RESUMEN
In a variety of industries, including transportation, agriculture, and manufacturing, diesel engines are often employed. Due of rising prices and environmental concerns, researchers examined whether biodiesels might replace diesel. The current study looks into American Saffron Oil's feasibility as a feedstock for biodiesel production. The transesterification technique is used to extract American saffron oil methyl este(ASOME), which is then examined for its physical and chemical properties in accordance with ASTM standards. Diesel fuel and American Saffron Oil methyl ester are mixed on a volume basis to create a variety of fuel blends, including B20, B40, and B60. The test results showed that the 20 % ASOME mix had better performance and reduced emissions. Also, utilizing DIESEL-RK simulation software, diesel engine tests are conducted for the B20, B40, and B60 under identical operating circumstances. Moreover, diesel engine testing for the B20, B40, and B60 are carried out using DIESEL-RK simulation software under comparable operating circumstances. Results of simulation software tests show improved engine performance and reduced pollutants. When experimental data is compared to DIESEL-RK modeling software, it is found that brake thermal efficiency increased by 5.7 % and emissions of hydrocarbon and carbon monoxide decreased by 2.5 % and 14.3 %, respectively.
RESUMEN
The focus of the study in this article is analyzing the electrochemical properties of molybdenum disulfide on miscible poly(methyl methacrylate)-poly(lactic acid) blends for supercapacitors. The interaction between molybdenum disulfide and miscible poly(methyl methacrylate)-poly(lactic acid) blends, affinity toward water, surface morphology, and mechanical properties are inspected by Fourier transform infrared spectroscopy, water contact angle, scanning electron microscopy, and universal testing machine, respectively. Among the developed membranes, 0.75 wt% of molybdenum disulfide on poly(methyl methacrylate)-poly(lactic acid) shows better electrochemical performances. It exhibits a maximum specific capacitance of 255.5 F g-1 at a current density of 1.00 mA g-1, maximum energy density of 22.7 Wh kg-1, and maximum power density of 360 W kg-1. A cycle study reveals 92% capacitance retention after 2500 cycles. The designed supercapacitor device shows a maximum specific capacitance of 1240 µF g-1 at a current density of 0.5 µA g-1, maximum energy density of 43 µWh kg-1, and maximum power density of 700 µW kg-1. Flexible membranes of molybdenum disulfide are expected to be a potent combination for supercapacitor applications.
RESUMEN
The present investigation focuses on the manufacturing and mechanical evaluation of epoxy-based composites reinforced with fiberglass with and without various particle fillers. The study explores the potential use of industrial wastes, such as coal powder (CP), coal fly ash (CFA), bagasse ash (BA), palm fruit ash (PFA), ash from rice husks (RHA), bone ash (BoA), marble/granite powder (MP), combinations of coal fly ash and coal powder (CFACP), blends of coal fly ash and marble powder (CFAMP), and combinations of coal fly ash and bone ash (CFABoA).The use of industrial factory wastes as a filler in polymer composite materials is becoming more and more common due to the improvement in structural characteristics compared to the pure epoxy-e-glass fiber composites. Composite manufacturing costs might be drastically reduced by using the above industrial wastes as reinforcing material, which would also solve the problems related to their disposal and ecological pollution. In previous research investigations, the comparative mechanical characteristic analysis of hybrid composites filled with two or more fillers has not been studied, which motivated us to take up the research on incorporation of the above listed industrial wastes as fillers. Different concentrations of these fillers are investigated, and the composites are formed successfully using a manual hand-layup approach. The mechanical properties assessed in accordance with ASTM Standards include micro-Vickers hardness (Hv), impact strength (IS), bending strength (TS), flexibility or flexural strength (FS), and interlaminar shear strength (ILSS). The form and amount of filler provided to the composite are considered when comparing each property of particle-loaded glass-reinforced epoxy composites. Some key findings from the investigation include: (1) Tensile Strength: unfilled composites exhibit a tensile strength of 252.19 MPa, marble powder causes the greatest drop in tensile strength, and CFACP-filled composites at 5 wt % yield the highest tensile strength of 251.42 MPa. (2) Flexural Strength: CFABoA-filled composites exhibit the highest peak bending strength of 860.22 MPa at 10 wt % and Peak ILSS of 34.317 MPa at 5 wt % is observed with CFABoA-filled composites. (3) Impact Strength and Hardness: CFACP-filled composites at 10 wt % show the maximum impact strength (2100 J/m) and hardness (62 Hv). (4) Effect of the Filler Percentage: mechanical characteristics of composites improve with increasing weight percentage of filler material, and Glass fiber-reinforced epoxy composites can be replaced with glass fiber-reinforced and particle-filled polymer-based hybrid composites for structural purposes. (5) Cost Considerations: hybrid composites based on CFACP-filled E-glass fiber-reinforced epoxy can be used instead of E-glass fiber-reinforced epoxy composites to reduce fabrication costs and "ER" epoxy resin usage. (6) Application Recommendation: the study suggests the use of CFACP-filled E-glass fiber-reinforced epoxy composites for constructing end posts in rail insulation junctions. In conclusion, the investigation provides valuable insights into the mechanical properties of epoxy-based composites with various fillers, offering potential applications in structural components with improved characteristics and cost-effectiveness.
