Engineering Stem Cell Fate Controlling Biomaterials to Develop Muscle Connective Tissue Layered Myofibers.

Skeletal muscle connective tissue (MCT) surrounds myofiber bundles to provide structural support, produce force transduction from tendons, and regulate satellite cell differentiation during muscle regeneration. Engineered muscle tissue composed of myofibers layered within MCT has not yet been developed. Herein, a bioengineering strategy to create MCT-layered myofibers through the development of stem cell fate-controlling biomaterials that achieve both myogenesis and fibroblast differentiation in a locally controlled manner at the single construct is introduced. The reciprocal role of transforming growth factor-beta 1 (TGF-ß1) and its inhibitor as well as 3D matrix stiffness to achieve co-differentiation of MCT fibroblasts and myofibers from a human-induced pluripotent stem cell (hiPSC)-derived paraxial mesoderm is studied. To avoid myogenic inhibition, TGF-ß1 is conjugated on the gelatin-based hydrogel to control the fibroblasts' populations locally; the TGF-ß1 degrades after 2 weeks, resulting in increased MCT-specific extracellular matrix (ECM) production. The locations of myofibers and fibroblasts are precisely controlled by using photolithography and co-axial wet spinning techniques, which results in the formation of MCT-layered functional myofibers in 3D constructs. This advanced engineering strategy is envisioned as a possible method for obtaining biomimetic human muscle grafts for various biomedical applications.

Abdominal aortic calcification in patients newly diagnosed with essential thrombocythemia.

Background: Although atherosclerosis is likely to be involved in the development of arterial thrombotic events in patients with essential thrombocythemia (ET), abdominal aortic calcification (AAC) has rarely been investigated. We evaluated the prevalence and clinical relevance of AAC at the time of ET diagnosis. Methods: This retrospective study included patients newly diagnosed with ET who underwent abdominal computed tomography (CT) at the time of diagnosis between January 2002 and December 2021 at Chungnam National University Hospital, Daejeon, Korea. CT images were reviewed and an aortic calcification score was assigned. Results: Of the 94 patients (median age, 62 yr; range, 18‒90 yr), AAC was detected in 62 (66.0%). AAC was most commonly mild (33.0%), followed by moderate (22.7%) and severe (5.3%). Old age [odds ratio (OR), 34.37; 95% confidence interval (CI), 12.32‒95.91; P＜0.001] was an independent risk factor for AAC. The patients with AAC had a higher WBC count (11.8±4.7 vs. 9.7±2.9×109/L, P=0.017), higher neutrophil-to-lymphocyte ratio (4.3±2.7 vs. 3.1±1.5, P=0.039), and higher JAK2V617F positivity (81.5% vs. 58.8%, P=0.020) compared to those without AAC. AAC was an independent risk factor for arterial thrombotic vascular events that occurred before or at diagnosis of ET (OR, 4.12; 95% CI, 1.11‒15.85; P=0.034). Conclusion: AAC is common in patients with ET and is associated with arterial thrombotic events.

Effects of a graphene oxide-alginate sheet scaffold on rotator cuff tendon healing in a rat model.

BACKGROUND: Natural polymer scaffolds used to promote rotator cuff healing have limitations in terms of their mechanical and biochemical properties. This animal study aimed to investigate the effects of combined graphene oxide (GO) and alginate scaffold and the toxicity of GO on rotator cuff healing in a rat model. METHODS: First, the mechanical properties of a GO/alginate scaffold and a pure alginate scaffold were compared. The in vitro cytotoxicity of and proliferation of human tenocytes with the GO/alginate scaffold were evaluated by CCK-8 assay. For the in vivo experiment, 20 male rats were randomly divided into two groups (n = 10 each), and supraspinatus repair was performed: group 1 underwent supraspinatus repair alone, and group 2 underwent supraspinatus repair with the GO/alginate scaffold. Biomechanical and histological analyses were performed to evaluate the quality of tendon-to-bone healing 8 weeks after rotator cuff repair. RESULTS: The GO/alginate scaffold exhibited an increased maximum load (p = .001) and tensile strength (p = .001). In the cytotoxicity test, the cell survival rate with the GO/alginate scaffold was 102.08%. The proliferation rate of human tenocytes was no significant difference between the GO/alginate and alginate groups for 1, 3, 5, and 7 days. Biomechanically, group 2 exhibited a significantly greater ultimate failure load (p < .001), ultimate stress (p < .001), and stiffness (p < .001) than group 1. The histological analysis revealed that the tendon-to-bone interface in group 2 showed more collagen fibers bridging, tendon-to-bone integration, longitudinally oriented collagen fibers, and fibrocartilage formation than in group 1. CONCLUSION: A small amount of GO added to alginate improved the mechanical properties of the scaffold without evidence of cytotoxicity. At 8 weeks after rotator cuff repair, the GO/alginate scaffold improved tendon-to-bone healing without causing any signs of toxicity in a rat model.

