Axial and Rotational Malreduction (Golf Club Deformity) in Distal Femur Fractures.

OBJECTIVES: To describe malreduction of supracondylar distal femur fractures stabilized with lateral femoral locking plates and determine whether a mismatch in axial lateral distal femur anatomy and lateral distal femoral plate design contributes to supracondylar distal femoral fracture malreduction. MATERIALS AND METHODS: OTA/AO 33A were simulated in 7 cadaver femurs and fixed with a lateral distal locking femoral plate placed flush to the lateral femoral condyle (group 1). In group 2, the anterior flange of the plate was externally rotated 10 degrees in relation to the lateral condyle. A motion capture system measured translation and rotation of the articular segment as shaft screws were applied, reducing plate to femoral diaphysis. Articular segment movement was compared between groups using paired Student t test, P < 0.05. A large database of 3D scans of 800 femurs was used to define the relationship of the lateral femoral condyle to the lateral cortical surface of the human femur. RESULTS: Malreduction was observed with anatomic plate application results from medial translation (17 mm) and external rotation (12.2 degrees) (group 1). Modifying plate geometry to match lateral femur anatomy (group 2) improved medial translation by 46% and external rotation by 80%. An analysis of the shape of the 800 distal femurs showed that the average posterior anterior inclination is 16.5 degrees. CONCLUSIONS: Anatomic application of distal femoral plates results in significant malreduction. Modifying the plate design to accommodate 10 degrees slope of lateral distal femur results in partial correction of deformity. Future studies should investigate other means of correcting the malalignment, especially considering the 16.5-degree posterior anterior inclination of the condyle.

Is it necessary to tie the medial row in rotator cuff repair double-row constructs when using suture tape?

PURPOSE: To evaluate the selected biomechanical differences of a double-row trans-osseous equivalent rotator cuff repair with a knotless versus knot-tying medial row using suture tape in regard to repair displacement, stiffness, and ultimate load to failure. METHODS: In 16 fresh-frozen human shoulders (8 matched pairs), double-row rotator cuff repairs were performed with medial-row mattress knots (MK) on one side, the other without (NK). Two DVRT (Differential Variable Reluctance Transducer) sensors were attached between the humerus and 3 mm above the repair site and were used to measure the displacement across the repair during cycling. The biomechanical parameters measured were repair displacement, stiffness, and ultimate load to failure. The supraspinatus was loaded in a similar fashion to previously described protocol using cyclic loading and load to failure testing.1. RESULTS: All data from paired specimens were compared using paired Student t tests. No statistically significant difference (SSD) in displacement across the repair over the 200 cycles of the test was noted between the two groups (MK = 0.591 ± 0.501 mm; NK = 0.439 ± 0.417 mm, p = 0.618). No SSD in stiffness was noted between the two groups (MK = 32.87 ± 6.31 N/mm; NK = 27.98 ± 9.69 N/mm, p = 0.120). No SSD in ultimate load to failure was noted between the two groups (MK = 501.2 ± 126.1 N; NK = 416.8 ± 120.0 N, p = 0.116). CONCLUSION: There was no statistically significant different between knotless versus knotted medial row double row rotator cuff repair constructs using suture tape in regard to displacement across the repair site, stiffness and ultimate load to failure. Despite previous evidence suggesting inferiority of knotless medial row technique using suture constructs, this evidence may support the biomechanical equivalency of knotless medial row technique using suture tape.

Effects of Lumbosacral Arthrodesis on the Biomechanics of the Sacroiliac Joint.

BACKGROUND: It is unclear whether the sacroiliac joint is vulnerable to adjacent segment disease. Clinical studies have suggested that many patients who have undergone lumbar arthrodesis will develop adjacent segment disease, which may contribute to sacroiliac joint degeneration. The purpose of the present study was to examine whether arthrodesis in the lumbar spine results in altered biomechanics at the sacroiliac joint that could contribute to adjacent segment disease within the joint. METHODS: With use of human cadavers in a biomechanical laboratory study, the effects of lower-lumbar arthrodesis and sacroiliac screws on the biomechanics of the sacroiliac joint were assessed. Human cadaveric pelves with lumbar spines were biomechanically tested in flexion-extension, rotation about the vertical axis, and compression along the vertical axis with single and double-leg support. Four conditions were compared: (1) intact, (2) L4-L5 arthrodesis, (3) L4-S1 arthrodesis, and (4) left sacroiliac screw. Construct vertical and horizontal motions at the anterior and posterior surfaces of the sacroiliac joint were measured. RESULTS: Significant measurable increases in motion of the sacroiliac joint related to arthrodesis of the lumbar spine occurred with flexion-extension loading (p < 0.05). No significant changes were observed for rotation about the vertical axis or compression along the vertical axis with single and double-leg support. CONCLUSIONS: After 360°, 1 or 2-level lumbosacral spine arthrodesis, the sacroiliac joint showed a significant increase in rotational motion with flexion-extension loading. Increases in horizontal translation with axial rotation loading and vertical translation with axial compression loading were not significant. CLINICAL RELEVANCE: The risk of significant alteration of normal sacroiliac kinematics should be considered in all patients undergoing 360° lumbosacral arthrodesis.