RESUMEN
In the present investigation, the corrosion tendency of mild steel under acidic pH was studied by employing unused expired amiodarone (EAD) drug as a potential corrosion inhibitor by adopting the weight loss measurement method. The corrosion inhibition efficiency (IE) of the formed protective film (EAD) on the steel surface was analyzed using potentiodynamic polarization and AC-impedance spectroscopy studies. The surface morphology of the mild steel before and after corrosion (in 1.0 M HCl) was analyzed via scanning electron microscopy-energy dispersive X-ray spectroscopy (SEM-EDAX), atomic force microscopy (AFM), and thermodynamic studies. The weight loss measurement under different concentrations of EAD indicated that an excellent inhibition was displayed at a concentration of 0.001 M, and the IE was found to depend on both the concentration and molecular structure of EAD. A potentiodynamic polarization study revealed that EAD predominantly acted as a cathode inhibitor, and electrochemical impedance spectroscopy (EIS) confirmed the adsorption of EAD on the surface of mild steel, which obeyed Temkin's adsorption isotherm model. The calculated thermodynamic parameters revealed that adsorption was spontaneous and exothermic.
RESUMEN
Biodiesel production through the synthesis of Datura stramonium L. oil is studied to explore the most efficient approaches to suggest an alternate feedstock for biodiesel production. The main objective of this work is to optimize the process variables of biodiesel synthesis by using some statistical approach (Taguchi method, grey relational analysis (GRA), and response surface methodology (RSM) analyzing three parameters, i.e., alcohol-to-oil molar ratio, catalyst (NaOH) concentration, and process temperature for achieving maximum biodiesel derived from Datura stramonium L. oil. The transesterification process is applied by using an ultrasonic-assisted technique. Grey relational analysis (GRA) was successfully applied with the Taguchi method resulting in the optimum combination of A2B1C1. Based on the findings, the best operating conditions for transesterifying are attained with the RSM approach consisting of a 5.697:1 molar ratio (level 2), 0.3 (wt.%) NaOH concentration (level 1), and 70 °C process temperature (level 1). With a value of 87.02%, these ideal operating conditions produce the maximum yield as compared to grey relational analysis (GRA) yields 83.99%. The obtained results have been verified through the characterization of oil and biodiesel as well. Also, the fuel qualities of DSL biodiesel were identified and assessed. DSL oil was found 137.6 degrees of unsaturation during fatty acid profile analysis. DSL biodiesel was found the best kinematic viscosity (4.2 mm2/s) and acid value (0.49) when compared to Karanja and palm biodiesel. D. stramonium L. was recognized as a suitable species for biodiesel feedstock according to the findings.
Asunto(s)
Datura stramonium , Biocombustibles , Hidróxido de Sodio , Esterificación , Ácidos Grasos , CatálisisRESUMEN
BACKGROUND: The scientific revolution in the treatment of many illnesses has been significantly aided by stem cells. This paper presents an optimal control on a mathematical model of chemotherapy and stem cell therapy for cancer treatment. OBJECTIVE: To develop effective hybrid techniques that combine the optimal control theory (OCT) with the evolutionary algorithm and multi-objective swarm algorithm. The developed technique is aimed to reduce the number of cancerous cells while utilizing the minimum necessary chemotherapy medications and minimizing toxicity to protect patients' health. METHODS: Two hybrid techniques are proposed in this paper. Both techniques combined OCT with the evolutionary algorithm and multi-objective swarm algorithm which included MOEA/D, MOPSO, SPEA II and PESA II. This study evaluates the performance of two hybrid techniques in terms of reducing cancer cells and drug concentrations, as well as computational time consumption. RESULTS: In both techniques, MOEA/D emerges as the most effective algorithm due to its superior capability in minimizing tumour size and cancer drug concentration. CONCLUSION: This study highlights the importance of integrating OCT and evolutionary algorithms as a robust approach for optimizing cancer chemotherapy treatment.
