Comparison of the accuracy of bracket axial positioning with and without radiographic support and according to practitioner experience: A three-dimensional study.

INTRODUCTION: Accurate bracket positioning remains challenging. To avoid angulation errors, some recommend examining the panoramic radiograph during bonding. However, it can cause distortions. Cone-beam computed tomography (CBCT) provides a more precise panoramic reconstruction but with higher radiation doses. The main objective of this study is to compare the accuracy of axial positioning between direct bonding without radiography, with conventional panoramic radiograph, and with panoramic reconstruction from CBCT. The secondary objectives are to evaluate positioning accuracy of each tooth and to assess the influence of practitioner level of experience. METHODS: Thirty practitioners, divided into two groups based on their experience performed direct bonding on a model thrice: without radiography, then with the conventional panoramic radiograph, then with the panoramic reconstruction from CBCT. Models were scanned, and angulation errors were measured using OrthoAnalyzer. Values were compared using the Friedman's test followed by the Bonferroni correction for multiple comparisons (P-value = 0.05). RESULTS: For the low level of experience group, angulation errors were significantly greater than the accepted limit without radiographic reference, and significantly lower with CBCT reconstruction. For the high level of experience group, angulation errors were significantly lower than the accepted limit for the three bonding methods. For every tooth, using the panoramic reconstruction from CBCT as a reference, was the most accurate method, regardless of the level of experience. More experienced practitioners made fewer errors for the three methods. CONCLUSIONS: Panoramic reconstruction from CBCT is the most accurate method to limit angulation errors during direct bonding. Conventional panoramic radiography remains a reliable tool if used with caution. Bonding without any radiographic reference should be avoided especially for less experienced practitioners.

Effect of power arm length combined with additional anterior torque on the axial orientation of the maxillary incisors during en-masse retraction: A finite element analysis.

INTRODUCTION: This study aimed to clarify the effect of power arm length combined with additional torque incorporated into the archwire on the controlled movement of the anterior teeth using the finite element method. METHODS: An adult patient requiring medium anchorage after extraction of the maxillary first premolars was selected for this study. The power arms were placed between the lateral incisor and the canine at 3 levels: 3 mm, 6 mm, and 9 mm. A 150 g of retraction force was applied from each height of the anterior hook to the first molar tube, with 0°, 5°, and 10° of applied lingual root torque on the incisors. RESULTS: A 3-mm hook with 10° of applied torque, a 6-mm hook with 5° of applied torque, or a 9-mm hook with no extra torque constituted the best combinations targeted at controlling the inclination of incisors during retraction. Extrusion and distal tipping of the canine were observed. Moreover, mesial tipping and mesiopalatal rotation of the molar were unavoidable. Finally, intercanine and intermolar widths were decreased. CONCLUSIONS: Adding extra torque on the incisors or using high torque brackets is recommended for patients with maxillary first premolar extraction.

Influence of orthodontic bracket prescription on smile attractiveness in patients with different sagittal skeletal patterns: A 3-dimensional cross-sectional study.

INTRODUCTION: The objective of this study was to evaluate the influence of orthodontic bracket prescription on smile attractiveness. METHODS: Three women were chosen according to their sagittal skeletal pattern: skeletal Class I, II, or III malocclusion. For each, 3 smiling pictures were taken in frontal, oblique, and lateral views. The maxillary arch was then scanned, and a 3-dimensional digital model was constructed on the OrthoAnalyzer software. The information of 3 orthodontic prescriptions, namely Roth, MBT, and Ricketts, was simulated after the virtual placement of orthodontic brackets on 10 maxillary teeth. The simulations were then superimposed on the smile photographs in the 3 views, creating a total of 27 images. Groups of orthodontists, dentists, and laypeople rated the attractiveness of each smile using the visual analog scale. RESULTS: This study included 167 evaluators: 54 orthodontists, 54 dentists, and 59 laypersons. In terms of orthodontic prescription, MBT esthetic scores were 4% lower than Roth scores (P <0.001), and Ricketts scores were 13.6% lower than Roth scores (P <0.001). In terms of skeletal pattern, Class II and III scores were 15.0% and 16.4% lower than Class I scores, respectively (P <0.001). Regarding the smiling view, oblique view scores were 3.1% lower than frontal view scores (P = 0.031), whereas lateral view scores were 8.4% lower than frontal view scores (P <0.001). In contrast to gender and age, the specialty of the evaluators significantly affected the esthetic rating of the smiles. CONCLUSIONS: The attractiveness of a smile is affected by the prescription of the brackets. The Roth prescription tends to obtain the most favorable esthetic scores, especially in sagittal smiling images. Profile smiles with excessively proclined incisors are considered unattractive. Different views of the same smile do not get similar esthetic scores because sagittal views are rated the most severely.

