Identification of prevalent leachate percolation of municipal solid waste landfill: a case study in India.

Landfill leachate forms when waste-inherent water and percolated rainfall transfer are highly toxic, corrosive, acidic, and full of environmental pollutants. The release of leachate from municipal solid waste (MSW) landfill sites poses a severe hazard to human health and aquatic life. This study examined the impact of leachate from Delhi's Ghazipur landfill on the nearby groundwater quality. Analysis of leachate samples was done to determine various parameters such as total dissolved solids (TDS), hardness, alkalinity, electrical conductivity, pH, BOD5, COD, nitrate, sulphate, chloride and iron, and presence of coliform bacteria. Significant dissolved elements (22,690-34,525 mg/L) were observed in the samples, indicated by the high conductivity value (1156-1405 mho/cm). However, a stable pH range (6.90-7.80) of leachate samples was observed due to high alkalinity concentrations between 2123 and 3256 mg/L. The inverse distance weighing (IDW) interpolation tool from QGIS 3.22.7 developed spatial interpolated models for each parameter across the Ghazipur area. The IDW interpolated graphs of various parameters over the whole study area confirmed these contaminations. In addition, leachate and groundwater samples were physio-chemically analyzed, and temporal fluctuation in landfill waste has also been studied. The temporal fluctuation results showed that when heat is produced, transmitted, and lost throughout the waste system, the maximum temperature position fluctuates over time. The findings of this study highlight the critical importance of landfill management in reducing groundwater contamination from MSW leachate.

Analysing the influence of ground granulated blast furnace slag and steel fibre on RC beams flexural behaviour.

This study examines the effect of Ground Granulated Blast Furnace Slag (GGBS) and steel fibers on the flexural behaviour of RC beams under monotonic loading. Various percentages of GGBS were used to substitute cement, namely 0%, 20%, 40%, 60%, and 80% and fibers were added to the concrete mix as 0%, 0.5%, 1%, and 1.5% of the volume of concrete. The load-deflection behaviour of GGBS-incorporated RC beams with fibers was compared with the control RC beam. Beams were tested under load control for 28 days and 180 days. The ultimate load of the GGBS-incorporated RC beam up to 40% cement replacement was found to higher than that of the control beam. The strength of concrete is reduced by 28% and 19% when cement was partially replaced by 80% of GGBS at 28 and 180 days, respectively, compared to control concrete without fibres. Further, the analytical load-deflection response of GGBS-incorporated RC beams was determined by using several codes of practice, namely, ACI 318-11(2011), CSA A23.3-04 (2004), EC-04 (2004), and IS 456 (2000). The Codal provisions were primarily based on the effective moment of inertia, Young's modulus, and modulus of rupture, stiffness, and cracking. Average load-deflection plots obtained from experiments were compared with the computed load-deflection of analytical studies. It was found that the analytically predicted load-deflection behaviour is comparable with the corresponding average experimental load-deflection response. Moment curvature relations were also developed for RC beams.

The impact of heavy metal concentrations on aquatic insect populations in the Asan Wetland of Dehradun, Uttarakhand.

This study, centered on the Asan Wetland in Uttarakhand, examines the ecological impact of heavy metals on aquatic insects biodiversity. It highlights the detrimental effects of metals like chromium, mercury, and lead, stemming from natural and anthropogenic sources, on aquatic insects diversity. Aquatic insects, particularly sensitive to water quality, are emphasized as key indicators of environmental health, illustrating the importance of understanding and managing the influences on wetland ecosystems. Wetland ecosystems are vulnerable to various environmental stressors, including pollution from heavy metals. These toxic substances can alter water quality parameters, disrupt nutrient cycling, and negatively impact the biodiversity and ecological balance of the system. This study aimed to evaluate the impact of several heavy metals (namely Cd, As, Cu, Fe, Pb, Ni, Zn, Al, Cr) on the distribution and biodiversity of various aquatic insect species, including Coeleoptera, Diptera, Ephemeroptera, Odonata, Plecoptera, and Trichoptera. The research utilized data collected between November 2021 and October 2022 from specifically chosen sites (S1, S2, S3) within the Asan Wetland in Dehradun, Uttarakhand. After collecting and identifying samples, various statistical (Sorenson, Shannon-Weiner diversity index, Margelef index) and multivariate tests (CCA, PCA, One-way Anova), have been applied to show the effects of these parameters. This study offers significant findings regarding the distribution patterns of heavy metals, the abundance of aquatic insects, and their interconnectedness within the ecosystem of the Asan Wetland. The abundance of aquatic insects, represented by 13 genera belonging to 6 orders, was assessed at three different sites (S1, S2, and S3) within the wetland. It was concluded that the heavy metals concentration and aquatic insects' density increases and decreases vice-versa in monsoon and winter seasons might be due to unfavourable factors. These findings contribute to the understanding of ecological dynamics and potential impacts of heavy metals on aquatic biota in wetland environments.

