Nano Groove and Prism-Structured Triboelectric Nanogenerators.

Enhancing the output power of triboelectric nanogenerators (TENGs) requires the creation of micro or nano-features on polymeric triboelectric surfaces to increase the TENGs' effective contact area and, therefore, output power. We deploy a novel bench-top fabrication method called dynamic Scanning Probe Lithography (d-SPL) to fabricate massive arrays of uniform 1 cm long and 2.5 µm wide nano-features comprising a 600 nm deep groove (NG) and a 600 nm high triangular prism (NTP). The method creates both features simultaneously in the polymeric surface, thereby doubling the structured surface area. Six thousand pairs of NGs and NTPs were patterned on a 6×5 cm2 PMMA substrate. It was then used as a mold to structure the surface of a 200 µm thick Polydimethylsiloxane (PDMS) layer. We show that the output power of the nano-structured TENG is significantly more than that of a TENG using flat PDMS films, at 12.2 mW compared to 2.2 mW, under the same operating conditions (a base acceleration amplitude of 0.8 g).

Control of Halogen Atom in Inorganic Metal-Halide Perovskites Enables Large Piezoelectricity for Electromechanical Energy Generation.

Regulating the strain of inorganic perovskites has emerged as a critical approach to control their electronic and optical properties. Here, an alternative strategy to further control the piezoelectric properties by substituting the halogen atom (I/Br) in the CsPbX3 perovskite (X = Cl, Br) structure is adopted. A series of piezoelectric materials with excellent piezoelectric coefficients (d33 ) are unveiled. Iodine-incorporated CsPbBr2 I demonstrates the record intrinsic piezoelectric response (d33 ≈47 pC N-1 ) among all inorganic metal halide perovskites. This leads to an excellent electrical output power of ≈ 0.375 mW (24.8 µW cm-2 N-1 ) in the piezoelectric energy generator (PEG) which is higher than those of the pristine/mixed perovskite references with CsPbX3 (X = I, Br, Cl). With its structural phase remaining unchanged, the strained CsPbBr2 I retains its superior piezoelectricity in both thin film and nanocrystal powder forms, further demonstrating its repeatability and versatility of applications. The origin of high piezoelectricity is found to be due to halogen-induced anisotropic lattice strain in the unit-cell along the c-axis, and octahedral distortion. This study reveals an avenue to design new piezoelectric materials by modifying their halide constituents and paves the way to design efficient PEGs for improved electromechanical energy conversion.

Large piezoelectric response in a Jahn-Teller distorted molecular metal halide.

Piezoelectric materials convert between mechanical and electrical energy and are a basis for self-powered electronics. Current piezoelectrics exhibit either large charge (d33) or voltage (g33) coefficients but not both simultaneously, and yet the maximum energy density for energy harvesting is determined by the transduction coefficient: d33*g33. In prior piezoelectrics, an increase in polarization usually accompanies a dramatic rise in the dielectric constant, resulting in trade off between d33 and g33. This recognition led us to a design concept: increase polarization through Jahn-Teller lattice distortion and reduce the dielectric constant using a highly confined 0D molecular architecture. With this in mind, we sought to insert a quasi-spherical cation into a Jahn-Teller distorted lattice, increasing the mechanical response for a large piezoelectric coefficient. We implemented this concept by developing EDABCO-CuCl4 (EDABCO = N-ethyl-1,4-diazoniabicyclo[2.2.2]octonium), a molecular piezoelectric with a d33 of 165 pm/V and g33 of ~2110 × 10-3 V m N-1, one that achieved thusly a combined transduction coefficient of 348 × 10-12 m3 J-1. This enables piezoelectric energy harvesting in EDABCO-CuCl4@PVDF (polyvinylidene fluoride) composite film with a peak power density of 43 µW/cm2 (at 50 kPa), the highest value reported for mechanical energy harvesters based on heavy-metal-free molecular piezoelectric.

Poly(vinylidene fluoride)-Stabilized Black γ-Phase CsPbI3 Perovskite for High-Performance Piezoelectric Nanogenerators.

Halide perovskite materials have been recently recognized as promising materials for piezoelectric nanogenerators (PENGs) due to their potentially strong ferroelectricity and piezoelectricity. Here, we report a new method using a poly(vinylidene fluoride) (PVDF) polymer to achieve excellent long-term stable black γ-phase CsPbI3 and explore the piezoelectric performance on a CsPbI3@PVDF composite film. The PVDF-stabilized black-phase CsPbI3 perovskite composite film can be stable under ambient conditions for more than 60 days and over 24 h while heated at 80 °C. Piezoresponse force spectroscopy measurements revealed that the black CsPbI3/PVDF composite contains well-developed ferroelectric properties with a high piezoelectric charge coefficient (d 33) of 28.4 pm/V. The black phase of the CsPbI3-based PVDF composite exhibited 2 times higher performance than the yellow phase of the CsPbI3-based composite. A layer-by-layer stacking method was adopted to tune the thickness of the composite film. A five-layer black-phase CsPbI3@PVDF composite PENG exhibited a voltage output of 26 V and a current density of 1.1 µA/cm2. The output power can reach a peak value of 25 µW. Moreover, the PENG can be utilized to charge capacitors through a bridge rectifier and display good durability without degradation for over 14 000 cyclic tests. These results reveal the feasibility of the all-inorganic perovskite for the design and development of high-performance piezoelectric nanogenerators.

