Anatomical examination of the great inguinal blood vessels in preterm and term neonates.

It is generally accepted that vessel cannulation is technically more difficult and results in more complications in neonates. A sound anatomical knowledge of the inguinal area is therefore important in the selection of appropriately sized central line catheters as well as the approach to central vessel access. Eleven stillborns were investigated. Birth weight (mean: 2,414 g, 900-4,100 g) and gestational age (mean 34 1/7 weeks', 27 6/7-42 1/7) varied within normal range. The outer diameters of the femoral artery (FA), femoral vein (FV), and great saphenous vein (GSV) were determined. The distance between the anterior superior iliac spine and the pubic tubercle was set as 100% and the vessel intersection points were calculated as percentage values of the inguinal ligament length, starting at the iliac spine. The FA has a diameter of 1.9 ± 0.5 mm without correlation to gestational age. The FA crosses the inguinal ligament centrally. The FV has a diameter of 3.1 ± 1.0 mm and does have correlation to gestational age. The FV crosses the inguinal ligament at 63-64%. The GSV has a diameter of 1.4 ± 0.7 mm. Its point of intersection at the level of the inguinal ligament is 68-70%. We conclude that cannulation of the femoral artery or vein should not be performed too far (<1 cm) from the inguinal ligament. The course of the GSV is not suitable for catheter insertion.

Cyclic long-term loading of a bilateral fixed-angle plate in comparison with tension band wiring with K-wires or cannulated screws in transverse patella fractures.

PURPOSE: A bilateral fixed-angle plate was biomechanically compared to the two currently preferred methods of osteosynthesis for transverse patella fractures. It was hypothesized that the new angle-stable implant would provide a secure and sustainable fracture fixation, superior to the established standard techniques. METHODS: Twenty-one identical patellae made of polyurethane foam (Sawbones(®)), osteotomized to create a transverse two-part fracture, were fixed with modified anterior tension wiring, cannulated lag screws with anterior tension wiring or bilateral polyaxial 2.7-mm fixed-angle plates. The testing protocol consisted of 10,000 repetitive cycles using a non-destructive physiological load between 100 and 300 N at a simulated knee flexion of 60°. RESULTS: All 21 Sawbone(®)-patellae sustained repetitive loading up to 10,000 cycles without failing. The anterior tension wire group displayed significant displacement of the fracture gap (0.7 ± 0.2 mm) during cyclic loading, while both lag screws with tension wiring and bilateral fixed-angle plates showed no fracture gap widening at all (p < 0.01). CONCLUSION: The bilateral fixed-angle plate and cannulated lag screws with anterior tension wiring preserved a constantly reduced fracture gap over 10,000 tensile cycles in contrast to modified anterior tension wiring, which exhibited significant widening of the gap after initial loading. Results of in vitro testing indicate that bilateral fixed-angle plates provide sustainable fixation stability offering a promising new option in the treatment for transverse patella fractures.

Absence of tissue ingrowth through the textile fabric in a series of explanted clinic stent-grafts.

Using the retrieved devices from one autopsy and five reoperations, the biocompatibility of explanted Talent stent-grafts was investigated to highlight the capacity of the fabric to act as an effective scaffold to regenerate a blood conduit. The autopsy device was encapsulated both internally and externally, but the capsules did not penetrate through the fabric structure. The reoperation devices showed discrete patches of compact fibrin and irregularly scattered mural thrombi. Positive staining of α-actin, tissue plasminogen activator (tPA), urokinase (uPA), urokinase receptor (uPAR), and urokinase inhibitors (PAI 1, PAI 2, PAI 3, and protease nexin), and D-dimer was more frequently identified in the autopsy sample than in the reoperation samples. This preliminary assessment shows that the stent-graft retrieved during autopsy was better healed than those explanted at reoperation.

Influence of calcaneus angle and muscle forces on strain distribution in the human Achilles tendon.

BACKGROUND: Heterogeneous distribution of tendon strain is considered to contribute to the development of the Achilles tendon overuse injuries. Force distribution between the three portions of the triceps surae muscle and position of the calcaneus might affect the extent of strain differences within the Achilles tendon. Purpose of this study was to determine the effect of changes in force distribution within the triceps muscle and changes in calcaneus position on intratendinous strain distribution of the Achilles tendon. METHODS: Five cadaveric Achilles tendons including complete triceps surae and calcaneus were dissected. Specimens were mounted in a loading simulator allowing independent force application for the three parts of triceps muscle and changes calcaneus eversion and inversion position. Strain was determined in different aspects of the Achilles tendon. FINDINGS: Changes of calcaneus position resulted in intratendinous strain differences up to 15%, changes in force distribution within the triceps muscle resulted in strain differences up to 2.5%. Calcaneal eversion was connected to a higher degree of strain in medial tendon portions, while inversion increased strain in lateral tendon portions. INTERPRETATION: Medio-lateral, proximo-distal and dorsal-ventral distribution of tendon strain is rather influenced by kinematics of the subtalar joint than by muscular imbalances within the triceps muscle. Clinical movement analyses should focus on motion pattern combining rearfoot eversion with high Achilles tendon load. The results indicate that twist of the Achilles tendon fascicles seems of paramount importance in balancing tendon strain. To get more insight into the Achilles tendon injuries pathogenesis future research should focus on methods monitoring heterogeneous distribution of strain in vivo.