New insights in food security and environmental sustainability through waste food management.

Food waste has been identified as one of the major factors that constitute numerous anthropogenic activities, especially in developing countries. There is a growing problem with food waste that affects every part of the waste management system, from collection to disposal; finding long-term solutions necessitates involving all participants in the food supply chain, from farmers and manufacturers to distributors and consumers. In addition to food waste management, maintaining food sustainability and security globally is crucial so that every individual, household, and nation can always get food. "End hunger, achieve food security and enhanced nutrition, and promote sustainable agriculture" are among the main challenges of global sustainable development (SDG) goal 2. Therefore, sustainable food waste management technology is needed. Recent attention has been focused on global food loss and waste. One-third of food produced for human use is wasted every year. Source reduction (i.e., limiting food losses and waste) and contemporary treatment technologies appear to be the most promising strategy for converting food waste into safe, nutritious, value-added feed products and achieving sustainability. Food waste is also employed in industrial processes for the production of biofuels or biopolymers. Biofuels mitigate the detrimental effects of fossil fuels. Identifying crop-producing zones, bioenergy cultivars, and management practices will enhance the natural environment and sustainable biochemical process. Traditional food waste reduction strategies are ineffective in lowering GHG emissions and food waste treatment. The main contribution of this study is an inventory of the theoretical and practical methods of prevention and minimization of food waste and losses. It identifies the trade-offs for food safety, sustainability, and security. Moreover, it investigates the impact of COVID-19 on food waste behavior.

A state-of-art-review on emerging contaminants: Environmental chemistry, health effect, and modern treatment methods.

Pollution problems are increasingly becoming e a priority issue from both scientific and technological points of view. The dispersion and frequency of pollutants in the environment are on the rise, leading to the emergence have been increasing, including of a new class of contaminants that not only impact the environment but also pose risks to people's health. Therefore, developing new methods for identifying and quantifying these pollutants classified as emerging contaminants is imperative. These methods enable regulatory actions that effectively minimize their adverse effects to take steps to regulate and reduce their impact. On the other hand, these new contaminants represent a challenge for current technologies to be adapted to control and remove emerging contaminants and involve innovative, eco-friendly, and sustainable remediation technologies. There is a vast amount of information collected in this review on emerging pollutants, comparing the identification and quantification methods, the technologies applied for their control and remediation, and the policies and regulations necessary for their operation and application. In addition, This review will deal with different aspects of emerging contaminants, their origin, nature, detection, and treatment concerning water and wastewater.

Effects of Chemicals Exposure on the Durability of Geopolymer Concrete Incorporated with Silica Fumes and Nano-Sized Silica at Varying Curing Temperatures.

