A biophotoelectrode based on boronic acid-modified Chlorella vulgaris cells integrated within a redox polymer.

Green microalgae are gaining attention in the renewable energy field due to their ability to convert light into energy in biophotovoltaic (BPV) cells. The poor exogenous electron transfer kinetics of such microorganisms requires the use of redox mediators to improve the performance of related biodevices. Redox polymers are advantageous in the development of subcellular-based BPV devices by providing an improved electron transfer while simultaneously serving as immobilization matrix. However, these surface-confined redox mediators have been rarely used in microorganism-based BPVs. Since electron transfer relies on the proximity between cells and the redox centres at the polymer matrix, the development of molecularly tailored surfaces is of great significance to fabricate more efficient BPV cells. We propose a bioanode integrating Chlorella vulgaris embedded in an Os complex-modified redox polymer. Chlorella vulgaris cells are functionalized with 3-aminophenylboronic acid that exhibits high affinity to saccharides in the cell wall as a basis for an improved integration with the redox polymer. Maximum photocurrents of (5 ± 1) µA cm-2 are achieved. The developed bioanode is further coupled to a bilirubin oxidase-based biocathode for a proof-of-concept BPV cell. The obtained results encourage the optimization of electron-transfer pathways toward the development of advanced microalgae-based biophotovoltaic devices.

Combination of ferrocene decorated gold nanoparticles and engineered primers for the direct reagentless determination of isothermally amplified DNA.

A reagent-less DNA sensor has been developed exploiting a combination of gold nanoparticles, modified primers, and isothermal amplification. It is applied to the determination ofKarlodinium armiger, a toxic microalgae, as a model analyte to demonstrate this generic platform. Colloidal gold nanoparticles with an average diameter of 14 ± 0.87 nm were modified with a mixed self-assembled monolayer of thiolated 33-mer DNA probes and (6-mercaptohexyl) ferrocene. Modified primers, exploiting a C3 spacer between the primer-binding site and an engineered single-stranded tail, were used in an isothermal recombinase polymerase amplification reaction to produce an amplicon by two single-stranded tails. These tails were designed to be complementary to a gold electrode tethered capture oligo probe, and an oligo probe immobilized on the gold nanoparticles, respectively. The time required for hybridization of the target tailed DNA with the surface immobilized probe and reporter probe immobilized on AuNPs was optimized and reduced to 10 min, in both cases. Amplification time was further optimized to be 40 min to ensure the maximum signal. Under optimal conditions, the limit of detection was found to be 1.6 fM of target dsDNA. Finally, the developed biosensor was successfully applied to the detection of genomic DNA extracted from a seawater sample that had been spiked with K. armiger cells. The demonstrated generic electrochemical genosensor can be exploited for the detection of any DNA sequence and ongoing work is moving towards an integrated system for use at the point-of-need.

Direct electrochemical detection of enzyme labelled, isothermally amplified DNA.

Genosensors for the detection of DNA via hybridisation normally require post-amplification processing such as the generation of single-stranded DNA and pre-detection labelling, complicating and lengthening the assay. A straightforward electrochemical genosensor, for the direct detection of isothermally generated nucleic acid amplicons via hybridisation is reported. The detection of Karlodinium armiger, responsible for harmful algae blooms was used as a model system to demonstrate the proof of concept. The approach exploits the use of specifically modified primers designed to generate amplicons with a central duplex flanked by a single-stranded tail at one end of the duplex and a horse-radish peroxidase on the other end. Individual gold electrodes of an array were functionalised with self-assembled monolayers of short thiolated DNA probes, designed to hybridise with the single-stranded tailed amplicon with the reporter enzyme label incorporated. The optimum amplification time was determined to be 60 min, at a fixed temperature of 37 °C. The hybridisation time to the enzyme labelled amplicon was optimised to be 10 min, but 2 min hybridisation time was also adequate. In this first example of using horse radish peroxidase-labelled primer in solution-phase recombinase polymerase amplification for subsequent detection via solid-phase hybridisation, the detection limit achieved was 0.4 fM, equivalent to 27622 cells/L, and the developed genosensor was applied to the detection of synthetic as well as genomic DNA, which had been extracted from a seawater sample.

