RESUMEN
This study describes the development of a landslide monitoring system for the purpose of reducing damages caused by landslides in natural terrain. The system was developed to analyze the effects of landslide-inducing rainfall and the behavior of slopes through 12 monitoring stations that are distributed across eight national parks in Korea. Several sensors and a data acquisition equipment to monitor landslide were installed in each station. The composition of the system and its operating program were designed to efficiently manage the sizeable amounts of real-time monitoring data that are collected from the various stations. To test the potential of the developed system for reliable landslide hazard evaluations, data measured over a five-year period by the two monitoring stations in Jirisan National Park were analyzed. Subsequently, the suction stress of the soil over the monitoring period was calculated by applying laboratory test result of the geotechnical and unsaturated soil properties in the analysis domain area. The infinite slope stability analysis combined with an effective stress concept based on the suction stress was applied to calculate the factor of safety. This method also enabled the temporal and quantitative evaluation of slope stability in natural terrain. In addition, based on the monitoring and slope stability analysis results, an analysis for the spatial classification of landslide hazards was conducted. The analysis results quantitatively and statistically demonstrated that 98% of historical landslide initiation areas were classified as high hazard levels.
RESUMEN
The shear and particle crushing characteristics of the failure plane (or shear surface) in catastrophic mass movements are examined with a ring shear apparatus, which is generally employed owing to its suitability for large deformations. Based on results of previous experiments on waste materials from abandoned mine deposits, we employed a simple numerical model based on ring shear testing using the particle flow code (PFC2D). We examined drainage, normal stress, and shear velocity dependent shear characteristics of landslide materials. For shear velocities of 0.1 and 100 mm/s and normal stress (NS) of 25 kPa, the numerical results are in good agreement with those obtained from experimental results. The difference between the experimental and numerical results of the residual shear stress was approximately 0.4 kPa for NS equal to 25 kPa and 0.9 kPa for NS equal to 100 kPa for both drained and undrained condition. In addition, we examined particle crushing effect during shearing using the frictional work concept in PFC. We calculated the work done by friction at both peak and residual shear stresses, and then used the results as crushing criteria in the numerical analysis. The frictional work at peak and the residual shear stresses was ranged from 303 kPa·s to 2579 kPa·s for given drainage and normal stress conditions. These results showed that clump particles were partially crushed at peak shear stress, and further particle crushing with respect to the production of finer in shearing was recorded at residual shear stress at the shearing plane.
RESUMEN
Casein is often used as an eco-friendly wood adhesive. In this study, we used casein for soil cementation by mixing it with Jumunjin sand, sodium hydroxide (SH), and calcium hydroxide (CH) as a standard casein formula. The modified casein binder with different proportions of SH and CH was applied to improve water resistance. Furthermore, a blast furnace slag (BFS) was additionally mixed and reacted with alkalinity of modified casein binder. Thus, three types (standard, modified, and modified + BFS, referred to as STD, MOD, and MBS, hereafter) of casein binders were tested for durability and strength of casein-cemented sand. A piezoelectric sensor was installed within each sample to determine the curing time of the casein-cemented samples. The samples were air-cured at room temperature for seven days and some were repeatedly immersed in water thrice. Unconfined compression and jar slake tests were carried out to evaluate the strength and durability of the casein-cemented sand. Also, the microstructure was analyzed using a scanning electron microscope (SEM). We observed variations of peak conductance and corresponding frequency converged as the curing time increased. It was most significant for the MBS samples, which developed strength early. The unconfined compressive strength (UCS) of the air-cured samples was higher than those repeatedly immersed in water due to wash-off of the casein binder. The UCS of the dry MBS sample was 9900 kPa while that of the immersed sample was 430 kPa, which gradually decreased to 60 kPa upon repeated immersion. The samples with STD and MOD had no resistance to durability and showed cracks on the surface, while the MBS sample exhibited significantly improved durability and no cracks. We found that the MBS binder had a positively significant effect on the durability and strength of casein-cemented sand.