Durable concrete significantly reduces the spalling caused by chemical damage. The objective of current research is to substitute cement with supplementary such as fly ash (FA), ground granulated blast furnace slag (GGBS), and alccofine (AF). Additionally, the impact of nano-silica (NS) and silica fumes (SF) on the GPC durability when cured at various temperatures has been attempted. In order to perform this, GPC samples were produced by combining NS and SF at proportions of 0.5% NS + 5% SF, 1% NS + 10% SF, and 1.5% NS + 15% SF, and then cured at temperatures of 27 °C, 60 °C, 90 °C, and 120 °C, respectively. In this research, all concrete specimens were continuously immersed for twelve weeks under four different chemicals, i.e., HCl (2%), H2SO4 (2%), NaCl (6%), and Na2SO4 (6%). The influence of chemical attack on the qualities of concrete was examined by evaluating the water absorption, sorptivity, loss of mass, and loss of GPC strength. The durability aspect is also studied by visual appearance and mass loss under harmful chemical attack. The combination of GPC with integrated NS and SF affords great resistance against chemical attacks. The percentages of these two components are 1.5% and 15%. For GPC specimens, when cured at 90 °C, the resultant strength is found at its maximum.

Characterization of municipal solid waste: Measures towards management strategies using statistical analysis.

Implementing unified municipal solid waste management (MSWM) is often difficult due to socio-economic variables. However, spatial GIS models and statistical analysis of solid waste characterized by the weekdays, weekends, and festivals can somewhat mitigate the variance and assist with selecting suitable waste management methods. This paper presents the example of Rajouri, India, to propose a suitable MSWM based on Inverse Distance Weighted (IDW) intensity maps and statistical findings. The considered region was divided into different sample sites based on the local population density, and Municipal Solid Waste (MSW) was collected from four locations in each site on weekdays, weekends, and festivals. Compositional analysis of the MSW was then used to generate spatial IDW models in QGIS 3.22.7 to interpolate MSW generation over the entire area. Finally, statistical analysis was conducted to gain insight into the waste generation and accumulation trends. The results show that Rajouri produces 245 tonnes of waste daily (per capita: 0.382 kg/day) with a large organic fraction compared to other waste categories. Besides, waste generation is observed to increase over weekends and festivals due to increased consumption of material goods. Composting could serve as a vector for municipal solid waste because of its increased organic component and cost constraints. However, further research on the potential segregation techniques for the organic fraction of solid waste is needed.

Nanotechnology future in food using carbohydrate macromolecules: A state-of-the-art review.

It is commonly known that agricultural pest and disease management is achieved through the use of agricultural chemicals and other synthetic compounds, which can contaminate water, soil, and food. Using agrochemicals indiscriminately has negative effects on the environment and poor food quality. In contrast, the world's population is increasing rapidly, and arable land is diminishing daily. Traditional agricultural methods must be replaced by nanotechnology-based treatments that efficiently address both the demands of the present and the needs of the future. As a promising contributor to sustainable agriculture and food production worldwide, nanotechnology has been applied through innovative and resourceful tools. Recent advances in nanomaterial engineering have increased agricultural and food sector production and protected crops using nanoparticles (1000 nm). Agrochemicals, nutrients, and genes can now be distributed to plants in a precise and tailored manner through nanoencapsulation (nanofertilizers, nanopesticides, and genes). Despite the advancement of technology in agriculture, some areas remain unexplored. The various agricultural domains must therefore be updated in priority order. The development of long-lasting and efficient nanoparticle materials will be key to the development of future eco-friendly and nanoparticle-based technologies. We thoroughly covered the many types of nanoscale agro-materials and gave an overview of biological techniques in nano-enabled tactics that can effectively reduce plant biotic and abiotic challenges while potentially boosting plant nutritional values.

Fe3O4-multiwalled carbon nanotubes-bentonite as adsorbent for removal of methylene blue from aqueous solutions.