Asunto(s)
Algoritmos , Antineoplásicos , Neoplasias , Humanos , Neoplasias/terapia , Neoplasias/tratamiento farmacológico , Antineoplásicos/uso terapéutico , Simulación por Computador , Terapia Combinada , Trasplante de Células Madre/métodos , Modelos Biológicos , Inteligencia ArtificialRESUMEN
BACKGROUND: This study explores the dynamics of a mathematical model, utilizing ordinary differential equations (ODE), to depict the interplay between cancer cells and effector cells under chemotherapy. The stability of the equilibrium points in the model is analysed using the Jacobian matrix and eigenvalues. Additionally, bifurcation analysis is conducted to determine the optimal values for the control parameters. OBJECTIVE: To evaluate the performance of the model and control strategies, benchmarking simulations are performed using the PlatEMO platform. METHODS: The Pure Multi-objective Optimal Control Problem (PMOCP) and the Hybrid Multi-objective Optimal Control Problem (HMOCP) are two different forms of optimal control problems that are solved using revolutionary metaheuristic optimisation algorithms. The utilization of the Hypervolume (HV) performance indicator allows for the comparison of various metaheuristic optimization algorithms in their efficacy for solving the PMOCP and HMOCP. RESULTS: Results indicate that the MOPSO algorithm excels in solving the HMOCP, with M-MOPSO outperforming for PMOCP in HV analysis. CONCLUSION: Despite not directly addressing immediate clinical concerns, these findings indicates that the stability shifts at critical thresholds may impact treatment efficacy.
Asunto(s)
Algoritmos , Modelos TeóricosRESUMEN
In this research, activated carbon (AC) was synthesized from ligno-cellulosic residues of Adansonia kilima (Baobab) wood chips (AKTW) using two-step semi-carbonization and subsequent pyrolysis using microwave-induced heating (MWP) in the presence of a mild activating agent of K2CO3. The influence of process input variables of microwave power (x1), residence time (y1), and amount of K2CO3 (z1) were analysed to yield superior quality carbon having maximum removal efficiencies (R1) for lead (II) cations from waste effluents, fixed carbon percentages (R2), and carbon yield percentages (R3). Analysis of variance (ANOVA) was used to develop relevant mathematical models, with an appropriate statistical assessment of errors. Level factorial response surface methodology (RSM) relying on the Box-Behnken design (BBD) was implemented for the experimental design. The surface area and porous texture of the samples were determined using Brunauer, Emmett, and Teller (BET) adsorption/desorption curves based on the N2 isotherm. Surface morphological structure was observed using field emission scanning electron microscopic (FESEM) analysis. Thermogravimetric analysis (TGA) was carried out to observe the thermal stability of the sample. Change in the carbon content of the samples was determined using ultimate analysis. X-ray diffraction (XRD) analysis was performed to observe the crystalline and amorphous texture of the samples. The retention of a higher proportion of fixed carbon (80.01%) ensures that the synthesized adsorbent (AKTWAC) will have a greater adsorption capacity while avoiding unwanted catalytic activity for our synthesized final sample.
RESUMEN
The phase change of all-inorganic cesium lead halide (CsPbI3) thin film from yellow δ-phase to black γ-/α-phase has been a topic of interest in the perovskite optoelectronics field. Here, the main focus is how to secure a black perovskite phase by avoiding a yellow one. In this work, we fabricated a self-doped CsPbI3 thin film by incorporating an excess cesium iodide (CsI) into the perovskite precursor solution. Then, we studied the effect of organic additive such as 1,8-diiodooctane (DIO), 1-chloronaphthalene (CN), and 1,8-octanedithiol (ODT) on the optical, structural, and morphological properties. Specifically, for elucidating the binary additive-solvent solution thermodynamics, we employed the Flory-Huggins theory based on the oligomer level of additives' molar mass. Resultantly, we found that the miscibility of additive-solvent displaying an upper critical solution temperature (UCST) behavior is in the sequence CN:DMF > ODT:DMF > DIO:DMF, the trends of which could be similarly applied to DMSO. Finally, the self-doping strategy with additive engineering should help fabricate a black γ-phase perovskite although the mixed phases of δ-CsPbI3, γ-CsPbI3, and Cs4PbI6 were observed under ambient conditions. However, the results may provide insight for the stability of metastable γ-phase CsPbI3 at room temperature.