Performance-Improved Highly Integrated Uniaxial Tristate Hybrid Nanogenerator for Sustainable Mechanical Energy Harvesting.

Despite advances in the development of individual nanogenerators, the level of output energy generation must be increased to meet the demands of commercial electronic systems and to broaden their scope of application. To harvest low-frequency ambient mechanical energy more efficiently, we proposed a highly integrated hybridized piezoelectric-triboelectric-electromagnetic (tristate) nanogenerator in a uniaxial structure. In its highly integrated approach, a piezoelectric nanogenerator (PENG) based on CsPbBr3 (cesium lead bromide) nanoparticles (NPs) and poly(dimethylsiloxane) (PDMS) nanocomposite was fabricated on a triboelectrically negative nanostructured polyimide (PI) substrate. A cylindrical aluminum electrode grooved with permanent magnets was directed to move along a spring-less metallic guide bounded by these nanocomposites, thus essentially forming two single-electrode mode triboelectric nanogenerators (TENGs). By its optimized material design and novel integration approach of the PENGs, TENGs, and electromagnetic generators (EMGs), this uniaxial tristate hybrid nanogenerator (UTHNG) can synergistically produce an instantaneous electrical power of 49 mW at low-frequency ambient vibration (5 Hz). The UTHNG has excellent charging characteristics, ramping up the output voltage of a 22 µF capacitor to 2.7 V in only 12 s, which is much faster than individual nanogenerators. This work will be a superior solution for harvesting low-frequency ambient energies by improving the performance of hybrid nanogenerators, potentially curtailing the technology gap for self-powered micro/nanosystems for the Internet of Things.

Sensing of ultraviolet light: a transition from conventional to self-powered photodetector.

Clouds in the sky pass almost 80% of ultraviolet (UV) radiation to the earth's surface, which has a significant impact on humankind. Conventional UV photodetectors (PDs) require an external battery, which not only increases the device size but also has a limited life span and maintenance costs can be prohibitively expensive. An alternative and more technically-sound solution would be the use of self-powered UV PDs that can operate independently, eliminating the need for an external source. Although many exciting studies have been done and state-of-the-art research is underway to successfully fabricate self-powered UV PDs, periodic reviews on this topic are deemed essential so that the technology's readiness can be properly evaluated and critical challenges can be addressed in a timely manner. In this article, the key issues and most exciting developments made in recent years on built-in electric field assisted self-powered UV PDs based on p-n homojunctions, p-n heterojunctions, and Schottky junctions followed by energy harvester integrated UV PDs are extensively reviewed. Finally, a summary and comparison of different types of self-powered UV PDs as well as future challenges that need to be addressed are discussed. This review sets a foundation providing essential insights into the present status of self-powered UV PDs with which researchers can engage and deal with the major challenges.

Porosity Modulated High-Performance Piezoelectric Nanogenerator Based on Organic/Inorganic Nanomaterials for Self-Powered Structural Health Monitoring.

In the modern era, structural health monitoring (SHM) is critically important and indispensable in the aerospace industry as an effective measure to enhance the safety and consistency of aircraft structures by deploying a reliable sensor network. The deployment of built-in sensor networks enables uninterrupted structural integrity monitoring of an aircraft, providing crucial information on operation condition, deformation, and potential damage to the structure. Sustainable and durable piezoelectric nanogenerators (PENGs) with good flexibility, high performance, and superior reliability are promising candidates for powering wireless sensor networks, particularly for aerospace SHM applications. This research demonstrates a self-powered wireless sensing system based on a porous polyvinylidene fluoride (PVDF)-based PENG, which is prominently anticipated for developing auto-operated sensor networks. Our reported porous PVDF film is made from a flexible piezoelectric polymer (PVDF) and inorganic zinc oxide (ZnO) nanoparticles. The fabricated porous PVDF-based PENG demonstrates ∼11 times and ∼8 times enhancement of output current and voltage, respectively, compared to a pure PVDF-based PENG. The porous PVDF-based PENG can produce a peak-to-peak short-circuit current of 22 µA, a peak-to-peak open-circuit voltage of 84.5 V, a peak output power of 0.46 mW (P=Voc2×Isc2), and a peak output power density of 41.02 µW/cm2 (P/A). By harnessing energy from minute vibrations, the fabricated porous PVDF-based PENG device (area of A = 11.33 cm2) can generate sufficient electrical energy to power up a customized wireless sensing and communication unit and transfer sensor data every ∼4 min. The PENG can generate sufficient electrical energy from an automobile car vibration, which reflects the scenario of potential real-life SHM systems. We anticipate that this high-performance porous PVDF-based PENG can act as a reliable power source for the sensor networks in aircraft, which minimizes potential safety risks.