Three-dimensional comparison of continuous and segmented arch techniques in the traction of palatally impacted canines using a non-linear finite element analysis.

OBJECTIVE: To compare the three-dimensional (3D) effects of canine traction on the maxillary teeth when using two different traction methods, the continuous and the segmented arch wire techniques; then to test whether adding a transpalatal arch (TPA) would affect their response to traction. DESIGN: Finite element analysis. METHODS: A cone-beam computed tomography (CBCT) scan of a patient with bilateral palatally impacted canines was chosen, from which a 3D model was derived and imported into ABAQUS. Two arch wires were modelled, a continuous round one and a segmented rectangular one. Four models were obtained by adding a TPA to both techniques. A 100° imposed rotation was then applied at the intersection between the vertical loop and the horizontal segment of each wire. Initial displacement of the maxillary tooth in the labio-lingual and in the vertical directions was measured. The absolute maximum principal stress of the periodontal ligament (PDL) was also assessed. RESULTS: Traction using a continuous arch wire led to different movement patterns of all teeth, some of them were tipped in a labial direction while others were lingually tipped. Traction using a segmented arch wire resulted in a retroclination of the posterior teeth and a proclination of the anterior teeth with a high level of stress on the premolars' PDL. Adding the TPA only affected the displacement of the first molars. The right side showed a maximum displacement of the first premolar, while the left side showed it on the lateral. The total displacement on the right side was higher than the left side. CONCLUSION: The segmented technique caused a uniform displacement of all teeth while the continuous one showed a non-uniform displacement. The angulation and position of the vertical loop affected the displacement of the maxillary teeth. The addition of a TPA acted only on the first molars.

Factors influencing the perception of profile beauty in Class III dental compensation: A comparative cross-sectional study according to three categories of assessors.

INTRODUCTION: The main objective of this study was to evaluate the different factors influencing the perception of female profile facial beauty in Class III patients with protruded mandible that can be treated with orthodontic dental compensation: (1)severity of the protrusion, (2) the upper incisors inclination and (3) the presence of jawlines. The secondary objective was to determine if the rater's gender and profession played a role in the assessment of the preferred profile. METHODS: A normal and smiling photographs of a female subject with normal facial and skeletal profile criteria were digitally manipulated to obtain 3 different mandibular sagittal positions: 0mm, +4mm and +8mm. Each position of the chin was evaluated with the presence or not of jawlines. In the smiling profiles, the same chin modifications were scored, and the maxillary incisor inclination was changed from 0 to +10 degrees with 5 degrees increments. A total of 320 raters (107 dentists, 103 orthodontists and 110 laypeople) scored the attractiveness of the different images using a Visual Analogue Scale. The limit of statistical significance was P<0.05. Generalized estimating equation (GEE) models were conducted to assess the predictors of variations in ratings within each set of photos, as well as the interactions of predictors where adjusted odds ratios (aOR) and their 95% confidence intervals were calculated and reported. RESULTS: In the profiles without a smile, image +4mm chin (Class III treated by compensation) and image +8-mm mandible (Class III not treated) were selected as the most and least attractive images, respectively, by almost all groups with no difference. The presence of jawlines has a positive role in facial attractiveness. In the smiling profiles, all the examiners showed a preference for image +4-mm chin and a slight protrusion of maxillary incisors (+5 degrees). No significant difference was found between genders in this study. CONCLUSIONS: Class III treated by compensation (+4mm) are more attractive than non-treated Class III (+8mm) by almost all groups with no difference. The presence of jawlines has a positive role in facial attractiveness. In the smiling profiles, all the examiners showed a preference for image +4-mm chin and a slight protrusion of maxillary incisors (+5 degrees). Orthodontists older than 50 years old are aware of the difficulty to treat a skeletal Class III and tend to accept it due to their long career experience. No significant difference was found between genders in this study.

In-vivo durability of Pro Seal in patients with fixed orthodontic appliances: A controlled clinical trial.