Increased interleukin-6 and TP53 levels in rotator cuff tendon repair patients with hypercholesterolemia.

BACKGROUND: A previous study reported that hyperlipidemia increases the incidence of tears in the rotator cuff tendon and affects healing after repair. The aim of our study was to compare the gene and protein expression of torn rotator cuff tendons in patients both with and without hypercholesterolemia. METHODS: Thirty patients who provided rotator cuff tendon samples were classified into either a non-hypercholesterolemia group (n=19, serum total cholesterol [TC] <200 mg/dL) and hypercholesterolemia group (n=11, serum TC ≥240 mg/dL) based on their concentrations of serum TC. The expression of various genes of interest, including COL1A1, IGF1, IL-6, MMP2, MMP3, MMP9, MMP13, TNMD, and TP53, was analyzed by real-time quantitative reverse transcription polymerase chain reaction (qRT-PCR). In addition, Western blot analysis was performed on the proteins encoded by interleukin (IL)-6 and TP53 that showed significantly different expression levels in real-time qRT-PCR. RESULTS: Except for IGF1, the gene expression levels of IL-6, MMP2, MMP9, and TP53 were significantly higher in the hypercholesterolemic group than in the non-hypercholesterolemia group. Western blot analysis confirmed significantly higher protein levels of IL-6 and TP53 in the hypercholesterolemic group (p<0.05). CONCLUSIONS: We observed an increase in inflammatory cytokine and matrix metalloproteinase (MMP) levels in hypercholesterolemic patients with rotator cuff tears. Increased levels of IL-6 and TP53 were observed at both the mRNA and protein levels. We suggest that the overexpression of IL-6 and TP53 may be a specific feature in rotator cuff disease patients with hypercholesterolemia.

Effects of Thermal Conductive Materials on the Freeze-Thaw Resistance of Concrete.

To solve the problem of black ice, many studies are being carried out. The key in recent days is enhancing the thermal conductivity of concrete. In this study, to improve the thermal conductivity, silicon carbide was used to substitute 50% and 100% of the fine aggregate. In addition, steel fiber is not only for enhancing the mechanical properties but could enhance thermal conductive material. Hence, the arched-type steel fiber was used up to a 1% volume fraction in this study. Furthermore, graphite was used for 5% of the volume fraction for enhancing the thermal conductivity. However, thermal damage would occur due to the difference in thermal conductivity between materials. Therefore, the thermal durability must be verified first. The target application of the concrete in this study was its use as road paving material. To evaluate the thermal durability, freeze-thaw and rapid cyclic thermal attacks were performed. The thermal conductivity of the specimens was increased with the increase in thermal conductive materials. Graphite has already been reported to have a negative effect on mechanical properties, and the results showed that this was the case. However, the steel fiber compensated for the negative effect of graphite, and the silicon carbide provided a filler effect. Graphite also had a negative effect on the freeze-thaw and rapid cyclic thermal attack, but the steel fiber compensated for the reduction in thermal durability. The silicon carbide also helped to improve the thermal durability in the same way as steel fiber. Comprehensively, the steel fiber enhanced all of the properties of the tests. Using 100% silicon carbide was considered the acceptable range, but 50% of silicon carbide was the best. Graphite decreased all the properties except for the thermal conductivity. Therefore, the content of graphite or using other conductive materials used should be carefully considered in further studies.

The characterization of exosomes from fibrosarcoma cell and the useful usage of Dynamic Light Scattering (DLS) for their evaluation.