Comparison of Biomechanical Properties of a Synthetic L3-S1 Spine Model and Cadaveric Human Samples.

Human cadavers currently represent the gold standard for spine biomechanical testing, but limitations such as costs, storage, handling, and high interspecimen variance motivate the development of alternatives. A commercially available synthetic surrogate for the human spine, the Sawbones spine model (SBSM), has been developed. The equivalence of SBSM to a human cadaver in terms of biomechanical behavior has not been fully assessed. The objective of this study is to compare the biomechanics of a lumbar tract of SBSM to that of a cadaver under physiologically relevant mechanical loads. An L3-S1 SBSM and 39 comparable human cadaver lumbar spine tracts were used. Each sample was loaded in pure flexion-extension or torsion. Gravity and follower loads were also included. The movement of each vertebral body was tracked via motion capture. The range of motion (ROM) of each spine segment was recorded, as well as the overall stiffness of each L3-S1 sample. The ROM of SBSM L3-L4 was larger than that found in cadavers in flexion-extension and torsion. For the other spine levels, the ROMs of SBSM were within one standard deviation from the mean values measured in cadavers. The values of structural stiffness for L3-S1 of SBSM were comparable to those of cadaveric specimens for both flexion and torsion. In extension, SBSM was more compliant than cadavers. In conclusion, most of the biomechanical properties of an L3-S1 SBSM model were comparable to those of human cadaveric specimens, supporting the use of this synthetic surrogate for testing applications.

Biomechanical Comparison between Volar Plate Fixator and Nonbridge External Wrist Fixator.

Intra-articular distal radius fractures are difficult to reduce and maintain by nonoperative means. ORIF leaves implants in the patient long after the fracture is healed. External fixation can stabilize the reduced fracture and leaves no long-term implants. The nonbridging fixator (NBX) will provide better reduction and comparable rigidity of fixation to a volar plate for a 5-fragment, OTA 23 C3.2 distal radius fracture. A 5-part distal radius fracture was created in 5 pairs of cadaver arms. One arm was randomly fixed with the NBX fixator; the matched pair was fixed with a volar plate (VPS). Fluoroscopic images recorded the extremes of passive volar-dorsiflexion range of motion (ROM) and radial-ulnar deviation ROM. Each arm was loaded with an axial force at a constant displacement rate until failure. The average reduction of radial tilt achieved for the NBX group was 13.8 ± 4.8° and 6.3 ± 4.7° for VPS; radial length: 3.4 ± 3.7 mm for NBX and 1.9 ± 1.0 mm for VPS; volar tilt: 26.3 ± 12.4° for NBX and 14.0 ± 13.5° for VPS. For NBX, ROM was slightly less after fixation than before fracture. ROM with volar plating was greater after fracture. The peak axial load for NBX was 925 ± 445 N; for VPS, 2,152 ± 1023 N. NBX had minimal effect on ROM and provided adequate strength and restoration of alignment at least as good as VPS for this 5-part fracture model.

Cerclage Cable Tensioning of Intraoperative Hip Arthroplasty Proximal Femoral Fractures: A Cadaveric Model.