The contamination of water due to present of dyes, poses serious health problems. Therefore, treatment of contaminated water is necessary to resolve this problem. A tailored co-precipitation technique has been successfully used to prepare Fe3O4-multiwalled Carbon Nanotubes (MWCNTs)-Bentonite nanocomposite. The methylene blue present in aqueous solutions was removed using synthesized nanocomposite as adsorbent. The synthesized novel nanocomposite was analyzed by various characterization techniques. The scanning electron microscope analysis shows that Bentonite and Fe3O4 nanoparticles are well decorated with the MWCNTs matrix. The nanocomposite exhibited a high BET surface area of 204.01 m2/g with a pore volume of 0.367 cm3/g. The BJH adsorption average pore diameter was analyzed to be 7.2 nm. Moreover, the adsorption model was in agreement with the Redlich-Peterson model with adsorption capacity of 48.2 mg/g with a high nonlinear regression coefficient (R2 = 0.985) and a low chi-square value (χ2 = 6.18). Kinetics data were described well by pseudo-first-order and pseudo second order, models with a high non-linear regression coefficient (R2 = 0.993). Adsorption of MB dye was determined to be a non-spontaneous and endothermic process since the values of ΔG, and ΔH were positive, and the entropy value was negative. Thus, the synthesized nanocomposite established itself as a promising candidate for the water treatment process.

The phenolic components extracted from mulberry fruits as bioactive compounds against cancer: A review.

In Asia, mulberry has long been used to treat various infectious and internal ailments as a traditional medication. The compounds found in it have the potential to improve human health. Because there is no approved and defined evaluation procedure, it has not been formally or scientifically recognized. As a result of these investigations, a new frontier in traditional Chinese medicine has opened up, with the possibility of modernization, for the interaction between active components of mulberry and their biological activities. These studies have used current biotechnological technologies. For ages, mulberry has been used as an herbal remedy in Asia to cure various diseases and internal disorders. It has a high concentration of bioactive chemicals that benefit human health. The most abundant phenolic components extracted from white mulberry leaves are flavonoids (Kuwanons, Moracinflavans, Moragrols, and Morkotins), phenolic acids, alkaloids, and so forth. Flavonoids, benzofurans, chalcones, and alkaloids have been discovered to have cytotoxic effects on human cancer cell lines. There is growing evidence that mulberry fruits can potentially prevent cancer and other aging-related disorders due to their high concentration of bioactive polyphenolic-rich compounds and macro and micronutrients. Anthocyanins are rapidly absorbed after eating, arriving in the plasmalemma within 15-50 min and entirely removed after 6-8 hr. Due to a lack of an approved and consistent technique for its examination, it has yet to be formally or scientifically recognized. The mulberry plant is commercially grown for silkworm rearing, and less attention is paid to its bioactive molecules, which have a lot of applications in human health. This review paper discusses the phenolic compounds of white mulberry and black mulberry in detail concerning their role in cancer prevention.

Persistence and remote sensing of agri-food wastes in the environment: Current state and perspectives.

Food demand is expected to increase globally by 60-110% from 2005 to 2050 due to diet shifts and population growth. This growth in food demand leads to the generation of enormous agri-food wastes (AFWs), which could be classified into pre-consumption and post-consumption. The AFW represents economic losses for all stakeholders along food supply chains, including consumers. It is reported that the direct financial, social, and environmental costs of food waste are 1, 0.9, and 0.7 trillion USD/year, respectively. Diverse conventional AFW management approaches are employed at the different life cycle levels (entre supply chain). The review indicates that inadequate transportation, erroneous packaging, improper storage, losses during processing, contamination, issues with handling, and expiry dates are the main reason for the generation of AFWs in the supply chain. Further, various variables such as cultural, societal, personal, and behavioral factors contribute to the AFW generation. The selection of a specific valorization technology is based on multiple physicochemical and biological parameters. Furthermore, other factors like heterogeneity of the AFWs, preferable energy carriers, by-products management, cost, end-usage applications, and environmental legislative and disposal processes also play a crucial role in adopting suitable technology. Valorization of AFW could significantly impact both economy and the environment. AFWs have been widely investigated for the development of engineered added-value biomaterials and renewable energy production. Considering this, this study has been carried out to highlight the significance of AFW cost, aggregation, quantification, and membrane-based strategies for its management. The study also explored the satellite remote sensing data for Spatio-temporal monitoring, mapping, optimization, and management of AFW management. Along with this, the study also explained the most recent strategies for AFW valorization and outlined the detailed policy recommendation along with opportunities and challenges. The review suggested that AFW should be managed using a triple-bottom-line strategy (economic, social, and environmental sustainability).