Biomechanical cadaver testing of a fixed-angle plate in comparison to tension wiring and screw fixation in transverse patella fractures.

INTRODUCTION: Operative treatment of patella fractures is frequently associated with implant failure and secondary dislocation which can be attributed to the employed hardware. Therefore, a 2.7 mm fixed-angle plate designed for the treatment of patella fractures was tested biomechanically against the currently preferred methods of fixation. It was hypothesized that under simulated cyclic loading fixed-angle plating would be superior to modified anterior tension wiring or cannulated lag screws with anterior tension wiring. MATERIALS AND METHODS: Eighteen human cadaver knees, matched by bone mineral density and age, were divided into three groups of six. After setting a transverse patella fracture each group received one of the osteosyntheses mentioned above. Repetitive testing over 100 cycles was performed at non-destructive loads by simulating knee motion from 90° flexion to full extension. RESULTS: Anterior tension wiring as well as lag screws with tension wiring showed significant fracture displacement after the initial cycle already. Both constructs, lag screws plus wiring (3.7 ± 2.7 mm) as well as tension wiring alone (7.1 ± 2.2 mm) displayed fracture displacement of >2 mm which is clinically regarded as failure. Those patellae stabilized with fixed-angle plates showed no significant fracture gap widening after completion of 100 cycles (0.7 ± 0.5 mm). The differences between the fixed-angle plate group and the other two groups were statistically significant (p<0.05). CONCLUSION: In contrast to modified anterior tension wiring and cannulated lag screws with anterior tension wiring the bilateral fixed-angle plate was the only fixation device to stabilize transverse patella fractures securely and sustainably.

Impact of posterior tibial nail malpositioning on iatrogenic injuries by distal medio-lateral interlocking screws. A cadaveric study on plastinated specimens.

In intramedullary tibial nailing, multi-planar locking makes stabilization of proximal and distal metaphyseal fractures possible. A known complication in intramedullary nailing of the tibia is iatrogenic injury to neuro-vascular structures caused by the insertion of locking screws. As shown in previous studies, the distal positioning of the nail is important, as it determines the course of the locking bolts. The goal of the present study was to display the consequences of posterior nail malpositioning with respect to the safety of the distal medio-lateral locking screws and the available options. Human cadaveric legs were plastinated according to the sequential plastination technique after intramedullary nailing of the tibia and were then cut transversely. The tibial nails were placed centrally or posteriorly. Macroscopic analysis showed a distinct drawback of posterior nail positioning, with diminished options for the placement of the locking screws and thereby a risk of damaging the anterior and posterior neuro-vascular bundles by distal medio-lateral locking screws.

Angle stable locking nails versus conventionally locked intramedullary nails in proximal tibial shaft fractures: a biomechanical study.

INTRODUCTION: A tibial nail with fixed-angle locking screws intends to combine the advantages of angular stability and intramedullary stabilization in extraarticular proximal tibial fractures. The goal of this study is to analyze if the angle stable tibial nail (ASN) is biomechanically more stable than an established conventional standard nail (CN). METHODS: Two types of nails were compared on a series of ten matched pairs of human tibiae. After setting a proximal tibial defect fracture, the intramedullary stabilized tibiae were axially loaded starting from 100 N increasing in steps of 100 N after every 200 cycles until failure was reached. Failure was defined as deformation of the fracture gap, fracturing of the bone or the implant. RESULTS: The two types of nails showed no significant difference in terms of maximum tolerated load, maximum cycles repeated or axial deformation of the bone-implant construct. The mean load at failure was 1,365 N for the CN and 1,195 N for the ASN. The mean axial deformation for conventional (19 mm) and angle stable nail (21 mm) did not differ significantly. Slightly less nail or screw loosening was noticed with the fixed-angle nail. CONCLUSION: No significant difference in stability between the two compared implants could be demonstrated. A trend could be shown indicating that the rate of nail loosening in the proximal osteotomized part of the bone was lower for the angle stable nail. This trend, however, could not be substantiated statistically.

Biomechanical stability of different suture fixation techniques for tibial eminence fractures.