Colorimetric DNA-based assay for the specific detection and quantification of Ostreopsis cf. ovata and Ostreopsis cf. siamensis in the marine environment.

Ostreopsis is a toxic benthic dinoflagellate largely distributed worldwide in tropical and temperate areas. In the Mediterranean Sea, periodic summer blooms have been reported and have become a serious concern due to their direct impact on human health and the environment. Current microalgae identification is performed via light microscopy, which is time-consuming and is not able to differentiate among Ostreopsis species. Therefore, there is mature need for rapid, specific and easy-to-use detection tools. In this work, a colorimetric assay exploiting a combination of recombinase polymerase amplification (RPA) and a sandwich hybridisation assay was developed for O. cf. ovata and O. cf. siamensis detection and quantification. The specificity of the system was demonstrated by cross-reactivity experiments and calibration curves were successfully constructed using genomic DNA, achieving limits of detection of 10 and 14 pg/µL for O. cf. ovata and O. cf. siamensis, respectively. The assay was applied to the analysis of planktonic and benthic environmental samples from different sites of the Catalan coast. Species-specific DNA quantifications were in agreement with qPCR analysis, demonstrating the reliability of the colorimetric approach. Significant correlations were also obtained between DNA quantifications and light microscopy counts. The approach may be a valuable tool to provide timely warnings, facilitate monitoring activities or study population dynamics, and paves the way towards the development of in situ tools for the monitoring of harmful algal blooms.

Electrochemical genosensor for the direct detection of tailed PCR amplicons incorporating ferrocene labelled dATP.

An electrochemical genosensor for the detection and quantification of Karlodinium armiger is presented. The genosensor exploits tailed primers and ferrocene labelled dATP analogue to produce PCR products that can be directly hybridised on a gold electrode array and quantitatively measured using square wave voltammetry. Tailed primers consist of a sequence specific for the target, followed by a carbon spacer and a sequence specifically designed not to bind to genomic DNA, resulting in a duplex flanked by single stranded binding primers. The incorporation of the 7-(ferrocenylethynyl)-7-deaza-2'-deoxyadenosine triphosphate was optimised in terms of a compromise between maximum PCR efficiency and the limit of detection and sensitivity attainable using electrochemical detection via hybridisation of the tailed, ferrocene labelled PCR product. A limit of detection of 277aM with a linear range from 315aM to 10 fM starting DNA concentration and a sensitivity of 122 nA decade-1 was achieved. The system was successfully applied to the detection of genomic DNA in real seawater samples.

Detection and quantification of the toxic marine microalgae Karlodinium veneficum and Karlodinium armiger using recombinase polymerase amplification and enzyme-linked oligonucleotide assay.

Karlodinium is a dinoflagellate responsible for fish-killing events worldwide. In Alfacs Bay (NW Mediterranean Sea), the presence of two Karlodinium species (K. veneficum and K. armiger) with different toxicities has been reported. This work presents a method that combines recombinase polymerase amplification (RPA) with an enzyme-linked oligonucleotide assay (ELONA) to identify, discriminate and quantify these two species. The system was characterised using synthetic DNA and genomic DNA, and the specificity was confirmed by cross-reactivity experiments. Calibration curves were constructed using 10-fold dilutions of cultured cells, attaining a limit of detection of around 50,000 cells/L, far below the Karlodinium spp. alert threshold (200,000 cells/L). Finally, the assay was applied to spiked seawater samples, showing an excellent correlation with the spiking levels and light microscopy counts. This approach is more rapid, specific and user-friendly than traditional microscopy techniques, and shows great promise for the surveillance and management of harmful algal blooms.

