The performance and long-term stability of low-cost separators in single-chamber bottle-type microbial fuel cells.

This study evaluates long-term stability of low-cost separators in single-chamber bottle-type microbial fuel cells with domestic wastewater. Low-cost separators tested in this study were nonwoven fabrics (NWF) of polypropylene (PP80, PP100), textile fabrics of polyphenylene sulfide (PPS), sulfonated polyphenylene sulfide (SPPS), and cellulose esters. NWF PP80 separator generated the highest power density of 280 mW/m2, which was higher than with ion-exchange membranes (cation exchange membrane; CEM = 271 mW/m2, cation exchange membrane; CMI = 196 mW/m2, Nafion = 260 mW/m2). MFC operations with other size-selective separators such as SPPS, PPS, and cellulose esters exhibited power densities of 261, 231, and 250 mW/m2, respectively. During a 280-day operation, initial power density of PP80 (278 mW/m2) was decreased to 257 mW/m2, but this decrease was smaller than with others (Nafion: 265-230 mW/m2; PP100: 220-126 mW/m2). The anode potential of around -430 mV did not change much with all separators in the long-term operation, but the initial cathode potential gradually decreased. Fouling analysis suggested that the presence of carbonaceous substance on Nafion and PP80 after 280 days of operation and Nafion was subject to be more biofouling.

Response of microbial community structure to pre-acclimation strategies in microbial fuel cells for domestic wastewater treatment.

Microbial community structures and performance of air-cathode microbial fuel cells (MFCs) inoculated with activated sludge from domestic wastewater were investigated to evaluate the effects of three substrate pre-acclimation strategies: 1, serial pre-acclimation with acetate and glucose before supplying domestic wastewater; 2, one step pre-acclimation with acetate before supplying domestic wastewater; and 3, direct supply of domestic wastewater without any pre-acclimation. Strategy 1 showed much higher current generation (1.4mA) and Coulombic efficiency (33.5%) than strategies 2 (0.7mA and 9.4%) and 3 (0.9mA and 10.3%). Pyrosequencing showed that microbial communities were significantly affected by pre-acclimation strategy. Although Proteobacteria was the dominant phylum with all strategies, Actinobacteria was abundant when MFCs were pre-acclimated with glucose after acetate. Not only anode-respiring bacteria (ARB) in the genus Geobacter but also non-ARB belonging to the family Anaerolinaceae seemed to play important roles in air-cathode MFCs to produce electricity from domestic wastewater.

Effect of gradual transition of substrate on performance of flat-panel air-cathode microbial fuel cells to treat domestic wastewater.

In order to confirm the effects of the low conductivity and biodegradability of wastewater, flat-panel air-cathode microbial fuel cells (FA-MFCs) were operated by supplying substrates with different volume ratios of domestic wastewater mixed with an artificial medium: the artificial medium only, 25% wastewater, 50% wastewater, 75% wastewater, 100% of wastewater with 500mg-COD/L by adding acetate, and raw domestic wastewater (230mg-COD/L). With the increase of wastewater ratio, the maximum power density and organic removal efficiency decreased from 187 to 60W/m3 and 51.5 to 37.4%, respectively, but the Coulombic efficiency was maintained in the range of 18.0-18.9%. The FA-MFCs could maintain their low internal resistances and overcome the decreasing conductivity. The acetate concentration was more important than the total organics for power production. This study suggests that the FA-MFC configuration has great applicability for practical applications when supplied by domestic wastewater with low conductivity and biodegradability.