Processing and Functionalization of Vertical Graphene Nanowalls by Laser Irradiation.

The processing of vertical graphene nanowalls (VGNWs) via laser irradiation is proposed as a means to modulate their physicochemical properties. The effects of the number of applied pulses and fluence of each pulse are examined. Raman spectroscopy studies the effect of irradiation on the chemical structure of the VGNWs. Results show a decrease in density of defects and number of layers, which points toward a mechanism including evaporation of amorphous or loosely bonded C from defective points and recrystallization of graphene. Moreover, the effect of laser irradiation parameters on the morphology of Mo thin films deposited on VGNWs is investigated. The received thermal dosage results in the formation of particles. In this case, the number of pulses and pulse fluence are found to affect the size and distribution of these particles. The study provides a novel approach for the functionalization of VGNWs via laser irradiation, which can be extended to other graphene-based nanostructures.

Sub-ps Pulsed Laser Deposition of Boron Films for Neutron Detector Applications.

In view of the demand for high-quality thermal neutron detectors, boron films have recently attracted widespread research interest because of their special properties. In this work, we report on the deposition of boron films on silicon substrates by sub-picosecond pulsed laser deposition (PLD) at room temperature. Particular emphasis was placed on the investigation of the effect of the laser energy density (fluence) on the ablation process of the target material, as well as on the morphological properties of the resulting films. In addition, based on the study of the ablation and deposition rates as a function of the fluence, the ablation/deposition mechanisms are discussed. We show that well-adherent and stable boron films, with good quality surfaces revealing a good surface flatness and absence of cracks, can be obtained by means of the PLD technique, which proves to be a reliable and reproducible method for the fabrication of thick boron coatings that are suitable for neutron detection technology.

Environment-Induced Reversible Modulation of Optical and Electronic Properties of Lead Halide Perovskites and Possible Applications to Sensor Development: A Review.

Lead halide perovskites are currently widely investigated as active materials in photonic and optoelectronic devices. While the lack of long term stability actually limits their application to commercial devices, several experiments demonstrated that beyond the irreversible variation of the material properties due to degradation, several possibilities exist to reversibly modulate the perovskite characteristics by acting on the environmental conditions. These results clear the way to possible applications of lead halide perovskites to resistive and optical sensors. In this review we will describe the current state of the art of the comprehension of the environmental effects on the optical and electronic properties of lead halide perovskites, and of the exploitation of these results for the development of perovskite-based sensors.

Low Energy Pulsed Laser Excitation in UV Enhances the Gas Sensing Capacity of Photoluminescent ZnO Nanohybrids.

Nanohybrids, composed of luminescent zinc oxide (ZnO) nanoparticles dispersed in an inert polydimethylsiloxane (PDMS) matrix, exhibit an excellent ability to follow changes in the type and composition of their surrounding atmosphere. These changes are found to affect the UV photoluminescence (PL) emission of the ZnO-PDMS hybrids measured at room temperature. The influence of irradiation parameters, such as excitation intensity and wavelength, on the response of the ZnO-PDMS sensor against ethanol and oxygen, have been systematically investigated in a comparative study performed employing pulsed excitation at 248 and 355 nm. This study represents the first demonstration that the sensing performance of the PL-based ZnO sensors can be optimized by tuning the excitation parameters and it particularly illustrates that maintaining a low pump energy density is crucial for enhancing the sensitivity of the sensor achieving response values approaching 100%.

3D micro-structured arrays of ZnΟ nanorods.

The fabrication of nanostructures with controlled assembly and architecture is very important for the development of novel nanomaterial-based devices. We demonstrate that laser techniques coupled with low-temperature hydrothermal growth enable complex three-dimensional ZnO nanorod patterning on various types of substrates and geometries. This methodology is based on a procedure involving the 3D scaffold fabrication using Multi-Photon Lithography of a photosensitive material, followed by Zn seeded Aqueous Chemical Growth of ZnO nanorods. 3D, uniformly aligned ZnO nanorods are produced. The increase in active surface area, up to 4.4 times in the cases presented here, provides a dramatic increase in photocatalytic performance, while other applications are also proposed.

An ethanol vapor detection probe based on a ZnO nanorod coated optical fiber long period grating.

A new ethanol vapor detection probe based on an optical fiber long period grating overlaid with a zinc oxide (ZnO) nanorods layer is presented. The ZnO nanorod layer was developed onto the cladding of the fiber using aqueous chemical growth, seeded by a thin layer of metallic Zn. The growth of the ZnO nanorods overlayer onto the long period grating cladding is monitored in real time for investigating its effect on the spectral properties of the device and its subsequent role in the sensing mechanism. Results are presented, on the correlation between the growth time of the ZnO layer and the ethanol vapor detection performance. Reversible spectral changes of the notch extinction ratio of more than 4 dB were recorded for ~50 Torr of ethanol vapor concentration. In addition, photoluminescence emission studies of the ZnO overlayer performed simultaneously with the optical fiber spectral measurements, revealed significant ethanol induced changes in the intensity of the bandgap peak.