Isothermal amplification using modified primers for rapid electrochemical analysis of coeliac disease associated DQB1*02 HLA allele.

DNA biosensors are attractive tools for genetic analysis as there is an increasing need for rapid and low-cost DNA analysis, primarily driven by applications in personalized pharmacogenomics, clinical diagnostics, rapid pathogen detection, food traceability and forensics. A rapid electrochemical genosensor detection methodology exploiting a combination of modified primers for solution-phase isothermal amplification, followed by rapid detection via hybridization on gold electrodes is reported. Modified reverse primers, exploiting a C18 spacer between the primer-binding site and an engineered single stranded tail, are used in a recombinase polymerase amplification reaction to produce an amplicon with a central duplex flanked by two single stranded tails. These tails are designed to be complementary to a gold electrode tethered capture oligo probe as well as a horseradish peroxidase labelled reporter oligo probe. The time required for hybridization of the isothermally generated amplicons with each of the immobilized and reporter probes was optimised to be 2 min, in both cases. The effect of amplification time and the limit of detection were evaluated using these hybridization times for both single stranded and double stranded DNA templates. The best detection limit of 70 fM for a ssDNA template was achieved using 45 min amplification, whilst for a dsDNA template, just 30 min amplification resulted in a slightly lower detection limit of 14 fM, whilst both 20 and 45 min amplification times were observed to provide detection limits of 71 and 72 fM, respectively, but 30 and 45 min amplification resulted in a much higher signal and sensitivity. The genosensor was applied to genomic DNA and real patient and control blood samples for detection of the coeliac disease associated DQB1*02 HLA allele, as a model system, demonstrating the possibility to carry out molecular diagnostics, combining amplification and detection in a rapid and facile manner.

Multiplexed isothermal nucleic acid amplification.

Multiplexed isothermal amplification and detection of nucleic acid sequences and biomarkers is of increasing importance in diverse areas including advanced diagnostics, food quality control and environmental monitoring. Whilst there are several very elegant isothermal amplification approaches, multiplexed amplification remains a challenge, requiring careful experimental design and optimisation, from judicious primer design in order to avoid the formation of primer dimers and non-specific amplification, applied temperature as well as the ratio and concentration of primers. In this review, we describe the various approaches that have been reported to date for multiplexed isothermal amplification, for both "one-pot" multiplexing as well as parallelised multiplexing using loop-mediated isothermal amplification, strand-displacement amplification, helicase-dependent amplification, rolling circle amplification, nucleic acid sequence-based amplification, with a particular focus on recombinase polymerase amplification.

Disulfide-modified antigen for detection of celiac disease-associated anti-tissue transglutaminase autoantibodies.

A simple and rapid immunosensor for the determination of the celiac disease-related antibody, anti-tissue transglutaminase, was investigated. The antigenic protein tissue transglutaminase was chemically modified, introducing disulfide groups through different moieties of the molecule (amine, carboxylic, and hydroxyl groups), self-assembled on gold surfaces, and used for the detection of IgA and IgG autoantibodies. The modified proteins were evaluated using enzyme-linked immunosorbent assay and surface plasmon resonance, which showed that only introduction of the disulfide groups through amine moieties in the tissue transglutaminase preserved its antigenic properties. The disulfide-modified antigen was co-immobilized via chemisorption with a poly(ethylene glycol) alkanethiol on gold electrodes. The modified electrodes were then exposed to IgA anti-tissue transglutaminase antibodies and subsequently to horseradish peroxidase-labeled anti-idiotypic antibodies, achieving a detection limit of 260 ng ml-1. Immunosensor performance in the presence of complex matrixes, including clinically relevant serum reference solutions and real patient samples, was evaluated. The introduction of disulfides in the antigenic protein enabled a simple and convenient one-step surface immobilization procedure involving only spontaneous gold-thiol covalent binding. Complete amperometric assay time was 30 min.