Microplastics: Occurrences, treatment methods, regulations and foreseen environmental impacts.

Microplastics are a silent threat that represent a high degree of danger to the environment in its different ecosystems and of course will also have an important impact on the health of living organisms. It is evident the need to have effective treatments for their treatment, however this is not a simple task, this as a result of the behavior of microplastics in wastewater treatment plants due to their different types and nature, their long molecular chain, reactivity against water, size, shape and the functional groups they carry. Wastewater treatment plants are at the circumference of the release of these wastes into the environment. They often act as a source of many contaminations, which makes this problem more complex. Challenges such as detection in the current scenario using the latest analytical techniques impede the correct understanding of the problem. Due to microplastics, treatment plants have operational and process stability problems. This review paper will present the in-depth situation of occurrence of microplastics, their detection, conventional and advanced treatment methods as well as implementation of legislations worldwide in a comprehensive manner. It has been observed that no innovative or new technologies have emerged to treat microplastics. Therefore, in this article, technologies targeting wastewater treatment plants are critically analyzed. This will help to understand their fate, but also to develop state-of-the-art technologies or combinations of them for the selective treatment of microplastics. The pros and cons of the treatment methods adopted and the knowledge gaps in legislation regarding their implementation are also comprehensively analyzed. This critical work will offer the development of new strategies to restrict microplastics.

Biomedical and catalytic applications of agri-based biosynthesized silver nanoparticles.

Nanotechnology has been recognized as the emerging field for the synthesis, designing, and manipulation of particle structure at the nanoscale. Its rapid development is also expected to revolutionize industries such as applied physics, mechanics, chemistry, and electronics engineering with suitably tailoring various nanomaterials. Inorganic nanoparticles such as silver nanoparticles (Ag-NPs) have garnered more interest with their diverse applications. In correspondence to green chemistry, researchers prioritize green synthetic techniques over conventional ones due to their eco-friendly and sustainable potential. Green-synthesized NPs have proven more beneficial than those synthesized by conventional methods because of capping by secondary metabolites. The present study reviews the various means being used by the researchers for the green synthesis of Ag-NPs. The morphological characteristics of these NPs as obtained from numerous characterization techniques have been explored. The potential applications of bio-synthesized Ag-NPs viz. Antimicrobial, antioxidant, catalytic, and water remediation along with the plausible mechanisms have been discussed. In addition, toxicity analysis and biomedical applications of these NPs have also been reviewed to provide a detailed overview. The study signifies that biosynthesized Ag-NPs can be efficiently used for various applications in the biomedical and industrial sectors as an environment-friendly and efficient tool.

Efficient removal of ibuprofen and ofloxacin pharmaceuticals using biofilm reactors for hospital wastewater treatment.

Hospital wastewater is harmful to the environment and human health due to its complex chemical composition and high potency towards becoming a source of disease outbreaks. Due to these complexities, its treatment is neither efficient nor cost-effective. It is a challenging issue that requires immediate attention. This effort focuses on the treatment of hospital wastewater (HWW) by removing two selected drugs, namely ibuprofen (IBU) and ofloxacin (OFX) using individual biological treatment methods, such as moving bed biofilm reactors (MBBR) and physicochemical treatment, such as ozonation and peroxane process. The both methods are compared to find the best method overall based on effectiveness and removal efficiency. The optimal removal for ozone dosing range was nitrate (9.00% and 62.00%), biological oxygen demand (BOD) (92.00% and 64.00%), and chemical oxygen demand (COD) (96.00% and 92.00%) that required at least 10 min to reach considerable degradation. The MBBR process assured a better performance for ibuprofen removal, overall. The IBU and OFX removal was found to be 14.32-96.00% at a higher COD value and 11.33-94.00% at a lower COD value due to its biodegradation. This work strives to pave the way forward to build an HWW treatment technology using integrated MBBR processes for better efficiency and cost-effectiveness.

Energy generation and revenue potential from municipal solid waste using system dynamic approach.

