Deep learning-based cardiothoracic ratio measurement on chest radiograph: accuracy improvement without self-annotation.

Background: A reproducible and accurate automated approach to measuring cardiothoracic ratio on chest radiographs is warranted. This study aimed to develop a deep learning-based model for estimating the cardiothoracic ratio on chest radiographs without requiring self-annotation and to compare its results with those of manual measurements. Methods: The U-net architecture was designed to segment the right and left lungs and the cardiac shadow, from chest radiographs. The cardiothoracic ratio was then calculated using these labels by a mathematical algorithm. The initial model of deep learning-based cardiothoracic ratio measurement was developed using open-source 247 chest radiographs that had already been annotated. The advanced model was developed using a training dataset of 729 original chest radiographs, the labels of which were generated by the initial model and then screened. The cardiothoracic ratio of the two models was estimated in an independent test set of 120 original cases, and the results were compared to those obtained through manual measurement by four radiologists and the image-reading reports. Results: The means and standard deviations of the cardiothoracic ratio were 52.4% and 9.8% for the initial model, 51.0% and 9.3% for the advanced model, and 49.8% and 9.4% for the total of four manual measurements, respectively. The intraclass correlation coefficients (ICCs) of the cardiothoracic ratio ranged from 0.91 to 0.93 between the advanced model and the manual measurements, whereas those for the initial model and the manual measurements ranged from 0.77 to 0.82. Conclusions: Deep learning-based cardiothoracic ratio estimation on chest radiographs correlated favorably with the results obtained through manual measurements by radiologists. When the model was trained on additional local images generated by the initial model, the correlation with manual measurement improved even more than the initial model alone.

Fat fraction and R2 * values of various liver masses: Initial experience with 6-point Dixon method on a 3T MRI system.

Purpose: To assess the feasibility of the 6-point Dixon method for evaluating liver masses. We also report our initial experience with the quantitative values in various liver masses on a 3T system. Materials and methods: Of 251 consecutive patients for whom 6-point Dixon was employed in abdominal magnetic resonance imaging scans between October 2020 and October 2021, 117 nodules in 117 patients with a mass diameter of more than 1 cm were included in the study. Images for measuring the proton density fat fraction (PDFF) and R2 * values were obtained using the iterative decomposition of water and fat with echo asymmetry and least-squares estimation-quantitative technique for liver imaging. Two radiologists independently measured PDFF (%) and R2 * (Hz). Inter-reader agreement and the differences between readers were examined using intra-class correlation coefficient (ICC) and the Bland-Altman method, respectively. PDFF and R2 * values in differentiating liver masses were examined. Results: The masses included hepatocellular carcinoma (n = 59), cyst (n = 20), metastasis (n = 14), hemangioma (n = 8), and others (n = 16). The ICCs for the region of interest (mm2), PDFF, and R2 * were 0.988 (95 % confidence interval (CI): 0.983, 0.992), 0.964 (95 % CI: 0.949, 0.975), and 0.962 (95 % CI: 0.941, 0.975), respectively. The differences of measurements between the readers showed that 5.1 % (6/117) and 6.0% (7/117) for PDFF and R2 * , respectively, were outside the 95 % CI. Conclusion: Our observation indicates that the 6-point Dixon method is applicable to liver masses.

Computer-Aided Detection of Subsolid Nodules on Chest Computed Tomography: Assessment of Visualization on Vessel-Suppressed Images.

OBJECTIVES: This study aimed to clarify the performance of automatic detection of subsolid nodules by commercially available software on computed tomography (CT) images of various slice thicknesses and compare it with visualization on the accompanying vessel-suppression CT (VS-CT) images. METHODS: A total of 95 subsolid nodules from 84 CT examinations of 84 patients were included. The reconstructed CT image series of each case with 3-, 2-, and 1-mm slice thicknesses were loaded into a commercially available software application (ClearRead CT) for automatic detection of subsolid nodules and generation of VS-CT images. Automatic nodule detection sensitivity was assessed for 95 nodules on each series of images acquired at 3 slice thicknesses. Four radiologists subjectively evaluated visual assessment of the nodules on VS-CT. RESULTS: ClearRead CT automatically detected 69.5% (66/95 nodules), 68.4% (65/95 nodules), and 70.5% (67/95 nodules) of all subsolid nodules in 3-, 2-, and 1-mm slices, respectively. The detection rate was higher for part-solid nodules than for pure ground-glass nodules at all slice thicknesses. In the visualization assessment on VS-CT, 3 nodules at each slice thickness (3.2%) were judged as invisible, while 26 of 29 (89.7%), 27 of 30 (90.0%), and 25 of 28 (89.3%) nodules, which were missed by computer-aided detection, were judged as visible in 3-, 2-, and 1-mm slices, respectively. CONCLUSIONS: The automatic detection rate of subsolid nodules by ClearRead CT was approximately 70% at all slice thicknesses. More than 95% of subsolid nodules were visualized on VS-CT, including nodules undetected by the automated software. Computed tomography acquisition at slices thinner than 3 mm did not confer any benefits.

Relationships between explosive and maximal triple extensor muscle performance and vertical jump height.

The purpose of this study was to examine the relationships between maximum vertical jump height and (a) rate of torque development (RTD) calculated during 2 time intervals, 0-50 milliseconds (RTD50) and 0-200 milliseconds (RTD200) after torque onset and (b) peak torque (PT) for each of the triple extensor muscle groups. Thirty recreationally active individuals performed maximal isometric voluntary contractions (MVIC) of the hip, knee and ankle extensors, and a countermovement vertical jump. Rate of torque development was calculated from 0 to 50 (RTD50) and 0 to 200 (RTD200) milliseconds after the onset of joint torque. Peak torque was identified and defined as the maximum torque value during each MVIC trial. Greater vertical jump height was associated with greater knee and ankle extension RTD50, RTD200, and PT (p ≤ 0.05). However, hip extension RTD50, RTD200, and PT were not significantly related to maximal vertical jump height (p > 0.05). The results indicate that 47.6 and 32.5% of the variability in vertical jump height was explained by knee and ankle extensor RTD50, respectively. Knee and ankle extensor RTD50 also seemed to be more closely related to vertical jump performance than RTD200 (knee extensor: 28.1% and ankle extensor: 28.1%) and PT (knee extensor: 31.4% and ankle extensor: 13.7%). Overall, these results suggest that training specifically targeted to improve knee and ankle extension RTD, especially during the early phases of muscle contraction, may be effective for increasing maximal vertical jump performance.