Cerclage fixation following intraoperative fracture of the proximal femur during total hip arthroplasty (THA) carries a risk of compromising the femoral blood supply. Thus, we sought to determine the minimum cerclage cable tension required to restore the stability of a cementless femoral stem. Cementless femoral prostheses were implanted in seven proximal femoral cadaver specimens, and a periprosthetic fracture was simulated in the medial cortex. A single cerclage cable was placed just above the lesser trochanter and tensioned and tested at increasing intervals. The implant's torsional stability was determined in the intact bone, prior to fixation, and at each level of cable tension. We found that a single cerclage cable placed above the lesser trochanter can significantly improve, but not fully restore, torsional stability following intraoperative periprosthetic femur fracture during THA. The optimal position for a single cerclage cable appears to be above the lesser trochanter. (Journal of Surgical Orthopaedic Advances 29(4):209-211, 2020).

Supplemental Fixation of Inner Graft Limbs in All-Inside, Quadrupled, Single-Tendon Anterior Cruciate Ligament Reconstruction Graft Construct Yields Improved Biomechanical Properties.

PURPOSE: To compare the time-zero load to failure of a quadrupled, single-tendon, all-inside anterior cruciate ligament (ACL) reconstruction graft construct with (supplemented) and without the incorporation of inner-limb whipstitch sutures (control) into a tibial suspensory fixation button. METHODS: Eight matched pairs of peroneus longus tendons were prepared according to a quadrupled, all-inside ACL soft-tissue graft technique with 1 side serving as a control and the contralateral side supplemented. The constructs were biomechanically tested for strain in the inner and outer limbs during a preconditioning protocol, single-cycle load to failure, and elongation of the whole construct. RESULTS: Ultimate load to failure was significantly higher in the supplemented group: 797.5 ± 49.6 N (95% confidence interval [CI], 763.13-831.87 N) versus 719.6 ± 69.6 N (95% CI, 671.38-767.82 N; P = .044). Less graft elongation at failure was observed in the supplemented group (3.1 ± 1.5 mm; 95% CI, 2.07-4.17 mm) versus the control group (21.0 ± 21.2 mm; 95% CI, 6.31-35.69 mm; P = .052). The number of grafts undergoing a 5-mm or greater change in length at failure was 1 of 8 in the supplemented group versus 5 of 8 in the control group (P = .038). CONCLUSIONS: Inner-limb supplemental tibial fixation results in higher time-zero load to failure and decreased graft elongation in a quadrupled, single-tendon, all-inside ACL reconstruction graft construct. CLINICAL RELEVANCE: The weak point of a single-tendon, quadrupled, all-inside ACL graft construct is the tendon-to-tendon suturing to secure the inner limbs of the graft. Adding supplemental fixation by incorporating the sutures from the inner limb to the tibial suspensory fixation button leads to a higher time-zero load to failure and decreased graft elongation.

Filling Open Screw Holes in the Area of Metaphyseal Comminution Does Not Affect Fatigue Life of the Synthes Variable Angle Distal Femoral Locking Plate in the AO/OTA 33-A3 Fracture Model.

INTRODUCTION: The aim of this study is to evaluate the biomechanical effect of filling locking variable angle (VA) screw holes at the area of metaphyseal fracture comminution in a Sawbones® (Sawbones USA, Vashon, Washington) model (AO/OTA 33A-3 fracture) using a Synthes VA locking compression plate (LCP) (Depuy Synthes, Warsaw, Indiana). MATERIALS AND METHODS: Seven Sawbones® femur models had a Synthes VA-LCP placed as indicated by the manufacturers technique. A 4cm osteotomy was then created to simulate an AO/OTA 33-A3 femoral fracture pattern with metaphyseal comminution. The control group consisted of four constructs in which the open screw holes at the area of comminution were left unfilled; the experimental group consisted of three constructs in which the VA screw holes were filled with locking screws. One of the control constructs was statically loaded to failure at a rate of 5mm/min. A value equal to 75% of the ultimate load to failure was used as the loading force for fatigue testing of 250,000 cycles at 3Hz. Cycles to failure was recorded for each construct and averages were compared between groups. RESULTS: The average number of cycles to failure in the control and experimental groups were 37524±8187 and 43304±23835, respectively (p=0.72). No significant difference was observed with respect to cycles to failure or mechanism of failure between groups. In all constructs in both the control and experimental groups, plate failure reproducibly occurred with cracks through the variable angle holes in the area of bridged comminution. CONCLUSIONS: The Synthes VA-LCP in a simulated AO/OTA 33-A3 comminuted metaphyseal femoral fracture fails in a reproducible manner at the area of comminution through the "honeycomb" VA screw holes. Filling open VA screw holes at the site of comminution with locking screws does not increase fatigue life of the Synthes VA-LCP in a simulated AO/OTA 33-A3 distal femoral fracture. Further studies are necessary to determine whether use of this particular plate is contraindicated when bridging distal femoral fractures with metaphyseal comminution.

