The effect of stem modularity and mode of fixation on tibial component stability in revision total knee arthroplasty.

The effect of stem length, diameter, and mode of fixation on the motion and stress transfer of a cemented tibial tray were evaluated for in 12 cadaver knees. There was a significant decrease in motion of the tibial tray with increasing press-fit stem length (75-150 mm) and increasing stem diameter (10-14 mm). Cemented tibial stems showed significantly less tray motion than uncemented stems. The short cemented stems produced tray stability equivalent to long press-fit stems. Although there was a trend for increased proximal tibial stress shielding with the use of cement and longer, wider stems, the trend was not statistically significant. Modular, press-fit stems can achieve tray stability similar to a smaller cemented stem and can avoid the potential problems with cement.

Arthroscopic treatment of an intra-articular lipoma of the knee joint.

Intra-articular lipoma is an exceedingly rare diagnosis. There have been less than 15 documented cases of an intra-articular lipoma of the knee joint. This report presents the first description of an intra-articular knee lipoma treated entirely by arthroscopic methods. Preoperative history, examination, and imaging studies are reviewed. Intraoperative findings, treatment, and postoperative evaluation are discussed as well. Symptomatic intra-articular lipoma of the knee joint can be successfully treated by arthroscopic resection. Differentiating intra-articular lipoma from lipoma arborescens, a similar but more common condition, is important with regards to optimal treatment.

Distal biceps tendon ruptures: a historical perspective and current concepts.

Distal biceps tendon rupture is a relatively rare injury most commonly seen in the dominant extremity of men between 40 and 60 years of age. It occurs when an eccentric extension force is applied to a contracting biceps muscle. The hallmark finding is a palpable defect in the distal biceps, which is accentuated by elbow flexion. Radiographic evaluation is usually not necessary. Acute surgical repair is advocated for optimal return of function by either a one-incision or a modified two-incision muscle-splitting technique. The arm is protected for 6 to 8 eight weeks after surgery. Unrestricted range of motion and gentle strengthening may begin after the 6 - 8 week protection period. Return to unrestricted activity is usually allowed by 5 months after surgery.

Synovial chondromatosis of the elbow.

Synovial chondromatosis is an uncommon disorder with rare occurrence in the elbow. Case reports in the literature for elbow synovial chondromatosis have described presenting symptoms secondary to peripheral nerve compressions or localized bursitis. We discuss a case of synovial chondromatosis of the elbow that presented as an isolated soft-tissue mass over the radial head-more suggestive of a soft-tissue tumor than of synovial chondromatosis.

Arthroscopic stabilization of anterior shoulder instability: a historical perspective.

The role of arthroscopic procedures in the management of glenohumeral instability continues to evolve and represents an effective alternative for addressing the pathology associated with this condition. Patient selection criteria, operative techniques, and implants all continue to evolve and have resulted in improved rates of success. Arthroscopic procedures benefit patients by avoiding the common morbidities associated with the disruption of the anterior soft tissues, including a loss of external rotation associated with open procedures. Arthroscopic procedures remain technically demanding and require skills to address all of the existing pathology. The surgeon must be prepared to address many conditions beyond the Bankart lesions including glenoid bone lesions. capsular laxity, rotator interval lesions, and SLAP lesions. In addition to the documentation of recurrence, the success of this procedure must be evaluated within the context of retained ranges of motion, recovery time, proprioceptive control, and the return to prior levels of activity. Further studies are necessary to continue to validate the efficacy of arthroscopic stabilization.

Orthopaedic manifestations of systemic lupus erythematosus.

Systemic lupus erythematosus (SLE) is a chronic inflammatory autoimmune disease of unknown origin. It affects multiple organ systems, but most frequently the musculoskeletal system. Highly variable manifestations include small and large joint involvement, spinal involvement, periarticular tissue symptoms, and complications associated with chronic steroid use such as osteonecrosis, osteoporosis, and stress fractures. The following review summarizes the common orthopaedic manifestations of SLE.

