Disinfection of 3D-printed surgical guides using virgin coconut oil (in vitro study).

BACKGROUND/OBJECTIVE: Disinfection of a 3D-printed surgical guide is of utmost importance as it comes into contact with hard and soft tissue during implant placement so it poses a potential risk of pathogenic transmission. Methods used for disinfection in the surgical field should be reliable, practical, and safe for the instruments and the patients. The objectives of this study were to compare the antimicrobial potential of 100% Virgin Coconut Oil, 2% Glutaraldehyde, and 70% Ethyl Alcohol used to decontaminate 3D-printed surgical guides. MATERIALS AND METHODS: Thirty identical surgical guides were printed and cut into two halves (N = 60). Both halves were then contaminated with a defined amount of human saliva samples (2 ml). The first half (n = 30) was sub-grouped into three study groups which were immersed in one of the three disinfectants for 20 min as follows; group VCO was immersed in 100% Virgin Coconut Oil, group GA was immersed in 2% Glutaraldehyde, and group EA was immersed in 70% Ethyl Alcohol. The second half (n* = 30) was sub-grouped into three control groups which were immersed in sterile distilled water as follows group VCO*, group GA*, and group EA*. The microbial count was expressed as colony-forming units per plate and the comparison of the antimicrobial potential of the three tested disinfectants between the three study and three control groups was done using the One-Way ANOVA test. RESULTS: The culture results of three study groups revealed no bacterial growth with the highest % of reduction in the mean microbial count of the oral microorganisms (about100%) and an uncountable bacterial growth was shown between the three control groups (more than 100 CFU/plate) representing the baseline of the oral microorganisms. Therefore; statistically significant differences were found between the three control and three study groups (P < .001). CONCLUSION: The antimicrobial potential of Virgin Coconut Oil was comparable and equivalent to Glutaraldehyde and Ethyl Alcohol with a significant inhibitory action against oral pathogens.

The microbiological effect of virgin coconut oil on the morphological and volumetric dimensional changes of 3D printed surgical guides (in vitro study).

BACKGROUND/OBJECTIVES: Disinfection of surgical guides is mandatory for intraoperative use. Virgin Coconut Oil may be a potent alternative disinfectant; however, its effect has not been fully discussed in dentistry. The objectives of this study were to compare the morphological and the volumetric dimensional changes of 3D printed surgical guides after immersion in three disinfectants: 100%Virgin Coconut Oil, 2% Glutaraldehyde, and 70% Ethyl Alcohol and to assess the antimicrobial effectiveness of the tested disinfectants. MATERIALS AND METHODS: A surgical guide was designed using open platform software to print thirty guides and then cut them into two halves (N = 60). Pre-disinfection scans of the first half of the three study groups (n = 30) were performed using Cone-beam Computed Tomography, then immersed for 20 min in three disinfectants as follows: group VCO was immersed in 100% Virgin Coconut Oil, group GA was immersed in 2% Glutaraldehyde, and group EA was immersed in 70% Ethyl Alcohol. Post-disinfection scans of the first half of the three study groups (n = 30) were performed and then compared morphologically and volumetrically using an analyzing software program The second half of the three control groups (n* = 30) were soaked for 20 min in sterile distilled water as follows: group VCO*, group GA*, and group EA* for the assessment of the antimicrobial effectiveness of the three tested disinfectants. RESULTS: At the morphological assessment of the dimensional changes, group VCO were the most accurate with the lowest mean deviation value of 0.12 ± 0.02 mm and root mean square value of 0.12 mm, group GA and group EA were less accurate with mean deviation value of = 0.22 ± 0.05 mm and = 0.19 ± 0.03 mm and root mean square value of 0.22 and 0.20 respectively (p < 0.001). At the volumetric assessment, group VCO showed lower volumetric changes with a mean deviation value of 0.17 ± 0.10 mm, root mean square value of 0.19 mm, than group GA with mean deviation value of 0.23 ± 0.10 mm, root mean square value of 0.25 mm and group EA with mean deviation value of 0.27 ± 0.11 mm, root mean square value of 0.29 mm, however, no statistically significant differences were found between the three study groups (p = 0.10). The antimicrobial effectiveness of the three tested disinfectants showed a hundred percent (100%) reduction in the total microbial count in the first half of the three study groups treated with the three disinfectants revealing no bacterial growth, however, statistically significant differences were found between the second half of the three control and the first half of the three study groups. (p < 0.001). CONCLUSIONS: Virgin Coconut Oil showed higher morphological dimensional accuracy of the tested surgical guides than Glutaraldehyde and Ethyl Alcohol without causing any volumetric dimensional changes in the 3D printed surgical guides after disinfection for 20 min and the antimicrobial effectiveness was the same between the three tested disinfectants without showing any microbial growth.