Effects of gamma irradiation on the biomechanical properties of peroneus tendons.

PURPOSE: This study was designed to investigate the biomechanical properties of nonirradiated (NI) and irradiated (IR) peroneus tendons to determine if they would be suitable allografts, in regards to biomechanical properties, for anterior cruciate ligament reconstruction after a dose of 1.5-2.5 Mrad. METHODS: Seven pairs of peroneus longus (PL) and ten pairs of peroneus brevis (PB) tendons were procured from human cadavers. The diameter of each allograft was measured. The left side of each allograft was IR at 1.5-2.5 Mrad, whereas the right side was kept aseptic and NI. The allografts were thawed, kept wet with saline, and attached in a single-strand fashion to custom freeze grips using liquid nitrogen. A preload of 10 N was then applied and, after it had reached steady state, the allografts were pulled at 4 cm/sec. The parameters recorded were the displacement and force. RESULTS: The elongation at the peak load was 10.3±2.3 mm for the PB NI side and 13.5±3.3 mm for the PB IR side. The elongation at the peak load was 17.4±5.3 mm for the PL NI side and 16.3±2.0 mm for the PL IR side. For PL, the ultimate load was 2,091.6±148.7 N for NI and 2,122.8±380.0 N for IR. The ultimate load for the PB tendons was 1,485.7±209.3 N for NI and 1,318.4±296.9 N for the IR group. The ultimate stress calculations for PL were 90.3±11.3 MPa for NI and 94.8±21.0 MPa for IR. For the PB, the ultimate stress was 82.4±19.0 MPa for NI and 72.5±16.6 MPa for the IR group. The structural stiffness was 216.1±59.0 N/mm for the NI PL and 195.7±51.4 N/mm for the IR side. None of these measures were significantly different between the NI and IR groups. The structural stiffness was 232.1±45.7 N/mm for the NI PB and 161.9±74.0 N/mm for the IR side, and this was the only statistically significant difference found in this study (P=0.034). CONCLUSION: Our statistical comparisons found no significant differences in terms of elongation, ultimate load, or ultimate stress between IR and NI PB and PL tendons. Only the PB structural stiffness was affected by irradiation. Thus, sterilizing allografts at 1.5-2.5 Mrad of gamma irradiation does not cause major alterations in the tendons' biomechanical properties while still providing a suitable amount of sterilization for anterior cruciate ligament reconstruction.

Biomechanical evaluation of periprosthetic refractures following distal femur locking plate fixation.

INTRODUCTION: Distal femur fractures proximal to total knee femoral component constitutes the most prevalent type of periprosthetic fracture, and plate fixation treatment is associated with a 7.7% incidence of refracture proximal to the plate. The primary objective of this study was to compare proximal fixation techniques of a periprosthetic distal femur fracture plate in an osteoporotic bone model. The secondary objective was to determine the subsequent periprosthetic plate fracture pattern and/or complexity associated with each proximal plate fixation configuration. MATERIALS AND METHODS: A segmental defect was created in 21 synthetic osteoporotic adult femurs 6 cm proximal to the distal femur and all specimens were stabilised with a 246 mm locking femur plate. Fixation in the most proximal hole was varied by use of either a cerclage cable, unicortical locking screw, or a bicortical locking screw. Specimens were tested to failure in simultaneous eccentric compression and torsion. RESULTS: Proximal cerclage fixation demonstrated higher mean maximum axial force at failure (4142.67±178.71 N, p<0.001), stiffness (443.8±61.64 N/mm), and maximum torque (20.9±0.93 N m, p<0.001). Unicortical and bicortical screw refractures occurred at the screw, cerclage wire refractures occurred at the first proximal screw distal to the cerclage. CONCLUSIONS: In periprosthetic distal femur fracture locking plate fixation, proximal hole stabilization with a cerclage wire tolerates significantly higher failure forces while distributing forces distal to the area within the plate fixation. Cerclage wiring may be an option in distal femur periprosthetic fractures to alleviate stress risers in vulnerable bone.

The effect of viscosity on cement penetration in total knee arthroplasty, an application of the squeeze film effect.