RESUMEN
BACKGROUND: Coronary arteries disease has been reported as one of the principal roots of deaths worldwide. OBJECTIVE: The aim of this study is to analyze the multiphase pulsatile blood flow in the left coronary artery tree with stenosis. METHODS: The 3D left coronary artery model was reconstructed using 2D computerized tomography (CT) scan images. The Red Blood Cell (RBC) and varying hemodynamic parameters for single and multiphase blood flow conditions were analyzed. RESULTS: Results asserted that the multiphase blood flow modeling has a maximum velocity of 1.017 m/s and1.339 m/s at the stenosed region during the systolic and diastolic phases respectively. The increase in Wall Shear Stress (WSS) observed at the stenosed region during the diastole phase as compared during the systolic phase. It was also observed that the highest Oscillatory Shear Index (OSI) regions are found in the downstream area of stenosis and across the bifurcations. The increase in RBCs velocity from 0.45 m/s to 0.6 m/s across the stenosis was also noticed. CONCLUSION: The computational multiphase blood flow analysis improves the understanding and accuracy of the complex flow conditions of blood elements (RBC and Plasma) and provides the progression of the disease development in the coronary arteries. This study helps to enhance the diagnosis of the blocked (stenosed) arteries more precisely compared to the single-phase blood flow modeling.
Asunto(s)
Vasos Coronarios , Modelos Cardiovasculares , Humanos , Vasos Coronarios/diagnóstico por imagen , Constricción Patológica/diagnóstico por imagen , Velocidad del Flujo Sanguíneo/fisiología , Hemodinámica , Flujo Pulsátil , Simulación por Computador , Estrés MecánicoRESUMEN
Graphene-based fillers possess exceptional properties that encourage researchers toward their incorporation in glass-epoxy (GE) polymer composites. Regarding the mechanical and wear properties of glass-epoxy composites, the effect of graphene oxide (GO) reinforced in glass-epoxy was examined. A decrease in tensile modulus and increase in tensile strength was reported for 1 wt. % of GO. A shift in glass transition temperature Tg was observed with the addition of GO. The cross-link density and storage modulus of the composite decreased with the addition of GO. The decrease in dissipation energy and wear rate was reported with the increase in GO concentration. A simple one-dimensional damage model of nonlinear nature was developed to capture the stress-strain behavior of the unfilled and filled glass-epoxy composite. Tensile modulus E, Weibull scale parameter σo, and Weibull shape parameter ß were considered to develop the model. Finally, to understand the failure mechanisms in GO-filled composites, a scanning electron microscopic (SEM) examination was carried out for tensile fractured composites.
RESUMEN
The present study investigates the CNC milling performance of the machining of AISI 316 stainless steel using a carbide cutting tool insert. Three critical machining parameters, namely cutting speed (v), feed rate (f) and depth of cut (d), each at three levels, are chosen as input machining parameters. The face-centred central composite design (FCCCD) of the experiment is based on response surface methodology (RSM), and machining performances are measured in terms of material removal rate (MRR) and surface roughness (SR). Analysis of variance, response graphs, and three-dimensional surface plots are used to analyse experimental results. Multi-response optimization using the data envelopment analysis based ranking (DEAR) approach is used to find the ideal configuration of the machining parameters for milling AISI 316 SS. The variables v = 220 m/min, f = 0.20 mm/rev and d = 1.2 mm were obtained as the optimal machine parameter setting. Study reveals that MRR is affected dominantly by d followed by v. For SR, f is the dominating factor followed by d. SR is found to be almost unaffected by v. Finally, it is important to state that this work made an attempt to successfully machine AISI 316 SS with a carbide cutting tool insert, to investigate the effect of important machining parameters on MRR and SR and also to optimize the multiple output response using DEAR method.
RESUMEN
Recent advances in aircraft materials and their manufacturing technologies have enabled progressive growth in innovative materials such as composites. Al-based, Mg-based, Ti-based alloys, ceramic-based, and polymer-based composites have been developed for the aerospace industry with outstanding properties. However, these materials still have some limitations such as insufficient mechanical properties, stress corrosion cracking, fretting wear, and corrosion. Subsequently, extensive studies have been conducted to develop aerospace materials that possess superior mechanical performance and are corrosion-resistant. Such materials can improve the performance as well as the life cycle cost. This review introduces the recent advancements in the development of composites for aircraft applications. Then it focuses on the studies conducted on composite materials developed for aircraft structures, followed by various fabrication techniques and then their applications in the aircraft industry. Finally, it summarizes the efforts made by the researchers so far and the challenges faced by them, followed by the future trends in aircraft materials.
