Nonvolatile Phase-Only Transmissive Spatial Light Modulator with Electrical Addressability of Individual Pixels.

Active metasurfaces with tunable subwavelength-scale nanoscatterers are promising platforms for high-performance spatial light modulators (SLMs). Among the tuning methods, phase-change materials (PCMs) are attractive because of their nonvolatile, threshold-driven, and drastic optical modulation, rendering zero-static power, crosstalk immunity, and compact pixels. However, current electrically controlled PCM-based metasurfaces are limited to global amplitude modulation, which is insufficient for SLMs. Here, an individual-pixel addressable, transmissive metasurface is experimentally demonstrated using the low-loss PCM Sb2Se3 and doped silicon nanowire heaters. The nanowires simultaneously form a diatomic metasurface, supporting a high-quality-factor (∼406) quasi-bound-state-in-the-continuum mode. A global phase-only modulation of ∼0.25π (∼0.2π) in simulation (experiment) is achieved, showing ten times enhancement. A 2π phase shift is further obtained using a guided-mode resonance with enhanced light-Sb2Se3 interaction. Finally, individual-pixel addressability and SLM functionality are demonstrated through deterministic multilevel switching (ten levels) and tunable far-field beam shaping. Our work presents zero-static power transmissive phase-only SLMs, enabled by electrically controlled low-loss PCMs and individual meta-molecule addressable metasurfaces.

Novel nanocomposite-superlattices for low energy and high stability nanoscale phase-change memory.

Data-centric applications are pushing the limits of energy-efficiency in today's computing systems, including those based on phase-change memory (PCM). This technology must achieve low-power and stable operation at nanoscale dimensions to succeed in high-density memory arrays. Here we use a novel combination of phase-change material superlattices and nanocomposites (based on Ge4Sb6Te7), to achieve record-low power density ≈ 5 MW/cm2 and ≈ 0.7 V switching voltage (compatible with modern logic processors) in PCM devices with the smallest dimensions to date (≈ 40 nm) for a superlattice technology on a CMOS-compatible substrate. These devices also simultaneously exhibit low resistance drift with 8 resistance states, good endurance (≈ 2 × 108 cycles), and fast switching (≈ 40 ns). The efficient switching is enabled by strong heat confinement within the superlattice materials and the nanoscale device dimensions. The microstructural properties of the Ge4Sb6Te7 nanocomposite and its high crystallization temperature ensure the fast-switching speed and stability in our superlattice PCM devices. These results re-establish PCM technology as one of the frontrunners for energy-efficient data storage and computing.

Area-Selective Atomic Layer Deposition for Resistive Random-Access Memory Devices.

Resistive random-access memory (RRAM) is a promising technology for data storage and neuromorphic computing; however, cycle-to-cycle and device-to-device variability limits its widespread adoption and high-volume manufacturability. Improving the structural accuracy of RRAM devices during fabrication can reduce these variabilities by minimizing the filamentary randomness within a device. Here, we studied area-selective atomic layer deposition (AS-ALD) of the HfO2 dielectric for the fabrication of RRAM devices with higher reliability and accuracy. Without requiring photolithography, first we demonstrated ALD of HfO2 patterns uniformly and selectively on Pt bottom electrodes for RRAM but not on the underlying SiO2/Si substrate. RRAM devices fabricated using AS-ALD showed significantly narrower operating voltage range (2.6 × improvement) and resistance states than control devices without AS-ALD, improving the overall reliability of RRAM. Irrespective of device size (1 × 1, 2 × 2, and 5 × 5 µm2), we observed similar improvement, which is an inherent outcome of the AS-ALD technique. Our demonstration of AS-ALD for improved RRAM devices could further encourage the adoption of such techniques for other data storage technologies, including phase-change, magnetic, and ferroelectric RAM.

Probing the Melting Transitions in Phase-Change Superlattices via Thin Film Nanocalorimetry.

Phase-change superlattices with nanometer thin sublayers are promising for low-power phase-change memory (PCM) on rigid and flexible platforms. However, the thermodynamics of the phase transition in such nanoscale superlattices remain unexplored, especially at ultrafast scanning rates, which is crucial for our fundamental understanding of superlattice-based PCM. Here, we probe the phase transition of Sb2Te3 (ST)/Ge2Sb2Te5 (GST) superlattices using nanocalorimetry with a monolayer sensitivity (∼1 Å) and a fast scanning rate (105 K/s). For a 2/1.8 nm/nm Sb2Te3/GST superlattice, we observe an endothermic melting transition with an ∼240 °C decrease in temperature and an ∼8-fold decrease in enthalpy compared to those for the melting of GST, providing key thermodynamic insights into the low-power switching of superlattice-based PCM. Nanocalorimetry measurements for Sb2Te3 alone demonstrate an intrinsic premelting similar to the unique phase transition of superlattices, thus revealing a critical role of the Sb2Te3 sublayer within our superlattices. These results advance our understanding of superlattices for energy-efficient data storage and computing.