BACKGROUND: This clinical trial aimed at studying the durability of an orthodontic sealant (Pro Seal) used on tooth surfaces for protection against white spot lesions. METHODS: A total of 35 patients (18 females, 17 males; 17.57 ± 1.36 years) were recruited. Eligibility criteria included healthy patients of both sexes (age > 14 years), absence of labial caries, absence of defective enamel, absence of extensive restorations, and optimum oral hygiene. The participants received a single application of Pro Seal on the bonded teeth. The sealant covered the labial enamel surrounding the brackets. Participants were recalled monthly after sealant application, during which sealant layers were evaluated using an ultraviolet lamp. The assessment was realized using an index similar to the adhesive remnant index (ARI). RESULTS: A total of 30 participants completed the trial. ARI values dropped significantly (P < 0.001) and reached <1.5 at T1 on the index used. An ARI value of 2 was chosen as the threshold below which a tooth presented an insufficient sealant layer. The right and left sides of both jaws did not show any statistically significant difference (P > 0.05). ARI values of homolateral teeth revealed few statistically significant differences between upper and lower teeth. No statistically significant difference between the two sexes (P > 0.05) existed. No harm or disturbance was reported by any of the participants. CONCLUSIONS: This study demonstrated that a single application of Pro Seal is effective for 4 weeks and should be renewed monthly. No interjaw, intrajaw, or intersex significant differences were found.

Effects of enamel deproteinization with different application times on the shear bond strength of a self-etching primer: An in vitro study.

OBJECTIVE: The aim of this in vitro study was to evaluate the effects of enamel deproteinization on the shear bond strength of a self-etching primer Transbond Plus™(TBP), with different application times of sodium hypochlorite (NaOCl 5.25%), primarily and secondarily on the adhesive remnant index score. MATERIALS AND METHODS: One hundred twenty-five freshly extracted human premolars were randomly and blindly divided into five groups according to the enamel surface preparation, as follows (n=25): group 1(control): Etching with 37% phosphoric acid for 15seconds+Bonding; group 2 (control): TBP™ without NaOCl, group 3: 60seconds NaOCl+TBP™, group 4: 30seconds NaOCl+TBP™, group 5: 15seconds NaOCl+TBP™. The same composite resin was used (Transbond XT™) to bond the orthodontic metal brackets. After the immersion of the teeth in distilled water at 37°C for 24hours the shear bond strength was measured using the universal testing machine and the adhesive remnant index score (ARI) was evaluated under an optical microscope (25×). RESULTS: The mean SBS values (inMPa) of the groups were respectively: group 1: 13.03±5.36; group 2: 12.28±3.06; group 3: 12.38±4.55; group 4: 12.98±5.76; and group 5: 11.73±5.67. Enamel deproteinization increased the SBS for groups 3 and 4, but no statistically significant difference was found between the five groups (P=0.883). Group 1 showed the highest ARI scores, with 52% of the teeth retaining all the adhesive (score 3). However, for all the other groups, scores 0 and 1 were predominant, with less than half of the adhesive or no adhesive at all remaining on the teeth. CONCLUSIONS: Enamel deproteinization with sodium hypochlorite (5.25%) and the variation of its application time has no effect on the SBS of the self-etching primer Transbond Plus ™.

Evaluation of the distance between the root apices of the upper first molars and the hard palate in an Eastern Mediterranean population: A retrospective study.

OBJECTIVE: The aims of this retrospective study were, first to evaluate the distance between the root apices of the upper first molars and the palatal plane (PP), and second to determine the validity (accuracy) of the use of cephalometric radiographs or panoramic X-rays compared to cone beam computed tomography (CBCT) in determining this distance. MATERIAL AND METHODS: The distance was calculated from the root apices of the first molars to PP, on the cephalometric radiographs of 204 subjects and then 57 measurements were compared to those obtained on panoramic X-rays and CBCT images, in order to find a statistically significant difference according to age, sex, side, vertical and sagittal skeletal patterns, and to determine if 2D radiographs are suitable for this task. RESULTS: The distance increased significantly in subjects after 20 years of age and in hyperdivergent patients, but was not influenced by sex, side or anteroposterior position of the mandible. No statistical significance was found between the calculated measurements on cephalometric and CBCT radiographs, but both were different from those taken on panoramic X-rays. CONCLUSIONS: Cephalometric radiographs are reliable in the assessment of the distance between the roots of the upper molars and the PP. In hyperdivergent and adult patients, posterior teeth have enough space between their roots and the upper limit of the hard palate to undergo intrusion mechanics using miniscrews, but care must be taken while planning and managing these movements in order to minimize the unwanted side effects.