RESUMEN
The resistance to delamination in polymer composite depends on their constituents, manufacturing process, environmental factors, specimen geometry, and loading conditions. The manufacturing of laminated composites is usually carried out at an elevated temperature, which induces thermal stresses in composites mainly due to a mismatch in the coefficient of thermal expansion (CTE) of fiber and matrix. This work aims to investigate the effect of these process-induced stresses on mode-I interlaminar fracture toughness (GI) of Glass-Carbon-Epoxy (GCE) and Glass-Epoxy (GE) composites. These composites are prepared using a manual layup technique and cured under room temperature, followed by post-curing using different curing conditions. Double cantilever beam (DCB) specimens were used to determine GI experimentally. The slitting technique was used to estimate residual stresses (longitudinal and transverse direction of crack growth) inherited in cured composites and the impact of these stresses on GI was investigated. Delaminated surfaces of composites were examined using a scanning electron microscopy (SEM) to investigate the effect of post-curing on the mode-I failure mechanism. It was found that GI of both GE and GEC composites are sensitive to the state of residual stress in the laminas. The increase in the GI of laminates can also be attributed to an increase in matrix deformation and fiber-matrix interfacial bond with the increase in post-curing temperature.
RESUMEN
Aluminum metal matrix composites are potential materials for aerospace and automobile industrial applications due to their enhanced mechanical and tribological properties. Aluminum reinforced with silicon carbide particles has been developed with enhanced mechanical and tribological behavior, but it lacks wettability between matrix and reinforcement causing weak bonding, which reduces the degree of enhancement. The objectives of this study were to fabricate aluminum-based metal matrix composites with enhanced wettability at varying stirring speeds (350, 450, 550 rpm), stirring time (5, 10, 15 min), weight percentage of SiC (0, 5, 10 wt.%), and weight percentage of MoS2 (0, 2, 4 wt.%). Nine samples were fabricated using stir casting based on Taguchi L9 orthogonal array. Hardness, tensile strength, and wear rate of the developed composite were investigated and analyzed as a single response characteristic using Taguchi's signal-to-noise ratio and as a multi-response characteristic using hybrid Taguchi-grey relational analysis (HTGRA). The results revealed that the addition of SiC in the composite produced better hardness, tensile strength, and wear rate. The addition of MoS2 in the composite showed better hardness and tensile strength only up to 2 wt.% of MoS2, and in the case of wear rate, the addition of MoS2 in the composite up to 4% showed better wear resistance. Al-SiC-MoS2 hybrid composite shows better enhancement in hardness, tensile strength, and wear resistance than the Al-SiC composite.
RESUMEN
In this study, compacted hematite (Fe2O3) preforms were made and sintered at various temperatures, such as 1250 °C and 1300 °C, using both conventional and microwave sintering methods. The density, porosity, microhardness, cold crushing strength, microphotographs, and X-ray diffraction (XRD) analysis of the sintered preforms were used to evaluate the performance of the two sintering methods. It was found that microwave sintered preforms possessed lesser porosity and higher density than conventionally sintered preforms owing to uniform heating of the powdered ore in microwave sintering method. Furthermore, it was also observed that microwave sintered preforms exhibited relatively higher cold crushing strength and hardness than conventionally sintered preforms. Thus, the overall results revealed that microwave sintering yielded better properties considered in the present study.
RESUMEN
Functionalized magnetite nanoparticles (Fe3O4) were prepared using the coprecipitation method followed by functionalization with a multipotent antioxidant (MPAO). The MPAO was synthesized and analyzed using FTIR and NMR techniques. In this study, the functionalized nanoparticles (IONP@AO) were produced and evaluated using the FTIR, XRD, Raman, HRTEM, FESEM, VSM, and EDX techniques. The average determined particle size of IONP@AO was 10 nanometers. In addition, it demonstrated superparamagnetic properties. The magnitude of saturation magnetization value attained was 45 emu g-1. Virtual screenings of the MPAO's potential bioactivities and safety profile were performed using PASS analysis and ADMET studies before the synthesis step. For the DPPH test, IONP@AO was found to have a four-fold greater ability to scavenge free radicals than unfunctional IONP. The antimicrobial properties of IONP@AO were also demonstrated against a variety of bacteria and fungi. The interaction of developed nanoantioxiants with biomolecules makes it a broad-spectrum candidate in biomedicine and nanomedicine.
