Correction: Klimek et al. A Comparison of the Structure and Selected Mechanical Properties of Cr/Co Alloys Obtained by Casting and Selective Laser Melting. J. Funct. Biomater. 2024, 15, 61.

In the original publication [...].

Characteristics of Si (C,N) Silicon Carbonitride Layers on the Surface of Ni-Cr Alloys Used in Dental Prosthetics.

Chromium- and cobalt-based alloys, as well as chrome-nickel steels, are most used in dental prosthetics. Unfortunately, these alloys, especially nickel-based alloys, can cause allergic reactions. A disadvantage of these alloys is also insufficient corrosion resistance. To improve the properties of these alloys, amorphous Si (C,N) coatings were deposited on the surfaces of metal specimens. This paper characterizes coatings of silicon carbide nitrides, deposited by the magnetron sputtering method on the surface of nickel-chromium alloys used in dental prosthetics. Depending on the deposition parameters, coatings with varying carbon to nitrogen ratios were obtained. The study analyzed their structure and chemical and phase composition. In addition, a study of surface wettability and surface roughness was performed. Based on the results obtained, it was found that amorphous coatings of Si (C,N) type with thicknesses of 2 to 4.5 µm were obtained. All obtained coatings increase the value of surface free energy. The study showed that Si (C,N)-type films can be used in dental prosthetics as protective coatings.

A Comparison of the Structure and Selected Mechanical Properties of Cr/Co Alloys Obtained by Casting and Selective Laser Melting.

Selective laser melting (SLM) technologies are becoming increasingly popular. The aim of the work is to compare the metallographic structure, hardness, and selected strength properties of alloys obtained by casting and by SLM, with a particular emphasis on fatigue strength. Twenty Cr/Co alloy bars were made by casting or SLM, and samples of appropriate dimensions were prepared for individual tests. The microstructures of the samples were tested by metallography, and then tested for hardness, impact strength, tensile strength, bending strength, and fatigue strength; they were also subjected to fracture after bending, tensile, fatigue, and impact tests, with the resulting fractures examined by scanning electron microscopy (SEM). Primary dendrites and small amounts of gas bubbles were present in the cast samples ground lengthwise. The SEM samples were more finer grained and uniform. Compared to the casting samples, the SLM samples demonstrated higher hardness, lower mean impact strength and higher tensile strength. The casting samples also displayed lower mean elongation values. The casting samples demonstrated slightly higher fatigue strength. The fractures of the casting samples showed an interdendritic character with clearly visible dendrites at the fracture, while those of the SLM samples were also intergranular, but finer grained. SLM generally results in better strength properties, while casting obtains slightly greater fatigue strength.

How Does Ethylenediaminetetraacetic Acid Irrigation Affect Biodentine? A Multimethod Ex Vivo Study.

The activity of biomaterials used during endodontic treatment can be affected by various factors. One of them is the chemical action of the irrigant that they are exposed to. The aim of this multimethod ex vivo study was to evaluate the influence of ethylenediaminetetraacetic acid (EDTA) on the surface appearance and chemical composition of Biodentine used in perforation repair. Twenty material specimens were prepared according to manufacturers' recommendations and divided into two setting-time-based groups, tested after 45 min (group A) and 24 h (group B) of setting. Material was irrigated with 17% EDTA solution with or without simultaneous ultrasonic activation. The surface characteristics and the chemical composition analysis of the Biodentine specimens were performed with the aid of a scanning electron microscope (SEM) and an energy dispersive spectroscopy (EDS) method, respectively. The volumetric loss of material was measured by dedicated digital software in an optical microscope. Statistical analysis was performed. The EDS study confirmed that after the rinsing protocol, the percentage content of elements differed between the groups. The EDTA rinse, whether ultrasonically activated or not, visibly affected the surface appearance and chemical composition of Biodentine. The specimens' surface subjected to irrigation was more irregular under SEM than in a control group. The US activation of the liquid amplified its impact on the tested material. The average volume loss in group A after 5 min irrigation was 3.98 µm3 for each µm2 of the chosen area and it increased up to 7.74 µm3/µm2 after the ultrasonic activation. In group B, indicated volume loss values were 6.30 and 11.70 µm3/µm2 for 5 min irrigation without and with US activation, respectively. Using a 20 min irrigation time and ultrasonic activation increased it up to 32.71 µm3/µm2. Each rinsing protocol involving irrigation with ethylenediaminetetraacetic acid modified the surface features and the chemical composition of the evaluated hydraulic tricalcium silicate cement. Further research is needed to indicate the possible impact of the observed changes on its long-term clinical performance.

