RESUMEN
The device performance of deep-blue perovskite light-emitting diodes (PeLEDs) is primarily constrained by low external quantum efficiency (EQE) especially poor operational stability. Herein, we develop a facile strategy to improve deep-blue emission through rational interface engineering. We innovatively reported the novel electron transport material, 4,6-Tris(4-(diphenylphosphoryl)phenyl)-1,3,5-triazine (P-POT2T), and utilized a sequential wet-dry deposition method to form homogenic gradient interface between electron transport layer (ETL) and perovskite surface. Unlike previous reports that achieved carrier injection balance by inserting new interlayers, our strategy not only passivated uncoordinated Pb in the perovskite via P=O functional groups but also reduced interfacial carrier recombination without introducing new interfaces. Additionally, this strategy enhanced the interface contact between the perovskite and ETL, significantly boosting device stability. Consequently, the fabricated deep-blue PeLEDs delivered an external quantum efficiency (EQE) exceeding 5% (@ 460 nm) with an exceptional halftime extended to 31.3 minutes. This straightforward approach offers a new strategy to realize highly efficient especially stable PeLEDs.
RESUMEN
Enhancing the intrinsic stability of perovskite and through encapsulation to isolate water, oxygen, and UV-induced decomposition are currently common and most effective strategies in perovskite solar cells. Here, the atomic layer deposition process is employed to deposit a nanoscale (≈100 nm), uniform, and dense Al2O3 film on the front side of perovskite devices, effectively isolating them from the erosion caused by water and oxygen in the humid air. Simultaneously, nanoscale (≈100 nm) TiO2 films are also deposited on the glass surface to efficiently filter out the ultraviolet (UV) light in the light source, which induces degradation in perovskite. Ultimately, throughthe collaborative effects of both aspects, the stability of the devices is significantly improved under conditions of humid air and illumination. As a result, after storing the devices in ambient air for 1000 h, the efficiency only declines to 95%, and even after 662 h of UV exposure, the efficiency remains at 88%, far surpassing the performance of comparison devices. These results strongly indicate that the adopted Al2O3 and TiO2 thin films play a significant role in enhancing the stability of perovskite solar cells, demonstrating substantial potential for widespread industrial applications.
RESUMEN
The performance of blue perovskite light-emitting diodes (PeLEDs) lags behind the green and red counterparts owing to high trap density and undesirable red shift of the electroluminescence spectrum under operation conditions. Organic molecular additives were employed as passivators in previous reports. However, most commonly have limited functions, making it challenging to effectively address both efficiency and stability issues simultaneously. Herein, we reported an innovatively dynamic in situ hydrolysis strategy to modulate quasi-2D sky-blue perovskites by the multifunctional passivator phenyl dichlorophosphate that not only passivated the defects but also underwent in situ hydrolysis reaction to stabilize the emission. Moreover, hydrolysis products were beneficial for low-dimensional phase manipulation. Eventually, we obtained high-performance sky-blue PeLEDs with a maximum external quantum efficiency (EQE) of 16.32% and an exceptional luminance of 5740 cd m-2. More importantly, the emission peak of devices located at 485 nm remained stable under different biases. Our work signified the significant advancement toward realizing future applications of PeLEDs.
RESUMEN
Oxygen is difficult to be physically removed. Oxygen will be excited by light to form free radicals which further attack the lattice of perovskite. The stabilization of α-FAPbI3 against δ-FAPbI3 is the key to optimize perovskite solar cells. Herein, the simple molecule, benzaldehyde (BAH) is adopted. The photochemical shield will be established in perovskite layer. Moreover, heterogeneous nucleation induced by BAH enhances the crystallization of α-FAPbI3. Consequently, the stability of device is improved significantly. The target device maintains 95% of original power conversion efficiency after 1500 h under air conditions and light-emitting diode light. The power conversion efficiency increases from 23.21% of pristine device to 24.82% of target device.
RESUMEN
Organic-inorganic halide perovskites (OIHPs) obtained tremendous attention due to their low cost and excellent properties. However, the stability and toxicity of Pb-based OIHPs (POIHPs), as well as the weakness of efficiency and stability in Sn-based OIHPs (SOIHPs), are still serious issues for commercial application. Notably, composition engineering is an effective and direct strategy for improving these issues along with the control and modification of properties. Recently, the doping strategies for POIHPs and SOIHPs are booming. Based on the relationship between properties and composition, the doping strategies for POIHPs and SOIHPs, aiming to provide a comprehensive review and guidance for the research are systematically summarized. Moreover, the doping strategies for Pb-Sn mixed OIHPs are also discussed. Finally, a brief perspective and conclusion toward future possible doping schemes and properties designment of POIHPs and SOIHPs are offered.