Asunto(s)
Antiinfecciosos/farmacología , Antioxidantes/farmacología , Nanopartículas de Magnetita/química , Propiedades de SuperficieRESUMEN
Diesel fuel blends with biodiesels are expected to mitigate the rising price and demand of conventional fuels. Biodiesel fuel blends are also known to reduce engine emissions. Biodiesel is produced from various sources, one of which is Calophyllum Inophyllum methyl ester biodiesel (CIMEBD). Even though it serves to mitigate the energy crisis and has a low overall carbon footprint, CIMEBD has certain negative issues relating to engine performance and emission characteristics. Nanoparticle (NP) addition is known to enhance the engine performance characteristics of next generation biofuels. CeO2 (cerium oxide or ceria) NPs of varying size are used in this study along with 25:75 biodiesel-diesel (BD) blend and a fixed NP concentration of 90 ppm. Ceria NP-doped fuel is shown to have better engine performance compared to diesel and BD blend for all load conditions. Improvements in brake thermal efficiency (BTE) and brake-specific fuel consumption (BSFC) values equal to +30% and -46%, respectively, are observed from experiments for ceria NP-doped biodiesel, compared to diesel-biodiesel (BD) blend. Ceria NPs in the 20 to 40 nm range have optimum engine performance characteristics. Compared to BD blends, NP-doped biodiesel shows improvements in NOx, CO, CO2, UHC, and soot parameters up to -35%, -60%, -35%, -38%, and -40%, respectively. Likewise, the optimum size of ceria NPs is in the range 20-40 nm for better emission characteristics.
RESUMEN
BACKGROUND: The blood flow in the human artery has been a subject of sincere interest due to its prime importance linked with human health. The hemodynamic study has revealed an essential aspect of blood flow that eventually proved to be paramount to make a correct decision to treat patients suffering from cardiac disease. OBJECTIVE: The current study aims to elucidate the two-way fluid-structure interaction (FSI) analysis of the blood flow and the effect of stenosis on hemodynamic parameters. METHODS: A patient-specific 3D model of the left coronary artery was constructed based on computed tomography (CT) images. The blood is assumed to be incompressible, homogenous, and behaves as Non-Newtonian, while the artery is considered as a nonlinear elastic, anisotropic, and incompressible material. Pulsatile flow conditions were applied at the boundary. Two-way coupled FSI modeling approach was used between fluid and solid domain. The hemodynamic parameters such as the pressure, velocity streamline, and wall shear stress were analyzed in the fluid domain and the solid domain deformation. RESULTS: The simulated results reveal that pressure drop exists in the vicinity of stenosis and a recirculation region after the stenosis. It was noted that stenosis leads to high wall stress. The results also demonstrate an overestimation of wall shear stress and velocity in the rigid wall CFD model compared to the FSI model.
Asunto(s)
Vasos Coronarios , Modelos Cardiovasculares , Velocidad del Flujo Sanguíneo , Simulación por Computador , Vasos Coronarios/diagnóstico por imagen , Corazón , Hemodinámica , Humanos , Flujo Pulsátil , Estrés MecánicoRESUMEN
Water pipe surface deterioration is the result of continuous electrochemical reactions attacking the surface due to the interaction of the pipe surface with environments through the time function. The study presents corrosion characterization at the surface and sub-surface of damaged ductile iron pipe (DIP) and galvanized steel (GS) pipes which served for more than 40 and 20 years, respectively. The samples were obtained from Addis Ababa city water distribution system for the analysis of corrosion morphology patterns at different surface layers. Mountains 8.2 surface analysis software was utilized based on the ISO 25178-2 watershed segmentation method to investigate corrosion features of damaged pipe surface and to evaluate maximum pit depth, area, and volume in-situ condition. Based on the analysis maximum values of pit depth, area and volume were 380 µ m, 4000 µm2, and 200,000 µm3, respectively, after 25% loss of the original 8 mm thickness of DIP. Similarly, the pit depth of the GS pipe was 390 µm whereas the maximum pit area and volume are 4000 µm2 and 16,000 µm3, respectively. In addition, characterizations of new pipes were evaluated to study microstructures by using an optical microscope (OM), and a scanning electron microscope (SEM) was used to analyze corrosion morphologies. Based on the SEM analysis, cracks were observed at the sub-surface layer of the pipes. The results show that uniform corrosion attacked the external pipe surface whereas pitting corrosion damaged the subsurface of pipes. The output of this study will be utilized by water suppliers and industries to investigate corrosion phenomena at any damage stage.