RESUMEN
A serious risk that harms the safe use of water and affects aquatic ecosystems is water pollution. This occurs when the water's natural equilibrium is disrupted by an excessive amount of substances, both naturally occurring and as a byproduct of human activities, that have varied degrees of toxicity. Radiation from Cs isotopes, which are common components of radioactive waste and are known for their long half-lives (30 years), which are longer than the natural decay processes, is a major source of contamination. Adsorption is a commonly used technique for reducing this kind of contamination, and zeolite chabazite has been chosen as the best adsorbent for cesium in this particular situation. The purpose of this research is to investigate a composite material based on magnesium phosphate cement (MPC). Magnesium oxide (MgO), potassium dihydrogen phosphate (KH2PO4), and properly selected retarders are used to create the MPC. The optimal conditions for this composite material are investigated through the utilization of X-ray diffraction, scanning electron microscopy, BET surface area analysis, and atomic absorption spectroscopy. The principal aim is to enable innovations in the elimination of radioactive waste-contaminated water using effective cesium removal. The most promising results were obtained by using KH2PO4 as an acid, and MgO as a base, and aiming for an M/P ratio of two or four. Furthermore, we chose zeolite chabazite as a crucial component. The best adsorption abilities for Cs were found at Qads = 106.997 mg/g for S2 and Qads = 122.108 mg/g for S1. As a result, zeolite is an eco-friendly material that is a potential usage option, with many benefits, such as low prices, stability, and ease of regeneration and use.
RESUMEN
In this study, the efficiency of mechanically alloyed Fe80Si10B10 in degrading basic red 46 azo dye is investigated. Moreover, the influences of different parameters, such as pH and time, on the elimination of the aromatic derivatives obtained as by-products of the fracture of the azo group are also analyzed. After beginning the reduction to the normal conditions of pH (4.6) and temperature, the experimental findings showed a discoloration of 97.87% after 20 min. The structure and morphology of the nanocrystalline Fe80Si10B10 powder were characterized by SEM and XRD before and after use in the degradation process. The XRD patterns of the Fe-Si-B powder after redox reaction suggest that the valent zero Fe of the alloy is the reducing agent. Powdered cork was then used as a biosorbent for the removal of the by-products generated, resulting in increasing removal percentages from pH 7 (26%) to pH 9 (62%) and a contact time of 120 min. The FTIR spectrum of the cork after adsorption shows a shift of the bands, confirming the interaction with the aromatic amines. The present findings show that metallic powders and natural cork perform well together in removing azo dye solutions and their degradation products.
RESUMEN
Soft magnetic Fe65Ni28Mn7 (at. %) alloy was successfully synthesized by mechanical alloying and spark plasma sintering (SPS) and, in parallel, the same composition was prepared by arc melting (AM) for comparison. Several SPS conditions were tested. X-ray diffraction and scanning electron microscopy were used to investigate the structure, phase composition, and morphology of the samples. It was found that mechanical alloying produced BCC and FCC supersaturated solid solution after 130 h of milling, with a fine microstructure (i.e., crystallite size of 10 nm). Spark plasma sintering performed at 750 °C and 1000 °C under two pressures of 50 MPa and 75 MPa revealed stable FCC phases. A single FCC phase was observed after the arc melting synthesis. The magnetic properties of milled powders and solids obtained by AM and SPS were investigated. The specimen consolidated by SPS at 1000 °C under the pressure of 50 MPa exhibits soft magnetic behavior (coercivity 0.07 Oe), whereas the mechanically alloyed sample revealed hard magnetic behavior. The specimen consolidated at 750 °C under a pressure of 75 MPa showed a higher compressive strength of 1700 MPa and a Vickers hardness of 425 ± 18 HV. As a result, sintering at 750 °C/75 MPa can be utilized to enhance the mechanical properties, while those sintered at 1000 °C/50 MPa increase magnetic softness.
RESUMEN
In this study, we used a novel composite material based on magnesium phosphate cement (MPC) to explore the retention of fluoride from used water. Dead-burned magnesium oxide (MgO), ammonium dihydrogen phosphate (NH4H2PO4), and a few retarders were used to create this particular substance. Several studies have corroborated the performance of using aluminum in the capture of fluoride. From this perspective, we attempted to reinforce our matrix with different quantities of aluminum, which increased the resistance of the composite in water. The optimal conditions that were obtained were evaluated and scrutinized using a range of techniques, including scanning electron microscopy (SEM), X-ray diffraction (XRD), thermogravimetric analysis (TGA), Fourier transforms infrared spectroscopy (FTIR), and Brunauer-Emmett-Teller (BET). The adsorbents demonstrated a powerful ability to remove fluoride from contaminated water and the defluoridation capacity was evaluated at 4.84 mg/g. Equilibrium modeling was carried out, and the experimental data were expressed in accordance with the Langmuir, Freundlich, Temkin, and Dubinin-Radushkevich isotherms.