Radiographic comparison of grit-blasted hydroxyaptite and arc-deposited hydroxyapatite acetabular components. A four-year follow-up study.

High rates of aseptic loosening have been reported for microstructured hydroxyapatite-coated acetabular components. A macrostructured component surface (arc-deposition) not only improves resistance to shear forces experienced by the acetabular component and increases initial stability, but also provides channels for bone ingrowth. The purpose of this investigation was to radiographically compare a series of grit-blasted (microstructured) and arc-deposited (macrostructured) hydroxyapatite-coated acetabular components. A minimum 4-year retrospective radiographic analysis of acetabular components was performed on a total of 50 total hip arthroplasties. At 4 years, arc-deposited components were associated with fewer radiolucent lines in all Charnley zones, particularly Charnley zone III. While the 4-year results for arc-deposited hydroxyapatite acetabular components are superior to their microstructured predecessors, long-term results are still unknown.

Spontaneous rib fracture during pregnancy. A case report and review of the literature.

No studies have demonstrated a direct relationship between pregnancy and rib fracture. A case of spontaneous rib fracture in the third trimester presents the opportunity to examine factors unique to pregnancy that may predispose the patient to stress fractures of the lower ribs. A 28-year old woman in week 31 of her pregnancy presented with the chief complaint of acute onset of right upper quadrant pain. A chest radiograph demonstrated a minimally displaced fracture of the right 10th rib. During pregnancy, the enlarging uterus causes certain opposing muscular forces to act on the ribs, making them more susceptible to fracture after minimal trauma or after repeated stresses such as a chronic cough.

The accuracy of computed tomography for determining femoral and tibial total knee arthroplasty component rotation.

Patellofemoral complications, instability, and tibial polyethylene wear after total knee arthroplasty (TKA) resulting from malrotation of the tibial or femoral components (or both) may be difficult to diagnose based on physical examination and standard knee radiographs. The preoperative assessment of implant rotational alignment is critical in planning treatment because the femoral or tibial component (or both) may need to be revised if malpositioned. The purpose of this study was to ascertain the accuracy of computed tomography (CT) scan for determining rotational alignment of femoral and tibial components in TKA. TKA components were inserted in human cadaver specimens at neutral and 5 degrees of external or internal rotation. For each position, the amount of rotation, determined from digital photographs, was compared with CT scan. The correlation coefficient between these two values averaged 0.87, which was significant at P < .05. The CT scan protocol described in this study can be applied clinically to patients with patellofemoral complaints to confirm or rule out the presence of component malrotation.

A biomechanical comparison of Schuhli nuts or cement augmented screws for plating of humeral fractures.

Schuhli locking nuts can be used in poor quality cortical bone to enhance fixation stability as an alternative to cement augmented screws. This study compared the fixation strength and stability of plate constructs using Schuhli locking nuts with standard screws and cement augmented screws for fixation of simulated humeral shaft fractures in a test model with osteoporosis. The constructs were tested in axial compression, 4-point bending, and torsion to determine fixation stability. The humeri were cycled in torsion (4.5 Nm) for 1000 cycles to simulate upper extremity use during the early postoperative period and retested for stability. The Schuhli locking nuts and cement augmented screws had significantly greater fixation stability than the standard screws before (range, 6-14 times greater) and after cycling in torsional loading (range, 3-3.6 times greater). Although cement augmented screws and Schuhli augmentation showed increased fixation stability compared with the standard screws in axial and 4-point bending before cycling (range, 1.3-1.4 times greater), this was not significant. Compared with Schuhli fixation, cement augmented screws showed no significant difference in fixation stability in all loading modes before and after cycling. Schuhli locking nuts offer the stability of cement augmentation while avoiding its potential adverse effects on fracture healing with extravasation and thermal necrosis.

Anticoagulant treatment of thromboembolism with intravenous heparin therapy in the early postoperative period following total joint arthroplasty.