Energy Efficient Neuro-Inspired Phase-Change Memory Based on Ge4 Sb6 Te7 as a Novel Epitaxial Nanocomposite.

Phase-change memory (PCM) is a promising candidate for neuro-inspired, data-intensive artificial intelligence applications, which relies on the physical attributes of PCM materials including gradual change of resistance states and multilevel operation with low resistance drift. However, achieving these attributes simultaneously remains a fundamental challenge for PCM materials such as Ge2 Sb2 Te5 , the most commonly used material. Here bi-directional gradual resistance changes with ≈10× resistance window using low energy pulses are demonstrated in nanoscale PCM devices based on Ge4 Sb6 Te7 , a new phase-change nanocomposite material . These devices show 13 resistance levels with low resistance drift for the first 8 levels, a resistance on/off ratio of ≈1000, and low variability. These attributes are enabled by the unique microstructural and electro-thermal properties of Ge4 Sb6 Te7 , a nanocomposite consisting of epitaxial SbTe nanoclusters within the Ge-Sb-Te matrix, and a higher crystallization but lower melting temperature than Ge2 Sb2 Te5 . These results advance the pathway toward energy-efficient analog computing using PCM.

Fast-Response Flexible Temperature Sensors with Atomically Thin Molybdenum Disulfide.

Real-time thermal sensing on flexible substrates could enable a plethora of new applications. However, achieving fast, sub-millisecond response times even in a single sensor is difficult, due to the thermal mass of the sensor and encapsulation. Here, we fabricate flexible monolayer molybdenum disulfide (MoS2) temperature sensors and arrays, which can detect temperature changes within a few microseconds, over 100× faster than flexible thin-film metal sensors. Thermal simulations indicate the sensors' response time is only limited by the MoS2 interfaces and encapsulation. The sensors also have high temperature coefficient of resistance, ∼1-2%/K and stable operation upon cycling and long-term measurement when they are encapsulated with alumina. These results, together with their biocompatibility, make these devices excellent candidates for biomedical sensor arrays and many other Internet of Things applications.

Ultra-low-energy programmable non-volatile silicon photonics based on phase-change materials with graphene heaters.

Silicon photonics is evolving from laboratory research to real-world applications with the potential to transform many technologies, including optical neural networks and quantum information processing. A key element for these applications is a reconfigurable switch operating at ultra-low programming energy-a challenging proposition for traditional thermo-optic or free carrier switches. Recent advances in non-volatile programmable silicon photonics based on phase-change materials (PCMs) provide an attractive solution to energy-efficient photonic switches with zero static power, but the programming energy density remains high (hundreds of attojoules per cubic nanometre). Here we demonstrate a non-volatile electrically reconfigurable silicon photonic platform leveraging a monolayer graphene heater with high energy efficiency and endurance. In particular, we show a broadband switch based on the technologically mature PCM Ge2Sb2Te5 and a phase shifter employing the emerging low-loss PCM Sb2Se3. The graphene-assisted photonic switches exhibited an endurance of over 1,000 cycles and a programming energy density of 8.7 ± 1.4 aJ nm-3, that is, within an order of magnitude of the PCM thermodynamic switching energy limit (~1.2 aJ nm-3) and at least a 20-fold reduction in switching energy compared with the state of the art. Our work shows that graphene is a reliable and energy-efficient heater compatible with dielectric platforms, including Si3N4, for technologically relevant non-volatile programmable silicon photonics.

Unveiling the Effect of Superlattice Interfaces and Intermixing on Phase Change Memory Performance.

Superlattice (SL) phase change materials have shown promise to reduce the switching current and resistance drift of phase change memory (PCM). However, the effects of internal SL interfaces and intermixing on PCM performance remain unexplored, although these are essential to understand and ensure reliable memory operation. Here, using nanometer-thin layers of Ge2Sb2Te5 and Sb2Te3 in SL-PCM, we uncover that both switching current density (Jreset) and resistance drift coefficient (v) decrease as the SL period thickness is reduced (i.e., higher interface density); however, interface intermixing within the SL increases both. The signatures of distinct versus intermixed interfaces also show up in transmission electron microscopy, X-ray diffraction, and thermal conductivity measurements of our SL films. Combining the lessons learned, we simultaneously achieve low Jreset ≈ 3-4 MA/cm2 and ultralow v ≈ 0.002 in mushroom-cell SL-PCM with ∼110 nm bottom contact diameter, thus advancing SL-PCM technology for high-density storage and neuromorphic applications.

Ultralow-switching current density multilevel phase-change memory on a flexible substrate.

