RESUMEN
The novel heterometallic polyoxotitanate cage [Ti18MnO30(OEt)20(MnPhen)3] (1), obtained by solvothermal reaction of Ti(OEt)4 with Mn(AcO)3·(H2O)2 and 1,10-phenanthroline (Phen) in EtOH, has a C3 symmetric core structure containing an interstitial tetrahedral Mn(II) ion and is surrounded by three Mn(II)(Phen) fragments. The molecular structure is retained in thin film electrodes of 1 deposited by solution drop-casting onto fluorinated tin oxide (FTO). Both solid state and solution phase electrochemical measurements show dual redox couples, consistent with the two distinct Mn coordination environments in the cage structure. Sintering of 1 in air at 600 °C produces a black crystalline solid which consists of Mn-doped TiO2 (mainly in the rutile phase) together with α-Mn2O3. Such a composite semiconductor has an optical band gap of ca. 1.80 eV, similar to that of α-Mn2O3.
RESUMEN
Previous theoretical studies of C3B have suggested that boron-doped graphite is a promising H2- and Li-storage material, with large maximum capacities. These characteristics could lead to exciting applications as a lightweight H2-storage material for automotive engines and as an anode in a new generation of batteries. However, for these applications to be realized a synthetic route to bulk C3B must be developed. Here we show the thermolysis of a single-source precursor (1,3-(BBr2)2C6H4) to produce graphitic C3B, thus allowing the characteristics of this elusive material to be tested for the first time. C3B was found to be compositionally uniform but turbostratically disordered. Contrary to theoretical expectations, the H2- and Li-storage capacities are lower than anticipated, results that can partially be explained by the disordered nature of the material. This work suggests that to model the properties of graphitic materials more realistically, the possibility of disorder must be considered.
RESUMEN
Metal-doped polyoxotitanium cages (M-POTs) of the type [TixOy(OR)zMnXm] (M = a main group, transition metal or lanthanide; X = an anion such as a halide) can be regarded as molecular fragments of metal-doped TiO2. As such M-POTs can be used as structural models for the inclusion of metal ions into the TiO2 lattice and the ways in which well-defined microstructural changes affect photo-induced hole-electron separation. They are also potential organically-soluble redox-catalysts for a range of organic transformations and have been shown to be useful single-source precursors for the deposition of metal-doped TiO2. The applications of M-POTs as molecular precursors to metal-doped TiO2 offers a high degree of atomic control in the low temperature fabrication of photocatalytic thin films, which have applications in pollution control and water splitting. This perspective highlights the structural trends in M-POTs, their electronic behaviour and their applications as single-source precursors, looking at current and future trends in the development of inorganic precursors for device applications.
RESUMEN
To what extent the presence of transition metal ions can affect the optical properties of structurally well-defined, metal-doped polyoxotitanium (POT) cages is a key question in respect to how closely these species model technologically important metal-doped TiO2. This also has direct implications to the potential applications of these organically-soluble inorganic cages as photocatalytic redox systems in chemical transformations. Measurement of the band gaps of the series of closely related polyoxotitanium cages [MnTi14(OEt)28O14(OH)2] (1), [FeTi14(OEt)28O14(OH)2] (2) and [GaTi14(OEt)28O15(OH)] (3), containing interstitial Mn(II), Fe(II) and Ga(III) dopant ions, shows that transition metal doping alone does not lower the band gaps below that of TiO2 or the corresponding metal-doped TiO2. Instead, the band gaps of these cages are within the range of values found previously for transition metal-doped TiO2 nanoparticles. The low band gaps previously reported for 1 and for a recently reported related Mn-doped POT cage appear to be the result of low band gap impurities (most likely amorphous Mn-doped TiO2).
RESUMEN
Photoactive in one step! A nanocomposite water-oxidation photocatalyst was assembled by a straightforward and one-step spin-coating procedure of a Ti- and Ni-containing molecule on nanostructured WO3. The photoanode oxidizes water to O2 with good activity and stability in alkaline solution, and thereby features light absorption, charge separation and water-oxidation catalysis (see scheme).
RESUMEN
Cobalt-containing polyoxotitanates (TiCo) are excellent precursors for the simple and scalable preparation of Nocera-type CoOx water-oxidation electrocatalysts. The TiCo cages serve as a reservoir for cobalt ions in a titania matrix on fluoride-doped tin oxide electrodes, and form, in situ, the active CoOx catalyst for O2 evolution with high stability in phosphate buffer in pH neutral water.
RESUMEN
The solvothermal reactions of Ti(OEt)(4) with LnCl(3) (Ln = La, Ce) produced new Ti(28) Ln cages, in which the Ln(3+) ions are coordinated within a metallocrown arrangement, which represents the highest nuclearity cages of this type (see figure).