The Municipal Solid Waste (MSW) generation per capita in developing countries is generally said to grow in proportion to the gross national product. Composting and waste to energy have a brief history as management strategies for MSW in India and as alternatives to landfilling. Analysis of Energy generation and compost potential from waste can minimize the impact of MSW on the environment with the added advantage of providing a local source of energy. The study has been carried out to develop a system dynamic (SD) model to predict the energy generation, treatment, and cost analysis for MSW up to 2030. The predictive model developed in this study showed the generation rate of electrical energy potential augmented from 0 in 2001 to 58,380 MWh in 2007 and 319,875 MWh in 2030. Whereas, the production rate of compost reduced from 77,000 tonnes in 2001 to 45,000 tonnes in 2006 and then improved to 390,000 tonnes in 2030. In addition, the predicted revenue generated from different treatment facilities increased from 0 in 2001 to Rs.335 million (4.36 million USD) in 2007 and Rs.2569 million (33.4 million USD) in 2030. As a result, revenue generated could cover the budgets required for MSW treatment and disposal services in 2030, where the required budget is negative because revenue exceeds expenditures. The developed SD model can improve a municipal solid waste management system for any City.

Current solid waste management strategies and energy recovery in developing countries - State of art review.

Solid waste generation has rapidly increased due to the worldwide population, urbanization, and industrialization. Solid waste management (SWM) is a significant challenge for a society that arises local issues with global consequences. Thus, solid waste management strategies to recycle waste products are promising practices that positively impact sustainable goals. Several developed countries possess excellent solid waste management strategies to recycle waste products. Developing countries face many challenges, such as municipal solid waste (MSW) sorting and handling due to high population density and economic instability. This mismanagement could further expedite harmful environmental and socioeconomic concerns. This review discusses the current solid waste management and energy recovery production in developing countries; with statistics, this review provides a comprehensive revision on energy recovery technologies such as the thermochemical and biochemical conversion of waste with economic considerations. Furthermore, the paper discusses the challenges of SWM in developing countries, including several immediate actions and future policy recommendations for improving the current status of SWM via harnessing technology. This review has the potential of helping municipalities, government authorities, researchers, and stakeholders working on MSW management to make effective decisions for improved SWM for achieving sustainable development.

Sustainable green nanoadsorbents for remediation of pharmaceuticals from water and wastewater: A critical review.

In the last three decades, pharmaceutical research has increased tremendously to offer safe and healthy life. However, the high consumption of these harmful drugs has risen devastating impact on ecosystems. Therefore, it is worldwide paramount concern to effectively clean pharmaceuticals contaminated water streams to ensure safer environment and healthier life. Nanotechnology enables to produce new, high-technical material, such as membranes, adsorbent, nano-catalysts, functional surfaces, coverages and reagents for more effective water and wastewater cleanup processes. Nevertheless, nano-sorbent materials are regarded the most appropriate treatment technology for water and wastewater because of their facile application and a large number of adsorbents. Several conventional techniques have been operational for domestic wastewater treatment but are inefficient for pharmaceuticals removal. Alternatively, adsorption techniques have played a pivotal role in water and wastewater treatment for a long, but their rise in attraction is proportional with the continuous emergence of new micropollutants in the aquatic environment and new discoveries of sustainable and low-cost adsorbents. Recently, advancements in adsorption technique for wastewater treatment through nanoadsorbents has greatly increased due to its low production cost, sustainability, better physicochemical properties and high removal performance for pharmaceuticals. Herein, this review critically evaluates the performance of sustainable green nanoadsorbent for the remediation of pharmaceutical pollutants from water. The influential sorption parameters and interaction mechanism are also discussed. Moreover, the future prospects of nanoadsorbents for the remediation of pharmaceuticals are also presented.

Effect of seasonal variation on the occurrences of high-risk pharmaceutical in drain-laden surface water: A risk analysis of Yamuna River.