Phase-change memory (PCM) is a promising candidate for data storage in flexible electronics, but its high switching current and power are often drawbacks. In this study, we demonstrate a switching current density of ~0.1 mega-ampere per square centimeter in flexible superlattice PCM, a value that is one to two orders of magnitude lower than in conventional PCM on flexible or silicon substrates. This reduced switching current density is enabled by heat confinement in the superlattice material, assisted by current confinement in a pore-type device and the thermally insulating flexible substrate. Our devices also show multilevel operation with low resistance drift. The low switching current and good resistance on/off ratio are retained before, during, and after repeated bending and cycling. These results pave the way to low-power memory for flexible electronics and also provide key insights for PCM optimization on conventional silicon substrates.

Uncovering Thermal and Electrical Properties of Sb2Te3/GeTe Superlattice Films.

Superlattice-like phase change memory (SL-PCM) promises lower switching current than conventional PCM based on Ge2Sb2Te5 (GST); however, a fundamental understanding of SL-PCM requires detailed characterization of the interfaces within such an SL. Here we explore the electrical and thermal transport of SLs with deposited Sb2Te3 and GeTe alternating layers of various thicknesses. We find up to an approximately four-fold reduction of the effective cross-plane thermal conductivity of the SL stack (as-deposited polycrystalline) compared with polycrystalline GST (as-deposited amorphous and later annealed) due to the thermal interface resistances within the SL. Thermal measurements with varying periods of our SLs show a signature of phonon coherence with a transition from wave-like to particle-like phonon transport, further described by our modeling. Electrical resistivity measurements of such SLs reveal strong anisotropy (∼2000×) between the in-plane and cross-plane directions due to the weakly interacting van der Waals-like gaps. This work uncovers electrothermal transport in SLs based on Sb2Te3 and GeTe for the improved design of low-power PCM.

Thermal transport characterization of stanene/silicene heterobilayer and stanene bilayer nanostructures.

Recently, stanene and silicene based nanostructures with low thermal conductivity have incited noteworthy interest due to their prospect in thermoelectrics. Aiming at the possibility of extracting lower thermal conductivity, in this study, we have proposed and modeled stanene/silicene heterobilayer nanoribbons, a new heterostructure and subsequently characterized their thermal transport by using an equilibrium molecular dynamics simulation. In addition, the thermal transport in bilayer stanene is also studied and compared. We have computed the thermal conductivity of the stanene/silicene and bilayer stanene nanostructures to characterize their thermal transport phenomena. The studied nanostructures show good thermal stability within the temperature range of 100-600 K. The room temperature thermal conductivities of pristine 10 nm × 3 nm stanene/silicene hetero-bilayer and stanene bilayer are estimated to be 3.63 ± 0.27 W m-1 K-1 and 1.31 ± 0.34 W m-1 K-1, respectively, which are smaller than that of silicene, graphene and some other 2D monolayers as well as heterobilayers such as stanene/graphene and silicene/graphene. In the temperature range of 100-600 K, the thermal conductivity of our studied bilayer nanoribbons decreases with an increase in the temperature. Furthermore, we have investigated the dependence of our estimated thermal conductivity on the size of the considered nanoribbons. The thermal conductivities of both the nanoribbons are found to increase with an increase in the width of the structure. The thermal conductivity shows a similar increasing trend with the increase in the ribbon length, as well. Our results suggest that, the low thermal conductivity of our studied bilayer structures can be further decreased by nanostructuring. The significantly low thermal conductivity of the stanene/silicene heterobilayer and stanene bilayer nanoribbons realized in our study would provide a good insight and encouragement into their appealing prospect in the thermoelectric applications.

Stanene-hexagonal boron nitride heterobilayer: Structure and characterization of electronic property.

The structural and electronic properties of stanene/hexagonal boron nitride (Sn/h-BN) heterobilayer with different stacking patterns are studied using first principle calculations within the framework of density functional theory. The electronic band structure of different stacking patterns shows a direct band gap of ~30 meV at Dirac point and at the Fermi energy level with a Fermi velocity of ~0.53 × 106 ms-1. Linear Dirac dispersion relation is nearly preserved and the calculated small effective mass in the order of 0.05mo suggests high carrier mobility. Density of states and space charge distribution of the considered heterobilayer structure near the conduction and the valence bands show unsaturated π orbitals of stanene. This indicates that electronic carriers are expected to transport only through the stanene layer, thereby leaving the h-BN layer to be a good choice as a substrate for the heterostructure. We have also explored the modulation of the obtained band gap by changing the interlayer spacing between h-BN and Sn layer and by applying tensile biaxial strain to the heterostructure. A small increase in the band gap is observed with the increasing percentage of strain. Our results suggest that, Sn/h-BN heterostructure can be a potential candidate for Sn-based nanoelectronics and spintronic applications.