An Evaluation of the Mechanical Properties of a Hybrid Composite Containing Hydroxyapatite.

There is currently a lack of scientific reports on the use of composites based on UDMA resin containing HAp in conservative dentistry. The aim of this study was therefore to determine the effect of hydroxyapatite content on the properties of a hybrid composite used in conservative dentistry. This paper compares a commercial hybrid composite with experimental composites treated with 2% by weight (b/w), 5% b/w, and 8% b/w hydroxyapatite. The composites were subjected to bending strength, compression, and diametrical compression tests, as well as those for impact strength, hardness, and tribological wear. The obtained results were subjected to statistical analysis. Increased hydroxyapatite was found to weaken the mechanical properties; however, 2% b/w and 5% b/w hydroxyapatite powder was found to achieve acceptable results. The statistical analysis showed no significant differences. HAp is an effective treatment for composites when applied at a low concentration. Further research is needed to identify an appropriate size of HAp particles that can be introduced into a composite to adequately activate the surface and modification its composition.

Effect of Sandblasting Parameters and the Type and Hardness of the Material on the Number of Embedded Al2O3 Grains.

BACKGROUND: Is abrasive blasting accompanied by the phenomenon of driving abrasive particles into the conditioned material? METHODS: Three hundred and fifteen cylindrical disks of three types of metal alloy (chromium/cobalt, chromium/nickel, titanium, and sintered zirconium dioxide) were divided into four groups (n = 35) and sandblasted at pressures of 0.2, 0.4, or 0.6 MPa with aluminum oxide (Al2O3), grain size 50, 110, or 250 µm. Then, the surface topography was examined using a scanning microscope, and the amount of embedded grain was measured using quantitative metallography. For each group, five samples were randomly selected and subjected to Vickers hardness testing. In the statistical analyses, a three-factor analysis of variance was carried out, considering the type of material, the size of gradation of the abrasive, and the amount of pressure. RESULTS: The smallest amounts of embedded abrasive (2.62) were observed in the ZrO2 treatment, and the largest (38.19) occurred in the treatment of the Ti alloy. An increase in the gradation and the pressure were a systematic increase in the amount of embedded grain. CONCLUSIONS: After abrasive blasting, abrasive particles were found on the surface of the materials. The amount of driven abrasive depends on the hardness of the processed material.

Quality of the Ceramic and Ni-Cr Alloy Joint after Al2O3 Abrasive Blasting.

The purpose of this in vitro study was to determine the effect of airborne-particle abrasion process parameters on the strength of the Ni-Cr alloy-ceramic bond. One hundred and forty-four Ni-Cr disks were airborne-particle abraded with 50, 110 and 250 µm Al2O3 at a pressure of 400 and 600 kPa. After treatment, the specimens were bonded to dental ceramics by firing. The strength of the metal-ceramic bond was determined using the shear strength test. The results were analyzed with three-way analysis of variance (ANOVA) and the Tukey honest significant difference (HSD) test (α = 0.05). The examination also considered the thermal loads (5000 cycles, 5-55 °C) to which the metal-ceramic joint is subjected during exploitation. There is a close correlation between the strength of the Ni-Cr alloy-dental ceramic joint and the alloy roughness parameters after abrasive blasting: Rpk (reduced peak height), Rsm (the mean spacing of irregularities), Rsk (skewness of the profile) and RPc (peak density). The highest strength of the Ni-Cr alloy surface bonding with dental ceramics under operating conditions is provided by abrasive blasting under 600 kPa pressure with 110 µm Al2O3 particles (p < 0.05). Both the abrasive blasting pressure and the particle size of the Al2O3 abrasive significantly affect the joint's strength (p < 0.05). The most optimal blasting parameters are 600 kPa pressure with 110 µm Al2O3 particles (p < 0.05). They allow the highest bond strength between the Ni-Cr alloy and dental ceramics to be achieved.