The occurrence of pharmaceutical residues in the aquatic ecosystem is an emerging concern of environmentalists. This study primarily investigated the seasonal variation of high-priority pharmaceutical residues in the Yamuna River, accompanied by 22 drains discharge from different parts of Delhi. Five sampling sites were selected for analyzing high-priority pharmaceuticals along with physico-chemical and biological parameters for 3 season's viz. pre-monsoon (PrM), monsoon (DuM), and post-monsoon (PoM), respectively. The maximum occurrences were detected during the PoM, compared to the PrM and DuM seasons. The maximum concentration of BOD, COD, and Phosphate was detected at the last sampling station (SP-5). Similarly, all targeted pharmaceuticals concentration were maximum at the last sampling point i.e. Okhla barrage (SP-5, max: DIC = 556.1 ng/l, IBU = 223.4 ng/l, CAR = 183.1 ng/l, DIA = 457.8 ng/l, OFL = 1726.5 ng/l, FRU = 312.2 ng/l and SIM = 414.9 ng/l) except at Barapulla downstream (SP-4, max: ERY = 178.1 ng/l). The mean concentrations of Fecal coliform (FC) ranged from 1700 to 6500 CFU/100 ml. The maximum colonies were detected in PrM season (6500 CFU/100 ml) followed by PoM (5800 CFU/100 ml) and least in DuM (1700 CFU/100 ml). Risk quotient (RQ) analysis of high-priority pharmaceuticals indicated high ecotoxicological risks exposure (>1) from DIC, DIA, OFL, and SIM in all seasons at all the sampling sites. However, lower risk was predicted for IBU, CAR, ERY, and FRU, respectively. This risk assessment indicated an aquatic ecosystem potentially exposed to high risks from these pharmaceutical residues. Moreover, seasonal agricultural application, rainfall, and temperature could influence the levels and compositions of pharmaceutical residue in the aquatic ecosystem. Hence, attention is required particularly to this stream since it is only a local lifeline source for urban consumers for domestic water supply and farmers for cultivation.

Monitoring the presence and persistence of SARS-CoV-2 in water-food-environmental compartments: State of the knowledge and research needs.

The recent spread of severe acute respiratory syndrome coronavirus (SAR-CoV-2) and the accompanied coronavirus disease 2019 (COVID-19) has continued ceaselessly despite the implementations of popular measures, which include social distancing and outdoor face masking as recommended by the World Health Organization. Due to the unstable nature of the virus, leading to the emergence of new variants that are claimed to be more and rapidly transmissible, there is a need for further consideration of the alternative potential pathways of the virus transmissions to provide the needed and effective control measures. This review aims to address this important issue by examining the transmission pathways of SARS-CoV-2 via indirect contacts such as fomites and aerosols, extending to water, food, and other environmental compartments. This is essentially required to shed more light regarding the speculation of the virus spread through these media as the available information regarding this is fragmented in the literature. The existing state of the information on the presence and persistence of SARS-CoV-2 in water-food-environmental compartments is essential for cause-and-effect relationships of human interactions and environmental samples to safeguard the possible transmission and associated risks through these media. Furthermore, the integration of effective remedial measures previously used to tackle the viral outbreaks and pandemics, and the development of new sustainable measures targeting at monitoring and curbing the spread of SARS-CoV-2 were emphasized. This study concluded that alternative transmission pathways via human interactions with environmental samples should not be ignored due to the evolving of more infectious and transmissible SARS-CoV-2 variants.

COVID-19 transmission, vulnerability, persistence and nanotherapy: a review.

End 2019, the zoonotic severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2), named COVID-19 for coronavirus disease 2019, is the third adaptation of a contagious virus following the severe acute respiratory syndrome coronavirus in 2002, SARS-CoV, and the Middle East respiratory syndrome virus in 2012, MERS-CoV. COVID-19 is highly infectious and virulent compared to previous outbreaks. We review sources, contagious routes, preventive measures, pandemic, outbreak, epidemiology of SARS-CoV, MERS-CoV and SARS-CoV-2 from 2002 to 2020 using a Medline search. We discuss the chronology of the three coronaviruses, the vulnerability of healthcare workers, coronaviruses on surface and in wastewater, diagnostics and cures, and measures to prevent spreading.