Exosomes are a type of extracellular vesicles containing mRNA, miRNA, and proteins of origin cells, which can control the characteristics of other cells or surroundings. Despite increasing evidence on oncogenic properties of tumor-derived exosomes, fibrosarcoma-derived exosomes remain largely unrevealed. While the proper extraction and characterization of exosomes is critical in exosomes research, there are various limitations in techniques to measure the size and homogeneity of exosomes. Here, we analyzed exosomes from a fibrosarcoma cell line WEHI-164 compared with a breast cancer cell line MDA-MD-231 as a control. Results from dot blot and western blot analysis demonstrated that GM1 ganglioside, and TSG101, HSC70 and GAPDH proteins were contained in exosomes from the WEHI-164 fibrosarcoma cell line. The existence of tetraspanins such as CD81, CD63 and CD9 was confirmed in the exosomes by ExoView analysis. The results obtained from TEM showed their sphere-like shapes of around 50 to 70 nm in radius. Through DLS, we found out that the mean radius of the exosomes derived from WEHI-164 and MDA-MB-231 cell lines was 94.4 nm and 107.8 nm, respectively, with high homogeneity. When comparing the radius measured by TEM with the radius measured by DLS, it was revealed that the difference between the two methods was about 40 nm. This study has significance in characterizing the molecular properties of exosomes from a fibrosarcoma, which has not been researched much before, and in providing clear evidence that DLS can be used as an efficient, convenient and noninvasive technique to simply check the homogeneity and size of exosomes.

Utilization of Waste Polysilicon Sludge in Concrete.

Increasing use of cement in the construction industry is causing an alarming increase in carbon dioxide (CO2) emissions, which is a serious environmental threat, it can be reduced by the addition of supplementary cementitious materials (SCMs). The commonly used SCMs like ground granulated blast furnace slag (GGBS), metakaolin (MK) and fly ash (FA) have been successfully used to replace the cement partially or completely. Polysilicon sludge obtained from the photovoltaic industry is also a type of waste material that can be used as SCM because it has high content of reactive SiO2. This study investigates the effects of replacing cement with polysilicon sludge in concrete. Different concrete specimens were made by replacing varying proportions of cement with polysilicon sludge and their properties, such as, fresh properties, compressive strength, heat release, chloride penetration, freeze/thaw resistance and microstructural investigations were determined. The results demonstrate that the polysilicon sludge can be used effectively to replace cement, and environmental threats associated with its disposal can be reduced.

Influence of Coarse Aggregates and Silica Fume on the Mechanical Properties, Durability, and Microstructure of Concrete.

Globally, concrete is the most widely used construction material. The composition of concrete plays an important role in controlling its overall performance. Concrete is composed of approximately 70%-80% aggregates, by volume. Therefore, it is mandatory to investigate the effect of aggregates on the performance of concrete. For this purpose, this study investigated the effect of three different coarse aggregates on the mechanical properties, durability, and microstructure of concrete. Concrete specimens were made using aggregates obtained from three regions with different mineralogies. The specimens were also made by replacing cement with silica fume. The specimens were analyzed in terms of compressive, flexural, and splitting tensile strengths, chloride penetration, carbonation, mercury intrusion porosimetry, and scanning electron microscopy. The results demonstrate that the specimens made with rougher coarse aggregates and silica fume had enhanced performance in comparison to those made with smoother aggregates.

Mechanical Properties and Sulfate Resistance of High Volume Fly Ash Cement Mortars with Air-Cooled Slag as Fine Aggregate and Polypropylene Fibers.

The depletion of natural sand and production of the huge amount of cement in the construction industry are serious threats to the environment, which can be reduced by the utilization of by-products as cement replacement material. In this study, cement was replaced with fly ash up to 45% (by weight). In addition, the natural fine aggregate was replaced with air-cooled blast furnace slag aggregate (here referred to as "slag aggregate") at a level of 50% and 100% (by weight). Polypropylene fiber was also added, at a dosage of 0.25% of binder weight. Mortar specimens were prepared and analyzed using tests for compressive, flexure, and splitting tensile strength, as well as for microhardness, and ultrasonic pulse velocity. In addition, the specimens were exposed to sulfate solution and investigated for changes in length, mass, and compressive strength. Electron microscopy and X-ray diffraction analysis were performed to examine the microstructure and phase changes of mortar specimens exposed to sulfate solution. The results indicate that mortar specimens made with 50% slag aggregate and 0.25 % fiber showed enhanced mechanical properties. The performance of slag aggregate mortars under sulfate attack was improved significantly.

Intra-abdominal necrotic lipoma diagnosed by computed tomography as a paraprostatic cyst.

A dog with a history of diarrhea and dyschezia exhibited an oval-shaped, soft-tissue opacity mass in the abdomen on radiographs. CT examination revealed a large fluid-filled structure displacing the urinary bladder, prostate, and colon. The mass had continuity with the prostate; therefore, it was tentatively diagnosed as a paraprostatic cyst. Cytologic examination was performed and the mass was considered a non-inflammatory cyst. However, after surgery, histopathologic examination revealed a necrotic, inflamed cystic lipoma. This case shows that unusual intra-abdominal lipomas may have a cystic appearance.