Evaluation of the Effect of the Addition of Hydroxyapatite on Selected Mechanical and Tribological Properties of a Flow-Type Composite.

(1) Background: The aim of the study was to determine the effect of modification with sintered hydroxyapatite (HAp) on selected mechanical and tribological properties of a flow-type composite. (2) Methods: Samples in the shapes of cuboidal beams (n = 120) and cylinders (n = 120) with the proper dimensions were prepared from a standard flow-type composite and others with the addition of 2% wt., 5% wt., and 8% wt. sintered hydroxyapatite. The bending strength, compression strength, diametral compression strength, impact resistance, hardness, and tribological properties were compared. (3) Results: In all cases, it was established that an increase in the amount of HAp caused a reduction in the bending, compression, and diametral compression strength. Increasing the amount of added HAp also reduced the impact strength, hardness, and wear resistance. However, the differences were statistically insignificant. (4) Conclusions: The addition of hydroxyapatite to a flow-type composite material worsened its mechanical and tribological properties; however, the obtained values were acceptable with 2% wt. and 5% wt. HAp.

Analysis of Stress and Displacement Fields in Prosthetic Crowns Made of Zirconium Dioxide Using Numerical Approach of Homogenization Hypothesis.

The main goal of this paper is to analyze the stress and displacement fields in prosthetic crowns made of zirconium dioxide using the numerical approach of homogenization hypothesis. The simple engineering model is developed and applied in case of vertical forces. The model is a three-dimensional simulation of molars subjected to crushing, mastication, and clenching. Two basic approaches are considered: the single prosthetic crown on a single molar, and the prosthetic bridge on two molars. The distributions of material parameters are determined for the rigid support and the elastic gum structure of the homogenized properties. The crown on a single molar is analyzed in respect of caries, which are represented by weak material parameters. Irrespective of the problem, the maximal stresses are always insignificant compared to the compressive strength for enamel, dentin, periodontium, and zirconium dioxide. In case of caries, the maximal stresses are located at the contact surface caries/crown, whereas the displacement was higher than the same parameter without caries. The stresses inside the prosthetic bridge on two molars were comparable for elastic and rigid support, and located at the same areas. The molar displacement for elastic gum was higher than for the rigid base, and additionally supplemented by the displacement of the supporting structure.

Influence of Abrasive Treatment on a Transformation of Zirconium Oxide Used in Dental Prosthetics.

Zirconium oxide is a ceramic most often used in the field of dentistry for permanently cementing the substructures of prosthetic restorations in patients. The surface of zirconium oxide should be prepared properly because in the next stage it must be covered with porcelain. The success of prosthetics treatment depends on various factors, but it has been reported that the transformation of zirconium oxide plays a key role. The purpose of the research was to investigate the effect of abrasive blasting on the transformation of zirconium oxide. The research has shown that this type of surface treatment causes the transformation of the tetragonal phase into a monoclinic one. The samples were examined using X-ray diffraction (XRD). The study confirmed the assumption.

The Effect of Irrigation with Citric Acid on Biodentine Tricalcium Silicate-Based Cement: SEM-EDS In Vitro Study.