Enhanced solid-phase recombinase polymerase amplification and electrochemical detection.

Recombinase polymerase amplification (RPA) is an elegant method for the rapid, isothermal amplification of nucleic acids. Here, we elucidate the optimal surface chemistry for rapid and efficient solid-phase RPA, which was fine-tuned in order to obtain a maximum signal-to-noise ratio, defining the optimal DNA probe density, probe-to-lateral spacer ratio (1:0, 1:1, 1:10 and 1:100) and length of a vertical spacer of the probe as well as investigating the effect of different types of lateral spacers. The use of different labelling strategies was also examined in order to reduce the number of steps required for the analysis, using biotin or horseradish peroxidase-labelled reverse primers. Optimisation of the amplification temperature used and the use of surface blocking agents were also pursued. The combination of these changes facilitated a significantly more rapid amplification and detection protocol, with a lowered limit of detection (LOD) of 1 · 10-15 M. The optimised protocol was applied to the detection of Francisella tularensis in real samples from hares and a clear correlation with PCR and qPCR results observed and the solid-phase RPA demonstrated to be capable of detecting 500 fM target DNA in real samples. Graphical abstract Relative size of thiolated lateral spacers tested versus the primer and the uvsx recombinase protein.

Isothermal solid-phase amplification system for detection of Yersinia pestis.

DNA amplification is required for most molecular diagnostic applications, but conventional polymerase chain reaction (PCR) has disadvantages for field testing. Isothermal amplification techniques are being developed to respond to this problem. One of them is the recombinase polymerase amplification (RPA) that operates at isothermal conditions without sacrificing specificity and sensitivity in easy-to-use formats. In this work, RPA was used for the optical detection of solid-phase amplification of the potential biowarfare agent Yersinia pestis. Thiolated forward primers were immobilized on the surface of maleimide-activated microtitre plates for the quantitative detection of synthetic and genomic DNA, with elongation occurring only in the presence of the specific template DNA and solution phase reverse primers. Quantitative detection was achieved via the use of biotinylated reverse primers and post-amplification addition of streptavidin-HRP conjugate. The overall time of amplification and detection was less than 1 h at a constant temperature of 37 °C. Single-stranded DNA (ssDNA) and double-stranded DNA (dsDNA) sequences were detected, achieving detection limits of 4.04*10(-13) and 3.14*10(-16) M, respectively. The system demonstrated high specificity with negligible responses to non-specific targets.

Modified primers for rapid and direct electrochemical analysis of coeliac disease associated HLA alleles.

Direct detection of PCR product via hybridisation assay, would facilitate the development of rapid tools for genetic analysis. Here, a PCR primer designed to generate a PCR amplicon tagged with single stranded DNA tails at each end of the duplex, which can be used for direct hybridisation with a surface immobilised probe and an enzyme labelled reporter probe is presented. Four modified sequence specific primers (SSP) pairs were designed for the selective amplification of coeliac disease associated alleles (DQA1*05, DQB1*02, DQB1*03:02 alleles), and human growth hormone (positive control). Multiplex PCR products were electrochemically detected in less than 5 min at 37 °C via direct hybridisation to short probes immobilised on individual electrodes of a genosensor array, and subsequent hybridisation to an enzyme labelled reporter probe. The developed electrochemical genosensor array exploiting the modified primers for the direct detection of PCR products was applied to the genotyping of real patient samples.

Bleed-to-read disposable microsystems for the genetic and serological analysis of celiac disease markers with amperometric detection.