Monitoring of trace metals in coastal sediments around Korean Peninsula.

Spatial distributions and temporal variations of trace metals in Korean coastal sediments were investigated by determining seven metals (As, Cd, Cr, Cu, Hg, Pb, and Zn) in sediment collected from 71 stations between 2004 and 2010 (n=491). High metal concentrations were found in the southeastern coast, where there are many cities and industrial complexes, indicating that metal concentrations in Korean coastal sediment are significantly influenced by human activities associated with urbanization and industrialization. However, metal concentrations in sediment did not markedly vary temporally, which was because the coast is managed sustainably and because of the characteristics of the sediment environments. Based on the sediment quality guidelines and geoaccumulation index, Korean coastal sediments are practically unpolluted with Cd, Cr, Cu, Hg, Pb and Zn but moderately polluted with As. More intensive monitoring is required to determine the potential As sources and to understand the As geochemical cycles in Korean coastal sediments.

Chirality extension of an oxazine building block en route to total syntheses of (+)-hyacinthacine A2 and sphingofungin B.

Concise and stereocontrolled syntheses of (+)-hyacinthacine A2 and sphingofungin B were achieved via a diastereomerically enriched oxazine intermediate. The key strategies include palladium(0)-catalyzed intramolecular oxazine formation and diastereoselective nucleophilic addition to an aldehyde. (+)-Hyacinthacine A2 was synthesized in 13 steps and 10.2% overall yield and the synthesis of sphingofungin B proceeded in a linear sequence over 15 steps and 6.9% overall yield from (R)-methyl 2-benzamido-3-((tert-butyldimethylsilyl)oxy)propanoate.

Catalytic upgrading of xylan over mesoporous Y catalyst.

In-situ catalytic cracking of xylan, a model compound of hemicellulose, was carried out using pyrolysis-gas chromatography/mass spectrometry over mesoporous Y for the first time. Experiments were conducted at three different temperatures, 400 degrees C, 450 degrees C, and 500 degrees C, to investigate the effect of reaction temperature. Three different biomass-to-catalyst ratios, 1:1, 1:2, and 1:3, were tested at 500 degrees C to examine the effect of catalyst dose. In addition, the catalytic activity of mesoporous Y was compared with that of Al-MCM-41. The catalysts used were characterized by N2 adsorption-desorption, temperature programmed desorption of NH3, and X-ray diffraction. The main pyrolysis products of xylan were acids, hydrocarbons, phenolics, oxygenates, aromatics, and polycyclic aromatic hydrocarbons. Mesoporous Y, which has acid sites with larger quantity and stronger acidity than those of Al-MCM-41, was shown to enhance the quality of bio-oil to a larger extent, producing a larger quantity of high-value-added products, such as aromatics and furans.

Conversion of kraft lignin over hierarchical MFI zeolite.

Catalytic pyrolysis of kraft lignin was carried out using pyrolysis gas chromatography/mass spectrometry. Hierarchical mesoporous MFI was used as the catalyst and another mesoporous material Al-SBA-15 was also used for comparison. The characteristics of mesoporous MFI were analyzed by X-ray diffraction patterns, N2 adsorption-desorption isotherms, and temperature programmed desorption of NH3. Two catalyst/lignin mass ratios were tested: 5/1 and 10/1. Aromatics and alkyl phenolics were the main products of the catalytic pyrolysis of lignin over mesoporous MFI. In particular, the yields of mono-aromatics such as benzene, toluene, ethylbenzene, and xylene were increased substantially by catalytic upgrading. Increase in the catalyst dose enhanced the production of aromatics further, which is attributed to decarboxylation, decarbonlyation, and aromatization reactions occurring over the acid sites of mesoporous MFI.

Catalytic conversion of cellulose over mesoporous Y zeolite.

Mesoporous Y zeolite (Meso-Y) was applied, for the first time, to the catalytic pyrolysis of cellulose which is a major constituent of lignocellulosic biomass, to produce high-quality bio-oil. A representative mesoporous catalyst Al-MCM-41 was also used to compare its catalytic activity with that of Meso-Y. Pyrolysis-gas chromatography/mass spectrometry was used for the experiments. Meso-Y, with higher acidity, led to larger yields of aromatics and furans with high value-added than Al-MCM-41, resulting in the production of bio-oil with higher quality. The effect of temperature on the catalytic pyrolysis was not significant within the range of 400-500 degrees C. When the Meso-Y to cellulose ratio was increased from 1/1 via 2/1 to 3/1, the deoxygenation efficiency increased, leading to increased yield of aromatics.