BACKGROUND: Treatment of thromboembolism with intravenous heparin therapy in the early postoperative period after total joint arthroplasty has been associated with a high rate of complications. The purpose of the present study was to compare the rate of bleeding complications in a group of patients who required intravenous heparin therapy for the treatment of thromboembolism after total hip or knee arthroplasty with the rate in a control group of patients who received only prophylactic anticoagulation. METHODS: The postoperative courses of forty-four consecutive patients who were managed with intravenous administration of heparin and oral administration of warfarin for the treatment of a thromboembolic event following unilateral total hip or knee arthroplasty were compared with those of a control group of 376 consecutive patients who had these same procedures but did not have a thromboembolic complication. The patients in the control group were managed with prophylactic anticoagulation with use of enoxaparin. Sixty-eight percent (thirty) of the forty-four patients in the heparin group received the initial dose of heparin on or before the fourth postoperative day, and 82 percent (thirty-six) received an initial bolus of 5000 units of heparin at the initiation of therapy. RESULTS: The rate of bleeding complications was 9 percent (four of forty-four) in the heparin group, compared with 6 percent (twenty-three of 376) in the control group (p = 0.44). The mean transfusion requirement in the heparin group (1.8 units of packed red blood cells) was significantly greater than that in the control group (0.8 unit) (p < 0.0001). Three of the four patients who had a bleeding complication while receiving heparin and warfarin had coagulation parameters that were substantially higher than recommended levels. The mean duration of hospitalization in the heparin group (fifteen days) was significantly longer than that in the control group (seven days) (p < 0.0001). CONCLUSIONS: The results of the present study suggest that the use of intravenous heparin therapy for the treatment of thromboembolism in the early postoperative period after total joint arthroplasty is associated with a rate of bleeding complications that is similar to that associated with the use of prophylactic anticoagulation with use of enoxaparin alone. One should expect an increased transfusion requirement and a longer duration of hospitalization for patients who require intravenous heparin therapy for the treatment of a thromboembolic event.

New technique for treatment of unstable distal femur fractures by locked double-plating: case report and biomechanical evaluation.

BACKGROUND: A comminuted, intra-articular distal femur fracture was surgically treated by the authors with a locked, double-plating technique because fixation stability could not be initially achieved by using a standard double-plating technique. The purpose of this study was to determine biomechanically whether a locked double-plate construct would enhance fixation stability compared with a nonlocked double-plate construct. METHODS: Six matched pairs of mildly osteopenic femurs were selected and all had a reproducible intra-articular fracture pattern created. Each pair underwent fixation with either a double-plating construct or a locked, double-plating construct that was randomly assigned. The instrumented femurs were then mechanically tested in several loading modes to determine fixation stability. After initial testing, specimens were cyclically loaded and retested for stability. RESULTS: The locked, double-plating construct provided significantly greater fixation stability than the standard double-plating construct in precycling and postcycling biomechanical testing. CONCLUSION: The technique described is particularly applicable for severely comminuted fractures of the distal femur and fractures in osteopenic bone with poor screw purchase. It offers a simple alternative for enhancing fixation stability, which avoids the potential complications of methylmethacrylate-enhanced screw fixation.

Long-term follow-up of the one-bone forearm procedure.

The one-bone forearm procedure can be a successful salvage option for forearm stability in selected patients and is indicated if instability and bone loss are irreparable by other means. We report a case of a dysfunctional arm secondary to radical débridement of the ulna after osteomyelitis treated successfully with a one-bone forearm procedure and followed up for 8 years.

Vertical shear fractures of the femoral neck. A biomechanical study.

A biomechanical cadaver study was performed to compare the strength and stability of three cannulated cancellous lag screws with a sliding hip screw for fixation of a vertically oriented fracture of the femoral neck (Pauwels Type III). Using eight matched pairs of human cadaveric femurs, vertically oriented femoral neck osteotomies were created, reduced, and randomized to one of the two fixation methods. The constructs were tested with incremental axial loading from 100 N to 1200 N and cyclical loading at 1000 N for 10,000 cycles; fracture displacements and ultimate load to failure were determined. The specimens stabilized using a sliding hip screw showed less inferior femoral head displacement, less shearing displacement at the osteotomy site, and a much greater load to failure than did those stabilized with multiple cancellous lag screws. These results support the use of a sliding hip screw for treatment of vertically oriented fractures of the femoral neck.

