Lithium Chloride-Substituted Methylammonium Lead Tribromide Perovskites for Dual γ/Neutron Sensing.

Dual γ/neutron radiation sensors are a critical component of the nuclear security mission to prevent the proliferation of a special nuclear material (SNM). While high-performing semiconductors such as high purity germanium (HPGe) and CdZnTe (CZT) already exist in the nuclear security enterprise, their high cost and/or logistical burdens make widespread deployment difficult to achieve. Metal lead halide perovskites (MHPs) have attracted interest in recent years to address this challenge. In particular, methylammonium lead tribromide (CH3NH3PbBr3, MAPbBr3, or MAPB) has been widely evaluated for its radiation sensing capabilities. While previous studies have demonstrated low-energy X-ray and α particle sensing of MAPB-based detectors and several studies discuss the potential for γ ray sensing, neutron sensing of this material has been rarely explored. Here, we explore the incorporation of lithium in the form of LiCl into the MAPB structure to add thermal neutron sensitivity. Characterizations of the lithium-doped MAPB crystals demonstrate that quality growths are achievable with single crystals that exhibit high crystallinity, no phase change, and high macroscopic bulk quality. Finally, we report on the first demonstrated γ ray and thermal neutron sensing based on lithium-doped MAPB single crystals, which is a significant milestone in the development of 3D dual γ/neutron MHP sensors.

Pulse pileup analysis for a double-sided silicon strip detector using variable pulse shapes.

Due to pulse pileup, photon counting detectors (PCDs) suffer from count loss and energy distortion when operating in high count rate environments. In this paper, we studied the pulse pileup of a double-sided silicon strip detector (DSSSD) to evaluate its potential application in a mammography system. We analyzed the pulse pileup using pulses of varied shapes, where the shape of the pulse depends on the location of photon interaction within the detector. To obtain the shaped pulses, first, transient currents for photons interacting at different locations were simulated using a Technology Computer-Aided Design (TCAD) software. Next, the currents were shaped by a CR-RC2 shaping circuit, calculated using Simulink. After obtaining these pulses, both the different orders of pileup and the energy spectrum were calculated by taking into account the following two factors: 1) spatial distribution of photon interactions within the detector, and 2) time interval distribution between successive photons under a given photon flux. We found that for a DSSSD with thickness of 300 µm, pitch of 25 µm and strip length of 1 cm, under a bias voltage of 50 V, the variable pulse shape model predicts the fraction free of pileup can be > 90 % under a photon flux of 3.75 Mcps/mm2. The double-sided silicon-strip detector is a promising candidate for digital mammography applications.

Characterizing a Geant4 Monte Carlo model of a multileaf collimator for a TrueBeam™ linear accelerator.

PURPOSE: The purpose of this work was to develop and validate a multileaf collimator (MLC) model for a TrueBeam™ linac using Geant4 Monte Carlo (MC) simulation kit. METHODS: A Geant4 application was developed to accurately represent TrueBeam™ linac. Pre-computed phase-space file in a plane just above the jaws was used for radiation transport. A Varian 120 leaf Millennium™ MLC was modeled using geometry and material specifications provided by the manufacturer using Geant4 constructs. Leaf characteristics e.g. tongue-groove design, variable thickness, interleaf gap were simulated. The linac model was validated by comparing simulated dose profiles and depth-doses with experimental data using an ionization chamber in water. Dosimetric characteristics of the MLC such as inter- and intra-leaf leakage, penumbra effect, MLC leaf positioning, and dynamic characteristics were also investigated. RESULTS: For the depth dose curves, 99% of the calculated data points agree within 1% of the experimental values for the 4 × 4 cm2 and 10 × 10 cm2 and within 2% of the experimental values for 20 × 20, 30 × 30 and 40 × 40 cm2 jaw defined fields. The cross-plane dose profiles show agreement <2% for depths up to 10 cm and to within 4% beyond 10 cm. MLC dosimetric characterization with MC agree well with film measurements. The rounded leaf penumbra remained constant throughout the range of leaf motion. CONCLUSIONS: The TrueBeam™ linac equipped with 120-leaf MLC was successfully modeled using Geant4. The accuracy of the model was verified by comparing the simulations with experiments. The model may be utilized for independent dose verification and QA of IMRT.