There are various factors that may interfere with the activity of biomaterials during endodontic therapy. One of them is the canal system irrigation procedure with different rinsing solutions performed after the placement of bioactive cements. The authors investigate the influence of citric acid, a chelating agent, on the surface and the chemical composition of Biodentine tricalcium silicate-based cement using a multimethod approach. Twenty samples were divided into two groups based on the material setting time. They were subjected to citric acid irrigation with or without ultrasonic activation for 5 and 20 min. The chemical analysis was made with energy dispersive spectroscopy (EDS). The visual assessment of Biodentine surface was carried out in scanning electron microscope (SEM). The volume of material loss during the procedure was measured with Keyence optic microscope and dedicated digital software. Statistical analysis was performed. The results of the study show that the irrigation with citric acid influenced the surface appearance of the material and changed its chemical composition in both investigated groups. The ultrasonic activation (US) of the liquid has also aggravated its impact. Further research is needed to assess if that fact may change the sealing properties of the material influencing the long-term clinical outcome.

The Influence of Material Type and Hardness on the Number of Embedded Abrasive Particles during Airborne-Particle Abrasion.

(1) Background: This paper aims to determine the influence of hardness on the number of abrasive material grains (SiC) embedded on the surface metal alloys and ZrO2 during abrasion. (2) Methods: Cylindrical samples were created: 315 made of Cr/Co, Ni/Cr or Ti, and 315 made of sintered ZrO2- 3TPZ-Y. These were divided into four groups (each n = 35 samples), and were treated with SiC grain sizes 50, 110, and 250 µm at pressures 0.2, 0.4, or 0.6 MPa. The samples were then observed in SEM to study SE and BSE. The surface coverage of abrasive material particles was determined by quantitative metallography. Five samples from each group were subjected to hardness measurements. The results were compared with three-factor variance analysis with using the post hoc Tukey test. (3) Results: The highest amount (40.06) of embedded abrasive was obtained for Ti alloy with a gradation of 250µm at a pressure of 0.6 MPa. The smallest amount of embedded grain (2.66) was obtained for ZrO2 for the same treatment parameters. (4) Conclusions: The amount of embedded abrasive particles depends on the type of treated material, gradation particles, and the amount of applied pressure. Harder treated materials are more resistant to grains of abrasive becoming embedded on surface.

Corrosive Studies of a Prosthetic Ni-Cr Alloy Coated with Ti(C,N) Type Layers.

Background: Investigating the general corrosion resistance of Ti(C,N) type coatings on a prosthetic nickel alloy in the aspect of their use as protective coatings on prosthetic and orthodontic elements. Methods: Five groups of Ni-Cr alloy samples covered with Ti(C,N) type coatings differing in their carbon and nitrogen contents were used for the tests. The reference group included alloy samples without coatings. The samples were held for 105 days (2520 h) in salt spray chambers and examined by means of the NSS (neutral salt spray) and SWAAT (sea water acetic acid test) tests. After the periods of 14, 28, 81 and 105 days, the samples were removed and weighed, and their weight losses were determined. Results: In the case of each type of Ti(C,N) coating, the mass loss was lower than the mass loss of a sample without a coating, which makes it possible to state that coatings improve the corrosion resistance. No significant differences in the resistance were observed between the particular coatings. The corrosion rate of the examined coatings is close to parabolic. Conclusions: Ti(C,N) type coatings improve the resistance of a prosthetic Ni-Cr alloy and can be used as protective coatings for prosthetic and orthodontic elements.

Effect of SiC Abrasive Blasting Parameters on the Quality of the Ceramic and Ni-Cr Dental Alloy Joint.