Wear rates of ceramic-on-ceramic bearing surfaces in total hip implants: a 12-year follow-up study.

A retrospective clinical and radiographic analysis was performed on 58 patients (60 hips; mean age at time of surgery, 45.2 years) at a minimum of 10-year follow-up (mean, 12.7 years) after total hip replacement using a ceramic-on-ceramic hearing total hip implant (Autophor, Smith and Nephew, Memphis, TN). Mean wear rate at final follow-up was 0.21 mim, averaging 0.016 mm/y. There were no cases of periprosthetic osteolysis in the acetabuulum or femur. For the unrevised components, there were 3 (5%) cases of protrusio acetabuli and 4 (7%) cases of acetabular component loosening. On the femoral side, 78.3% had distal pedestal formation, and 83% had greater than 2 mm implant-bone radiolucencies in more than 5 Gruen zones as a result of gross motion of the stem. Despite radiographic evidence of implant loosening, this hard bearing articulation functioned well in vivo for more than 12 years with remarkably low wear--approximately one tenth the rate reported for metal-on-polyethylene total hip bearings.

The use of an injectable, biodegradable calcium phosphate bone substitute for the prophylactic augmentation of osteoporotic vertebrae and the management of vertebral compression fractures.

STUDY DESIGN: A biomechanical study comparing two materials for augmentation of osteoporotic vertebral bodies and vertebral bodies after compression fracture. OBJECTIVES: To compare an injected, biodegradable calcium phosphate bone substitute with injected polymethylmethacrylate bone cement for strengthening osteoporotic vertebral bodies and improving the integrity of vertebral compression fractures. SUMMARY OF BACKGROUND DATA: Injection of polymethylmethacrylate bone cement into fractured vertebral bodies has been used clinically. However, there is concern about thermal damage to the neural elements during polymerization of the polymethylmethacrylate bone cement as well as its negative effects on bone remodeling. Biodegradable calcium phosphate bone substitutes have been studied for enhancement of fixation in fractured vertebrae. METHODS: Forty fresh osteoporotic thoracolumbar vertebrae were used for two separate parts of this study: 1) injection into osteoporotic vertebrae: intact control (n = 8), calcium phosphate (n = 8), and polymethylmethacrylate bone cement (n = 8) groups. Each specimen then was loaded in anterior compression until failure; 2) injection into postfractured vertebrae: calcium phosphate (n = 8) and polymethylmethacrylate bone cement (n = 8) groups. Before and after injection, the specimens were radiographed in the lateral projection to determine changes in vertebral body height and then loaded to failure in anterior bending. RESULTS: For intact osteoporotic vertebrae, the average fracture strength was 527 +/- 43 N (stiffness, 84 +/- 11 N/mm), 1063 +/- 127 N (stiffness, 157 +/- 21 N/mm) for the group injected with calcium phosphate, and 1036 +/- 100 N (stiffness, 156 +/- 8 N/mm) for the group injected with polymethylmethacrylate bone cement. The fracture strength and stiffness in the calcium phosphate bone substitute group and those in the polymethylmethacrylate bone cement group were similar and significantly stronger than those in intact control group (P < 0.05). For the compression fracture study, anterior vertebral height was increased 58.5 +/- 4.6% in the group injected with calcium phosphate and 58.0 +/- 6.5% in the group injected with polymethylmethacrylate bone cement as compared with preinjection fracture heights. No significant difference between the two groups was found in anterior vertebral height, fracture strength, or stiffness. CONCLUSION: This study demonstrated that the injection of a biodegradable calcium phosphate bone substitute to strengthen osteoporotic vertebral bodies or improve vertebral compression fractures might provide an alternative to the use of polymethylmethacrylate bone cement.