Bio-oil upgrading via catalytic pyrolysis of waste mandarin residue over SBA-15 catalysts.

Mesoporous SBA-15-based catalysts were applied, for the first time, to the pyrolysis of waste mandarin residue. Si-SBA-15 with few acid sites, Al-SBA-15 with a significant amount of acid sites owing to the alumination treatment, and Pt/Al-SBA-15, which was synthesized by incorporating 7.1-nm Pt nanoparticles on Al-SBA-15, were used. Pyrolysis experiments were conducted by pyrolysis gas chromatography/mass spectroscopy to determine the catalytic activities of the catalysts used. X-ray diffraction, nitrogen adsorption, NH3-temperature-programmed desorption and transmission electron microscopy were used to characterize the catalysts. Al-SBA-15 produced higher quality bio-oil than Si-SBA-15 due to its better deoxygenation and cracking performance stemming from the presence of acid sites. Pt/Al-SBA-15 showed the highest oxygenate conversion as well as the largest yield of high-value-added compounds, such as aromatics, low-molecular-mass hydrocarbons and furans.

Catalytic pyrolysis of waste mandarin over nanoporous materials.

Catalytic pyrolysis of waste mandarin was performed using nanoporous catalysts. AI-MCM-41 and Meso-MFI, which had different acid characteristics, were used. In addition, the characteristics of Pt/Meso-MFI were compared with those of Meso-MFI. To analyze the characteristics of the catalyst samples, Brunauer-Emmett-Teller surface area, temperature programmed desorption of NH3, and N2 adsorption-desorption analyses were performed. In addition, pyrolysis gas chromatography/mass spectrometry was used to facilitate the direct analysis of the pyrolytic products. The products obtained from catalytic pyrolysis contained a greater amount of valuable components than did those obtained from non-catalytic pyrolysis, indicating that catalytic pyrolysis improved the quality of the bio-oil. Additionally, valuable products such as furan and aromatic compounds were produced in greater quantities when Meso-MFI was used. When Pt/Meso-MFI was used, the amounts of furan and aromatic compounds produced increased even further.

Multivariate determination of 13CO2/12CO2 ratios in exhaled mouse breath with mid-infrared hollow waveguide gas sensors.

The (12)CO2/(13)CO2 isotope ratio is a well-known marker in breath for a variety of biochemical processes and enables monitoring, e.g., of the glucose metabolism during sepsis. Using animal models-here, at a mouse intensive care unit-the simultaneous determination of (12)CO2 and (13)CO2 within small volumes of mouse breath was enabled by coupling a novel low-volume hollow waveguide gas cell to a compact Fourier transform infrared spectrometer combined with multivariate data evaluation based on partial least squares regression along with optimized data preprocessing routines.

On-chip integrated mid-infrared GaAs/AlGaAs Mach-Zehnder interferometer.

We report the design, fabrication, and first functional verification of mid-infrared (MIR; 3-12 µm) Mach-Zehnder interferometers (MZIs). The developed MIR-MZIs are entirely chip-integrated solid-state devices based on GaAs/AlGaAs technology waveguide fabricated via conventional optical lithography and reactive ion etching (RIE). Thus, fabricated MIR-MZIs were combined with a broadly tunable quantum cascade laser (tQCL) providing a wavelength coverage of 5.78-6.35 µm. MIR-MZIs have been designed with a waveguide width of 5 µm to ensure single mode behavior, avoiding optically undefined interference patterns. Several structures with different opening angles of the Y-junction were fabricated and tested for maximizing IR radiation throughput. This study demonstrates the feasibility of the very first chip-integrated mid-infrared Mach-Zehnder structures via interference patterns produced by minute amounts of water deposited at different positions of the MIR-MZI structure.

Observation of methanol behavior in fuel cells in situ by NMR spectroscopy.

The chemical conversion of methanol in direct methanol fuel cells was followed in situ by NMR spectroscopy. Comparing data of the methanol oxidation on Pt and PtRu anode catalysts allowed the role of Ru in both Faradaic and non-Faradaic reactions to be investigated. The spatial distributions of chemicals could also be determined. (Picture: T1-T4=inlet and outlet tubes.).