The authors present a prospective randomized blinded cadaver study designed to evaluate the engineering concept of a squeeze film effect and the effect of cement viscosity on cement penetration in total knee arthroplasty. This was done in response to an earlier clinical study demonstrating inferior tibial cement penetration using early, often liquid, phase cement. Paired cadaver tibias were implanted with the tibial component using either liquid or dough phase cement. Based on an AP fluoroscopic image, the dough phase cement penetrated deeper than liquid in all four zones. This was statistically significant in zones 1, 2 and 3. Deeper cement penetration has been shown to provide a stronger cement-bone interphase. As a result dough phase cement is recommended to obtain optimal cement penetration.

Biomechanical analysis of four- versus six-screw constructs for short-segment pedicle screw and rod instrumentation of unstable thoracolumbar fractures.

BACKGROUND CONTEXT: Conventionally, short-segment fusion involves instrumentation of one healthy vertebra above and below the injured vertebra, skipping the injured level. This short-segment construct places less surgical burden on the patient compared with long-segment constructs, but is less stable biomechanically, and thus has resulted in clinical failures. The addition of two screws placed in the fractured vertebral body represents an attempt to improve the construct stiffness without sacrificing the benefits of short-segment fusion. PURPOSE: To determine the biomechanical differences between four- and six-screw short-segment constructs for the operative management of an unstable L1 fracture. STUDY DESIGN: Biomechanical study of instrumentation in vertebral body cadaveric models simulating an L1 axial load injury pattern. METHODS: Thirteen intact spinal segments from T12 to L2 were prepared from fresh-frozen cadaver spines. An axial load fracture of at least 50% vertebral body height was produced at L1 and then instrumented with pedicle screws. Specimens were evaluated in terms of construct stiffness, motion, and rod strain. Two conditions were tested: a four-screw construct with no screws at the L1 fractured body (4S) and a six-screw construct with screws at all levels (6S). The two groups were compared statistically by paired Student t test. RESULTS: The mean stiffness in flexion-extension was increased 31% (p<.03) with the addition of the two pedicle screws in L1. Relative motion in terms of vertical and axial rotations was not significantly different between the two groups. The L1-L2 rod strain was significantly increased in the six-screw construct compared with the four-screw construct (p<.001). CONCLUSIONS: In a cadaveric L1 axial load fracture model, a six-screw construct with screws in the fractured level is more rigid than a four-screw construct that skips the injured vertebral body.

Histologic, biomechanical, and biological evaluation of fan-folded iliotibial band allografts for anterior cruciate ligament reconstruction.

PURPOSE: The purpose of this study was to thoroughly characterize the fan-folded iliotibial band (FITB) allograft and compare it with anterior tibialis tendons (ATs) and native anterior cruciate ligaments (ACLs) to determine whether it measures up to those tissues. METHODS: We compared the histologic structure, tensile strength to failure, creep, and stress-relaxation properties of FITBs with those of ATs and ACLs. In vitro cytotoxicity and biocompatibility of FITBs were also compared with ATs. RESULTS: No structural difference was observed between the tissues studied. FITB ultimate tensile strength (3,459 ± 939 N) was not significantly different (P > .9999) from ultimate tensile strength of ATs (3,357 ± 111 N) and was significantly greater (P = .0005) than that of ACLs (886 ± 254 N). No significant difference (P > .9999) was observed in the increase in length resulting from creep testing between FITBs (9.5 ± 3.0 mm) and ATs (9.7 ± 4.0 mm). During stress-relaxation testing, FITBs reached 181 ± 46 N, which was not significantly different (P > .9999) from ATs (166 ± 40 N). Finally, we showed that cytotoxicity of FITBs and ATs was negligible. In vitro biocompatibility of FITBs and ATs was very good, whereas FITBs had a higher propensity to favor the attachment and infiltration of cells that proliferated for at least 4 weeks on their contact. CONCLUSIONS: We found that FITBs, ACLs, and ATs shared a similar structure made of aligned collagen fibers. No significant difference was observed between FITB and AT ultimate tensile strength, creep, and stress-relaxation viscoelastic properties. Ultimate tensile strength to failure of ACLs was lower than that of FITBs and ATs, whereas ACLs were superior to both FITBs and ATs during creep and stress-relaxation testing. FITBs and ATs showed low cytotoxicity and excellent biocompatibility in vitro, with a somewhat higher propensity of FITBs to favor cell attachment and infiltration over time. CLINICAL RELEVANCE: This study suggests that FITBs have the potential to perform as well as ATs for ACL reconstruction.