The SiC abrasive blasting parameters are vital in ensuring a suitable bond between dental ceramics and the Ni-Cr alloy. The purpose of this in vitro test was to examine the strength of the joint between the Ni-Cr alloy and fused dental ceramics for SiC abrasive blasting at a specific pressure (400, 600 kPa) and particle size (50, 110, 250 µm) in order to determine the optimal treatment parameters. The test also accounted for thermal loads (5000 cycles, 5-55 °C) to which the metal-ceramic joint is subjected during use. One hundred and forty-four Ni-Cr cylinders were divided into six groups (n = 12) and subjected to the airborne-particle abrasion with SiC with various pressure and grit size parameters. After treatment, the specimens were rinsed, dried, fused to dental ceramics, and examined for their shear strength using the Zwick/Roell Z020 machine. The results were statistically analysed using the ANOVA analysis of variance (α = 0.05). The highest metal-ceramic joint strength was obtained for abrasive blasting with 110 and 250 µm SiC grit at a pressure of 400 kPa. This relationship was also observed after the joint was subjected to thermal loads (5000 thermocycles). Additionally, thermal loads did not significantly reduce the joint's strength compared with non-loaded joints. For small SiC abrasive grit sizes (50 µm) under pressure 400 kPa, the treatment pressure had a significant effect on the strength of the joint (p < 0.05). For larger particle sizes, the pressure had no effect. After abrasive blasting using SiC, the Ni-Cr metal-ceramic joint retained its properties, even under thermal load, ensuring the joint properties' stability during use.

Analysis of the Surface Condition and Changes in Crystallographic Structure of Zirconium Oxide Affected by Mechanical Processing.

Zirconium oxide is a material commonly used in dental prosthetics for making cups of permanent prosthetic restorations. In order to properly prepare the surface of zirconium oxide for prosthetic treatment, it must be veneered with ceramics. The quality of cup-veneered ceramics is dependent on many factors, including the surface free energy (SFE) and transformation of zirconium oxide. The aim of the study was to investigate the type of phase transition and the value of free energy of the surface subjected to machining (wet and dry grinding, polishing). Quantitative and qualitative phase identification measurements showed that mechanical treatment causes transformation of the tetragonal phase into a monoclinic phase in the zirconium oxide surface. Prepared samples were analyzed by means of X-ray diffraction (XRD), which confirmed the phenomenon of transition. Measurements of the wetting angle and the calculated values of the surface free energy (SFE) showed no significant differences between the samples subjected to each treatment.

Effect of Ni-Cr Alloy Surface Abrasive Blasting on Its Wettability by Liquid Ceramics.

An adequate surface is essential in ensuring a solid bond between the metal and dental ceramics for metal framework wettability. This work is aimed at investigating the effect of variable abrasive blasting parameters on Ni-Cr alloy surface's ability to be wetted with liquid ceramics at elevated temperatures. One-hundred and sixty-eight samples were divided into 12 groups (n = 14), which were sandblasted using variable parameters: type of abrasive (Al2O3 and SiC), the grain size of the abrasive (50, 110, and 250 µm), and processing pressure (400 and 600 kPa). After treatment, the samples were cleaned in an ultrasonic cleaner and dried under compressed air. Dental ceramics were applied to the prepared surfaces via drops, and the wettability was tested in a vacuum oven at temperatures in the range of 850-1000 °C. The results were statistically analyzed using ANOVA (α = 0.05). For all surfaces, the contact angles were less than 90° at temperatures below 875 °C. For Al2O3, the best wettability was observed for the smallest particles and, for SiC, the largest particles. The ability to wet the surface of a Ni-Cr alloy is related to its sandblasting properties, such as roughness or the percentage of embedded abrasive particles. It should not be the only factor determining the selection of abrasive blasting parameters when creating a prosthetic restoration.

The Pulp Stones: Morphological Analysis in Scanning Electron Microscopy and Spectroscopic Chemical Quantification.

Background and objectives: Pulp stones are hard tissue structures formed in the pulp of permanent and deciduous teeth. Few studies have evaluated their morphology and chemical composition. However, their formation, composition, configuration and role played in overall health status are still unclear. Clinically, they may be symptomatic; technically, they impede access during endodontic therapy, increasing the risk of treatment errors. Thus, this study aimed to morphologically analyze pulp stones and present their chemical quantification, identifying their main chemical elements. It also correlates the results with their possible induction mechanisms. Materials and Methods: Seven pulp nodules were collected from molar teeth needing endodontic treatment. The morphology of the stones was analyzed by scanning electron microscopy (SEM), and their chemical composition was determined by X-ray dispersive energy spectroscopy (EDX). Results: These structures varied considerably in shape, size and topography. The site of the stones in the pulp cavity was the factor that most affected the morphology. The majority of the stones found in the pulp chambers presented nodular morphology, while those in the root canals presented a diffuse shape, resembling root canal anatomy. The topography of the nodules showed heterogeneous relief, revealing smooth and compact areas contrasting with the rugged and porous ones. The chemical composition varied depending on the location of the nodule in the pulp cavity and the relief of the analyzed area. Radicular stones presented considerably lower calcium and phosphorus content than coronary nodules. Conclusions: The high cellularity rate of the coronal pulp predisposes this region to nodular mineralizations around injured cells. The presence of larger caliber vascular bundles and higher collagen fiber content in radicular pulp determines a diffuse morphological pattern in this region. Understanding the morphology and chemical composition of the pulp stones allows future translational pathways towards the prevention or treatment of such conditions.