Organohalide Lead Perovskites: More Stable than Glass under Gamma-Ray Radiation.

Organohalide metal perovskites have emerged as promising semiconductor materials for use as space solar cells and radiation detectors. However, there is a lack of study of their stability under operational conditions. Here a stability study of perovskite solar cells under gamma-rays and visible light simultaneously is reported. The perovskite active layers are shown to retain 96.8% of their initial power conversion efficiency under continuous irradiation of gamma-rays and light for 1535 h, where gamma-rays have an accumulated dose of 2.3 Mrad. In striking contrast, a glass substrate shows obvious loss of transmittance under the same irradiation conditions. The excellent stability of the perovskite solar cells benefits from the self-healing behavior to recover its efficiency loss from the early degradation induced by gamma-ray irradiation. Defect density characterization reveals that gamma-ray irradiation does not induce electronic trap states. These observations demonstrate the prospects of perovskite materials in applications of radiation detectors and space solar cells.

Design and numerical simulations of W-diamond transmission target for distributed x-ray sources.

Distributed x-ray sources enable novel designs of x-ray imaging systems. However, the x-ray power of such sources is limited by the focal spot power density of the fixed anode. To further improve x-ray output, we have designed and evaluated a diamond-W transmission target for multi-pixel x-ray sources. The target features a thin layer of tungsten deposited on a diamond substrate. The thickness of tungsten layer was optimized for maximum fluence through Monte Carlo simulations. Finite element thermal simulations were performed to evaluate focal spot temperature in the target under different power loadings and dwell duration. The results showed that the optimal thickness of the tungsten layer in the W-diamond transmission target is linearly proportional to the electron energy. A 5-6 µm tungsten thickness is suitable for the kVps ranges from 60 kVp to 140 kVp. A W-diamond transmission target produces up to 20% more x-ray fluence than a traditional W reflection target in the beam center depending on the kVp settings. The x-ray spectrum of the transmission target shows less characteristic x-rays than that of reflection target. The thermal performance of W-diamond targets for peak power is significantly better than that of reflection targets. The maximum focal spot power densities of W-diamond transmission and W reflection targets are both strongly dependent on the dwell duration. For longer pulse durations, the W-diamond target allows as much as a four-fold increase in power and an eight-fold increase in power density in comparison to a traditional W reflection target for the same temperature spikes. The stability of the W-diamond bond needs to be tested experimentally. Nevertheless, the W-diamond transmission target is an appealing target that can significantly simplify the design and improve the performance of distributed x-ray sources.

Development of multi-pixel x-ray source using oxide-coated cathodes.

Multiple pixel x-ray sources facilitate new designs of imaging modalities that may result in faster imaging speed, improved image quality, and more compact geometry. We are developing a high-brightness multiple-pixel thermionic emission x-ray (MPTEX) source based on oxide-coated cathodes. Oxide cathodes have high emission efficiency and, thereby, produce high emission current density at low temperature when compared to traditional tungsten filaments. Indirectly heated micro-rectangular oxide cathodes were developed using carbonates, which were converted to semiconductor oxides of barium, strontium, and calcium after activation. Each cathode produces a focal spot on an elongated fixed anode. The x-ray beam ON and OFF control is performed by source-switching electronics, which supplies bias voltage to the cathode emitters. In this paper, we report the initial performance of the oxide-coated cathodes and the MPTEX source.

Gamma-ray rejection, or detection, with gadolinium as a converter.

Gadolinium is a competent neutron conversion material for neutron detection due to its extremely high neutron capture cross section. It differs from the other neutron reactive materials by emitting large amounts of low-energy electrons for the consequent signal generation in a detector. Such low-energy electrons, though abundant, are prone to be contaminated by internal and/or external gamma rays, such as the activated 43.0 keV K-X rays, given the high atomic number of gadolinium. While the 43.0 keV K-X ray ought to be rejected as it originates in part from the external gamma rays when neutron detection is concerned, the ability to separate this energy line from other signals points to a practical mode of gamma-ray detection by a thin-film semiconductor with gadolinium as a converter. In this paper, a gamma-ray discrimination scheme for neutron detection is studied, which also provides insight into gamma-ray detection with a small semiconductor device with gadolinium as a converter, in line with the same principle of isolating the K-X rays activated by high- or medium-energy gamma rays.