[Impact of orthodontic treatment and psychological parameters on oral health related quality of life of children in Middle Eastern country]. / Impact du traitement orthodontique et des paramètres psychologiques sur la qualité de vie liée à la santé orale chez les enfants au Moyen-Orient.

This study is aimed at evaluating the Oral Health Related Quality of Life (OHRQoL) in adolescents aged 11-14 years-old during orthodontic therapy and 18 months after the start of treatment and the possible role of psychological parameters. Sixty patients were recruited, and data were collected using self-administrated questionnaires and intraoral clinical examinations. The questionnaires included sociodemographic characteristics (age, gender), the Lebanese version of the Child Perception Questionnaire between 11 and 14 years CPQ11-14 to assess the OHRQoL, the Discrepancy Aesthetic Index (DAI) for malocclusion, and the Child Health Questionnaire « CHQ-CF87 ¼ to appraise Self-Esteem (SE) and Psychological Well-Being (PWB). The mean scores of CPQ11-14 and its four subdomains were significantly better for participants with high SE /PWB compared to those with low SE / PWB at baseline. These same scores improved significantly during orthodontic treatment (p < 0.001). However, DAI was significantly better in patients with low self-esteem and psychological well-being. Our findings showed improvement in oral health perception and psychologic parameters during orthodontic treatment. Investigators should consider the need to control the psychological parameters of patients when assessing orthodontic treatment need and improvement in OHRQoL during orthodontic treatment.

Correlation between fusion of spheno-occipital synchondrosis and cervical vertebral maturation: A CBCT and cephalometric assessment.

OBJECTIVE: The aim of this study was to determine among young orthodontic patients the relation between the spheno-occipital synchondrosis (SOS) fusion and the cervical vertebral maturation (CVM) and to look for an eventual impact of gender, skeletal class and vertical pattern on their association. MATERIAL AND METHODS: CBCT scans and lateral cephalometric radiographs of 117 patients, aged between 8 and 18 years, were selected. SOS fusion was assessed on a mid-sagittal cut of the CBCT scans. CVM was evaluated on the lateral cephalograms as well as ANB and GoGn-SN angles. Spearman correlation test was used to assess the relationship between SOS and CVM. Fisher's exact test was performed at every CVM stage to analyse the association between SOS and other variables (gender, skeletal class, and vertical pattern). Cohen's kappa analysis was used for reliability. RESULTS: A strong correlation was found between SOS maturation and CVM (r=0.852, P<001). Fisher's exact test indicated significant association only between gender and SOS in CVM stage 2 group, and between vertical pattern and SOS in CVM stage 4. Cohen's kappa analysis showed moderate inter and intra-rater reliability for CVM index (k=0.50 and 0.53 respectively, P<.001), strong inter-rater reliability (k=0.80, P<.001) and almost perfect intra-rater reliability (k=0.85, P<.001) for SOS index. CONCLUSIONS: SOS fusion correlates well with CVM and might be a reliable tool for skeletal maturation assessment. Girls seem to have an earlier fusion of SOS in relation to their respective CVM compared to boys, and the vertical pattern could influence the association between SOS and CVM stages.

[Facial profile preferences: a cross-sectional survey]. / Evaluation esthétique du profil cutané : une étude transversale.

INTRODUCTION: The aim of this study is to identify facial profile preferences among Lebanese orthodontists, general dentists and laypersons. MATERIALS AND METHODS: A lateral photograph of a young man and young woman with a class I skeletal relationship was used. Each photograph was manipulated, using Dolphin Imaging System®, to produce six other photographs in which anteroposterior variations in the position of the maxilla and/or the mandible were made. A total of 120 participants were asked to rank the photographs of each gender from most to least attractive. RESULTS: The straight profile was the most favored in men and women; however more lip protrusion for women and maxillary retrusion for men are tolerated. DISCUSSION: Our results represent the mean evaluation of a Caucasian society, this does not mean that every straight profile will be perceived as an attractive one. Hence the importance of an individualized treatment planning for a successful orthodontic treatment.