RESUMEN
In this research work, new composite materials based on magnesium phosphate cement (MPC) were developed to evaluate the retention of fluorine from wastewater. This material was prepared with dead burned magnesia oxide (MgO), ammonium dihydrogen phosphate (NH4H2PO4), and some retarding agents. We chose to synthesize with hydrogen peroxide instead of water; alumina and zeolite were also added to the cement. The obtained optimal conditions were studied and analyzed by X-ray diffraction (XRD) and scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), BET, and thermogravimetric analysis (TGA). The adsorbents showed a strong ability to remove fluoride from contaminated water, and the best defluoridation capacity was evaluated as 2.21 mg/g for the H2O2 cement. Equilibrium modeling was performed, and the experimental data were presented according to the isotherms of Langmuir, Freundlich, Temkin, and Dubinin-Radushkevich.
RESUMEN
A high-entropy Fe30Co20Ni20Mn20Al10 (at%) alloy with a face-centered cubic (FCC) crystalline phase was produced through mechanical alloying. This study examined the development of its phases, microstructure, morphology, and magnetic characteristics. Scanning electron microscopy (SEM) was applied to assess the sample morphology in relation to milling times. The changes that the material underwent during milling were investigated using X-ray diffraction. The milling time affected the phase transformation. A single FCC solid solution (crystallite size = 12 nm) was found after 50 h of milling. Additionally, the magnetic characteristics were examined and shown to be associated with microstructural changes. The powder mixture exhibited behavior consistent with soft magnetics, with an Hc value of 8 Am-1 and an Ms value of 165 emu/g. The excellent soft magnetic characteristic may be related to the stability of the FCC phase, which was generated following a 30 h milling process. In addition, the low value of Ms may have originated from the presence of Al atoms in the solid solution and the development of large densities of interfaces and crystal defects.
RESUMEN
The removal of dyes from textile effluents utilizing advanced wastewater treatment methods with high efficiency and low cost has received substantial attention due to the rise in pollutants in water. The purpose of this work is to give a comprehensive analysis of the different treatments for removing chemical dyes from textile effluents. The capability and potential of conventional treatments for the degradation of dyeing compounds in aqueous media, as well as the influence of multiple parameters, such as the pH solution, initial dye concentration, and adsorbent dose, are presented in this study. This study is an overview of the scientific research literature on this topic, including nanoreductive and nanophotocatalyst processes, as well as nanoadsorbents and nanomembranes. For the purpose of treating sewage, the special properties of nanoparticles are currently being carefully researched. The ability of nanomaterials to remove organic matter, fungus, and viruses from wastewater is another benefit. Nanomaterials are employed in advanced oxidation techniques to clean wastewater. Additionally, because of their small dimensions, nanoparticles have a wide effective area of contact. Due to this, nanoparticles' adsorption and reactivity are powerful. The improvement of nanomaterial technology will be beneficial for the treatment of wastewater. This report also offers a thorough review of the distinctive properties of nanomaterials used in wastewater treatment, as well as their appropriate application and future possibilities. Since only a few types of nanomaterials have been produced, it is also important to focus on their technological feasibility in addition to their economic feasibility. According to this study, nanoparticles (NPs) have a significant adsorption area, efficient chemical reactions, and electrical conductivity that help treat wastewater effectively.
RESUMEN
In the present work, the effect of Si addition on the magnetic properties of Fe60-xCo25Ni15Six (x = 0, 5, 10, 20, and 30 at%) alloys prepared by mechanical alloying was analyzed by X-ray diffraction and magnetic vibrating sample magnetometry and SQUID. The crystallographic parameters of the bcc-solid solutions were calculated by Rietveld refinement of the X-ray diffraction patterns with Maud software. Scanning electron microscopy (SEM) was used to determine the morphology of the powdered alloys as a function of milling time. It was found that the Si addition has an important role in the increase of structural hardening and brittleness of the particles (favoring the more pronounced refinement of crystallites). The resulting nanostructure is highlighted in accordance with the concept of the structure of defects. Magnetic properties were related to the metalloid addition, formed phases, and chemical compositions. All processed samples showed a soft ferromagnetic behavior (Hc ≤ 100 Oe). The inhomogeneous evolution of the magnetization saturation as a function of milling time is explained by the magnetostriction effective anisotropy and stress induced during mechanical alloying.
RESUMEN
Heusler Ni-Mn-Sn-based alloys are good candidates for magnetic refrigeration. This application is based on cycling processes. In this work, thermal cycles (100) have been performed in three ribbons produced by melt-spinning to check the thermal stability and the magnetic response. After cycling, the temperatures were slowly shifted and the thermodynamic properties were reduced, the entropy changed at about 3-5%. Likewise, the thermomagnetic response remains similar. Thus, these candidates maintain enough thermal stability and magnetic response after cycling. Likewise, Cu addition shifts the structural transformation to higher temperatures, whereas the Curie temperature is always near 310 K. Regarding magnetic shape memory applications, the best candidate is the Ni49Mn36 Sn14Cu1 alloy.