on 316L steel manufactured additively using two commercially available techniques, Material Extrusion (MEX) and Laser Powder Bed Fusion of Metals (PBF-LB/M), were compared. The additive manufacturing (AM) process based on powder bed synthesis is of great interest in the production of metal parts. One of the most interesting alternatives to PBF-LB/M, are techniques based on material extrusion due to the significant initial cost reduction. Therefore, the paper compares these two different methods of AM technologies for metals. The investigations involved determining the density of the printed samples, assessing their surface roughness in two printing planes, examining their microstructures including determining their porosity and density, and measuring their hardness. The tests carried out make it possible to determine the durability, and quality of the obtained sample parts, as well as to assess their strength. The conducted research revealed that samples fabricated using the PBF-LB/M technology exhibited approximately 3% lower porosity compared to those produced using the MEX technology. Additionally, it was observed that the hardness of PBF-LB/M samples was more than twice as high as that of the samples manufactured using the MEX technology.

Regeneration of the Damaged Parts with the Use of Metal Additive Manufacturing-Case Study.

The paper shows the results related to regeneration possibilities analysis of a damaged slider removed from a hydraulic splitter that was repaired using additive manufacturing (AM), laser-based powder bed fusion of metals (PBF-LB/M) technology. The results demonstrate the high quality of the connection zone between the original part and the regenerated zone. The hardness measurement conducted at the interface between the two materials indicated a significant increase equal to 35% by using the M300 maraging steel, as a material for regeneration. Additionally, the use of digital image correlation (DIC) technology enabled the identification of the area where the largest deformation occurred during the tensile test, which was out of the connection zone between the two materials.

Bending Strength of Polyamide-Based Composites Obtained during the Fused Filament Fabrication (FFF) Process.

The research shows the comparison between two types of polyamide-based (PA) composites and pure, base material. The conducted analysis describes how the additions of carbon fibers and glass microbeads affect the material's properties and its behavior during the bending tests. All samples have been tested in the three main directions available during the FFF process. To extend the scope of the research, additional digital-image-correlation tests and fracture analyses were made. The obtained results indicated a positive influence of the addition of carbon fibers into the material's volume (from 81.39 MPa in the case of pure PA to 243.62 MPa in the case of the PA reinforced by carbon fibers).