The Surface Condition of Ni-Cr after SiC Abrasive Blasting for Applications in Ceramic Restorations.

Abrasive blasting is a process widely used in dentistry. One of the uses is the development of metal surfaces for connections with ceramics in fixed prosthetic restorations. The purpose of this paper was to check how the rough surface profile (width, height, and depth on unevenness) impacts the surface's condition, like its wettability and percentage of stuck abrasives. The Ni-Cr alloy surface was abrasive blasted by silicon carbide with the various pressure parameters (0.2, 0.4, and 0.6 MPa) and abrasive particle sizes (50, 110, and 250 µm). Cleaned surfaces were examined for roughness, wettability, and percentage of stuck abrasive particles on the surface. The surface after abrasive blasting using 110 µm of abrasive size and 0.4 MPa pressure has the best wettability results. The width of unevenness may cause it. When the unevenness has too small or too large width and depth, the fluids may not cover the entire cavities because of locking the air. The surface condition of dental alloys directly affects metal-ceramic connection strength. The knowledge about the impact of the abrasive blasting parameters on the bond strength will allow one to create durable dental restorations.

Comparative scanning electron microscope analysis of the enamel of permanent human, bovine and porcine teeth.

BACKGROUND: Bovine and porcine teeth are often used in in vitro experiments as substitutes of human teeth. OBJECTIVES: The aim of the present study was to perform a comparative analysis of enamel morphology of permanent human, bovine and porcine teeth under the scanning electron microscope. METHODS: As many as 10 human, 10 bovine, and 10 porcine teeth were studied. All the teeth were sectioned and the halves were randomly divided into 2 groups according to the examined tissue (vestibular enamel at the mid-height of the dental crown and in the cervical area). Human and bovine enamel was etched for 15 sec and porcine enamel for 30 sec. The scanning electron microscope analysis was performed. The length and width of enamel prisms were determined with the "Met-Ilo" 1.1 computer program. RESULTS: All enamel samples revealed the same etching pattern-Silverstone's type 2. Bovine enamel showed a similar porosity and the amount of interprismatic enamel compared to human enamel while the amount and width of interprismatic enamel bands in porcine enamel were evidently greater. The shape of the porcine prisms was visually similar to human prisms, although dimensions were significantly different. However, bovine prisms differed in form and appeared to be distinctly elongated. CONCLUSIONS: Reported findings indicate that the results of experimental studies carried out on bovine and porcine enamel should not be compared with the results obtained on human enamel.

Characteristics of Al-Si Alloys with High Melting Point Elements for High Pressure Die Casting.

This paper is devoted to the possibility of increasing the mechanical properties (tensile strength, yield strength, elongation and hardness) of high pressure die casting (HPDC) hypoeutectic Al-Si alloys by high melting point elements: chromium, molybdenum, vanadium and tungsten. EN AC-46000 alloy was used as a base alloy. The paper presents the effect of Cr, Mo, V and W on the crystallization process and the microstructure of HPDC aluminum alloy as well as an alloy from the shell mold. Thermal and derivative analysis was used to study the crystallization process. The possibility of increasing the mechanical properties of HPDC hypoeutectic alloy by addition of high-melting point elements has been demonstrated.