Celiac disease is an auto-immune disorder induced by ingestion of gluten in genetically predisposed individuals. Its diagnostics is more accurate using a combination of immunologic and genetic tests to detect of high levels of certain auto-antibodies and the presence human leukocyte antigen HLA-DQ2 or HLA-DQ8 genetic markers. In this work, we report the design and testing of automated microsystems combining sample treatment, storage, fluidic transport, and detection in a single platform able to carry out genetic or serologic analysis for detection of celiac disease markers. These microsystems share a common footprint and many fluidic features and are thus able to perform a complete assay. The microsystem for the genetic assay extracts and amplifies the DNA prior to detection, while the serology microsystem contains a filter and chamber for the generation and subsequent dilution of plasma. The performance of both platforms is demonstrated and compared with reference methods with an excellent correlation, which makes the developed platform amenable for clinical studies.

DNA biosensor based on hybridization refractory mutation system approach for single mismatch detection.

We report on a simple approach to enhance solid-phase hybridization-based single base mismatch discrimination at high ionic strength based on the deliberate insertion of a natural DNA base mismatch in the surface-tethered probe. A large drop in hybridization signal of single base mismatched alleles using the designed probe as compared with the conventional probe, from 80% to less than 25% of the signal obtained with the fully complementary, non-mutation-containing sequence, when using colorimetric detection was further improved to 20% when using electrochemical detection, attributable to a difference of spacing of immobilized probes. Finally, the designed probe was used for the electrochemical detection of the DQA1*05:05 allele amplified from real human blood samples.

Medium-high resolution electrochemical genotyping of HLA-DQ2/DQ8 for detection of predisposition to coeliac disease.

Coeliac disease is a small intestinal disorder, induced by ingestion of gluten in genetically predisposed individuals. Coeliac disease has been strongly linked to human leukocyte antigens (HLA) located on chromosome 6, with almost 100 % of coeliac disease sufferers carrying either a HLA-DQ2 or HLA-DQ8 heterodimer, with the majority carrying HLA-DQ2 encoded by the DQA1*05:01/05:05, DQB1*02:01/02:02 alleles, whereas the remaining carry the HLA-DQ8 encoded by the DQA1*03:01, DQB1*03:02 alleles. In this work, we present the development of a multiplex electrochemical genosensor array of 36 electrodes, housed within a dedicated microfluidic platform and using a total of 10 sequence-specific probes for rapid medium-high resolution HLA-DQ2/DQ8 genotyping. An evaluation of the selectivity of the designed probes was carried out with the target sequences and 44 potentially interfering alleles, including single base mismatch differentiations; good selectivity was demonstrated. The performance of the electrochemical genosensor array was validated, analyzing real human samples for the presence of HLA-DQ2/DQ8 alleles, and compared with those obtained using laboratory-based HLA typing, and an excellent correlation was obtained.

Eletrochemically actuated stop-go valves for capillary force-operated diagnostic microsystems.

Lateral-flow immunosensing devices continue to be the most successful commercial realization of analytical microdevices. They owe their success to their simplicity, which significantly depends on the capillary-driven flow and versatile technological platform that lends itself to fast and low-cost product development. To compete with such a convenient product, microsystems can benefit from simple-to-operate fluid manipulation. We show that the capillary-driven flow in microchannels can be manipulated with electrochemically activated valves with no moving parts. These valves consist of screen-printed electrode pairs that are transversal to the flow. One of the electrodes is solvent-etched to produce a superhydrophobic surface that provides passive stopping and facilitates low-voltage (~1 V) actuation of the flow via electrowetting. The operation of such valves in the stop-go mode, with a response time between 2 and 45 sec depending on the type and concentration of salt, is demonstrated. Mechanistic investigations indicated that the response depends on at least three phenomena that contribute to electrocapillarity: the electrochemical double-layer capacitance, specific counterion adsorption, and possible electrohydrodynamic effects.

Antibodies to wheat high-molecular-weight glutenin subunits in patients with celiac disease.