Biomechanical study of 4-hole pubic symphyseal plating: locked versus unlocked constructs.

To the authors' knowledge, no published studies have examined the use of locking plates on injuries of the anterior pelvic ring. The purpose of this study was to determine whether locked plates provide enhanced stability in the treatment of pubic symphyseal disruptions. Completely unstable pelvic injuries were simulated in pelvic Sawbones (model 1301; Pacific Research Laboratories, Vashon, Washington) and 2 different fixation constructs used for anterior fixation (4-hole, 3.5-mm pubic symphysis plate with all locked or all unlocked screws). Adjunctive sacroiliac screw fixation with a single 7.3-mm screw placed into S1 was used in all specimens. Specimens were analyzed for motion at the pubic symphysis and sacroiliac joints using a Material Testing System (MTS Systems Corporation, Eden Prairie, Minnesota). Each specimen was subjected to compressive loading in a single-limb stance. Side loading was also examined. The main outcome measurement was motion at the pubic symphysis and sacroiliac joints and overall construct stiffness. No significant difference existed in overall construct stiffness between the 2 methods of pubic symphysis fixation. The motions at the pubic symphysis or injured sacroiliac joints were not significantly different. In addition, motion at the pubic symphysis joint with lateral load was not improved with a locking construct.No significant difference existed between 4-hole locked or unlocked constructs used for fixation of the pubic symphysis. No apparent advantage of locking screws exists for disruptions of the pubic symphysis, and recent reports have questioned the possibility of catastrophic failure.

Comparison of 2 forearm reconstructions for longitudinal radioulnar dissociation: a cadaver study.

PURPOSE: We present the results of a cadaveric study of 2 forearm reconstructions with radial head replacement for longitudinal radioulnar dissociation injuries. METHODS: We created a simulated longitudinal radioulnar dissociation injury in 8 cadaver forearms. Two reconstructions were performed alternately on each arm: patellar tendon interosseous ligament complex reconstruction and the Herbert sling extensor retinaculum plication. We performed mechanical testing in a materials testing machine with and without a radial head replacement, and measured ulnocarpal impaction force through 2 distal ulna strain gauges. We determined relative radioulnar displacement using live fluoroscopic analysis of implanted stainless-steel beads. RESULTS: Relative radioulnar longitudinal displacement in the destabilized forearms was 10.7 compared with 0.7 mm before creating the injury. A prosthetic radial head replacement alone decreased the displacement by 75% to 2.7 mm. Interosseous ligament reconstruction alone reduced the displacement to 5.1 mm and to 1.3 mm when combined with a radial head implant. The Herbert sling alone did not improve longitudinal stability. The distal ulna force in the native arm was 17 N, or 17% of the force across the wrist. The interosseous ligament reconstruction restored the force to 21 N, whereas the Herbert sling only marginally decreased the ulna impaction force to 45 N. Adding a radial head decreased the distal ulna force to 7 N for the patellar tendon interosseous ligament reconstruction, and 2 N for the Herbert sling. CONCLUSIONS: In longitudinal radioulnar dissociation injuries, the radial head is an important stabilizer and should be repaired or replaced to minimize radial shortening and ulnar impaction force. Patellar tendon interosseous ligament reconstruction effectively restores the ulnocarpal force distribution and markedly reduces longitudinal instability at the distal radioulnar joint. Combined with radial head arthroplasty, the construct has stability similar to an intact forearm. The Herbert sling did not improve longitudinal stability in this testing construct. CLINICAL RELEVANCE: Treatment of longitudinal radioulnar dissociation may benefit from radial head replacement and interosseous ligament reconstruction using a patellar tendon graft.

Building a biomechanical model.

This article is based on an invited presentation at the Biomechanics Session for the Basic Science Focus Forum held at the Orthopaedic Trauma Association meeting, 2010. It is not intended to be a scientific presentation of any specific investigation. It presented aspects of several types of investigations to illustrate the variety of biomechanical models that are used, and what value can be derived from those models. All models have limitations in what they try to portray. In order for any model to provide useful information, it must stand some type of validation of its ability to behave similar to real world experiences. The advantages and disadvantages of each model must be described to the best of the investigators ability-so that the readers can determine how the information may be used in the real world.