BACKGROUND: Wheat gluten comprises gliadins and glutenins. The high-molecular-weight (HMW) glutenin subunits (GS)-1Dy10 are toxic for patients with celiac disease (CD). This study aimed to assess whether CD patients mount a serological response to HMW-GS-1Dy10. METHODS: Recombinant HMW-GS-1Dy10 was deamidated using human recombinant tissue transglutaminase. MALDI-TOF was performed to compare the level of deamidation of glutamine residues between material before and after treatment. Enzyme-linked immunosorbent assays were developed. Sera from patients with untreated CD and gastrointestinal disease controls were tested and receiver operator characteristics were used to calculate cutoffs. RESULTS: MALDI-TOF revealed a number of fragments matching known HMW-GS-1Dy10 sequences within both the deamidated and non-deamidated material. Evidence of deamidation of glutamine residues was found only within the human transglutaminase-treated material. Patients with untreated CD had significantly increased levels of serum antibodies to HMW-GS-1Dy10 compared to controls. Undeamidated HMW-GS-1Dy10 IgA antibodies had sensitivities and specificities of 72.5 and 78.26%, respectively. Deamidated HMW-GS-1Dy10 IgA antibodies had sensitivities and specificities of 76.8 and 65.2%. Undeamidated HMW-GS-1Dy10 IgG antibodies had sensitivities and specificities of 75.3 and 68.1%. Deamidated HMW-GS-1Dy10 IgG antibodies had sensitivities and specificities of 36.2 and 92.8%. CONCLUSION: Patients with untreated CD have raised antibody levels to HMW-GS-1Dy10, indicating the participation of these proteins in the adaptive immune response to gluten. Discrimination between CD patients and controls is not enhanced by deamidation of HMW-GS-1Dy10. Thus antibodies to these proteins are not useful markers for CD detection.

Low-medium resolution HLA-DQ2/DQ8 typing for coeliac disease predisposition analysis by colorimetric assay.

Coeliac disease is an inflammation of the small intestine, occurring in genetically susceptible individuals triggered by the ingestion of gluten. Human Leukocyte Antigens (HLA) DQ2 and DQ8 gene have been identified as key genetic factors in coeliac disease as they are presented in almost 100 % of the patients. These genes are encoded by the combination of certain alleles in the DQA and DQB region of chromosome 6. Specifically, DQA1*05:01 and DQB1*02:01 alleles for serologically defined leukocyte antigen DQ2 cis, DQA1*05:05 and DQB1*02:02 for DQ2 trans and DQA1*03:01 and DQB1*03:02 alleles for the DQ8. Specific identification of these alleles is a challenge due to the high number of alleles that have been identified so far: 46 in the DQA region and 160 in the DQB region (as of IMGT/HLA Database 10/2011 release). In the reported work, the development of a multiplex colorimetric assay for the low to medium HLA typing of the DQ2 and DQ8 genes is presented. The optimisation of probe design and assay conditions, performed by both surface plasmon resonance and enzyme-linked oligonucleotide assay, are reported. Finally, the performances of the developed typing platform were validated by the analysis of real patient samples and HLA typing, compared with those obtained using hospital based typing technology and an excellent correlation obtained.

Amperometric immunosensor for the determination of IgA deficiency in human serum samples.

An electrochemical immunosensor for the detection of human IgA deficiency in real human blood serum has been developed. The performance of the immunosensor presents a large but sensitive dynamic range that allows the determination of non-deficient IgA levels (>70 µg/mL) as well as of severe IgA deficiencies (0.5-5.0 µg/mL). The assay architecture involves the immobilisation of a coating antibody on an electrode surface using carboxylic-ended bipodal alkane-thiol self-assembled monolayers (SAMs). The long chain bipodal SAM presents intercalated poly(ethylenglycol) groups that confer the immunosensor the ability to retain its optimum performance in very complex matrices and serum with negligible non-specific adsorption phenomena. Amperometric optimisation of the assay resulted in limits of detection of 142 ng/mL in just 30 min total assay time. Real patients' serum samples were analysed using the developed electrochemical immunosensor demonstrating an excellent correlation in terms of sensitivity and reproducibility compared with standard enzyme linked immunosorbent assays (ELISA).