PURPOSE: Displaced tibial eminence fractures require surgical fixation in order to obtain a stable knee joint. Suture fixation with FiberWire(®) seems to be the most favorable therapeutic option. Biomechanical studies show failure of this technique most commonly due to a suture cutout with subsequent fracture of the tibial eminence fragment. The goal of this study is to compare the biomechanical properties of three different techniques of suture fixation using FiberWire(®). METHODS: Bone mineral density was evaluated in 18 human knee specimens by pqCT, and three similar groups were formed. A standardized anterior tibial eminence fracture was created, and suture fixation was performed using one of three different techniques in 6 specimens each. Cyclic and destructive testing was conducted. RESULTS: Significant differences between the three techniques could be shown neither in the cycles needed to achieve a steady state nor in a failure load or initial stiffness. Almost all specimens failed by suture cutout. CONCLUSION: The presented modification of the existing technique for suture fixation of tibial eminence fractures did not lead to an increased initial stability nor did it lower the rate of suture cutout. All tested suture techniques showed comparable initial stiffness and failure load.

Relationship between human femorotibial joint configuration and the morphometry of the anterior cruciate ligament.

INTRODUCTION: Individual variations in the anatomy of the knee joint have been suggested to affect the ability to functionally compensate for ACL insufficiency or to put an individual at an increased risk of ACL injury. These variations include the posterior tibial slope, the concavity of the medial tibial plateau, the convexity of the lateral tibial plateau, and the configuration of the femoral condyles. METHOD: This anatomical study investigates if there is a correlation between the individual surface geometry of the femorotibial joint and the morphometry of the ACL. These data were assumed to provide evidence whether or not the functional stability of an ACL-insufficient knee may be derived from its radiographic surface geometry. Standardised measurement techniques were used to analyse the surface geometry of 68 human cadaver knees. Data were correlated with the cross-sectional area, the area of insertion and position of the footprint of the ACL and its functional bundles. RESULTS: Analysis revealed that there was a significant, but weak correlation between the femoral and tibial area of ACL insertion and the depth of the medial and lateral femoral condyle. No correlation was found between the surface geometry of the femorotibial joint and the cross-sectional area of the ACL. The results of this anatomical study suggest that the relationship between the joint surfaces and the morphometry of the ACL primarily is a function of size of the knee joint. CONCLUSIONS: Based on our results, there is no evidence that the stability of the knee can be derived from its radiographic surface geometry.

Relationships of the lateral femoral cutaneous nerve to bony landmarks.

BACKGROUND: The lateral femoral cutaneous nerve (LFCN) can be at risk during, for example, the insertion of pins in the anterior superior iliac spine (ASIS) during external fixation of the pelvis, total hip arthroplasty through a direct anterior approach, open surgery for impingement in the hip through an anterior approach, and periacetabular osteotomy. During surgery, the surgeon usually assumes the location of the LFCN by using the ASIS as a landmark. QUESTIONS/PURPOSES: We investigated (1) whether there is any relationship between the LFCN and the ASIS and (2) the anatomy of the LFCN at the lateral border of the psoas major. METHODS: Using 25 formalin-fixed cadavers, we determined the location of the LFCN emergence point as above, same level with, or below the iliac crest (IC). We measured the distances between the LFCN emergence point and the crossing of the IC and psoas major, ASIS, and pubic tubercle. We measured the distances between the ASIS and pubic tubercle (AB) and the ASIS and the point where the LFCN crossed the inguinal ligament (AC) and then calculated AC/AB. RESULTS: The LFCN was below the IC on 19 sides, at the same level on 13 sides, and above on 12 sides. The distances were -0.98 ± 5.57 cm to the IC, 12.39 ± 2.67 cm to the ASIS, and 17.76 ± 3.33 cm to the pubic tubercle. AB was 13.11 ± 1.08 cm, AC 2.95 ± 2.01 cm, and AC/AB 0.22 ± 0.16. CONCLUSIONS/CLINICAL RELEVANCE: The LFCN may emerge from the lateral border of the psoas major above or below the IC. The AC/AB ratio can help surgeons to find the LFCN in patients with different body types.

Morphometric and biomechanical comparison of tendons used for interposition arthroplasty in carpometacarpal arthritis of the thumb.

PURPOSE: To identify the wrist tendon most effectively maintaining the trapezial space in interpositional arthroplasty in osteoarthritis of the carpometacarpal joint of the thumb. METHODS: The morphometrics of the os trapezium and the tendons of the flexor carpi radialis, extensor carpi radialis longus, and abductor pollicis longus were determined. The stiffness and compressive loading characteristics of the rolled-up tendons were compared to the os trapezium. RESULTS: No significant morphometric differences between the three tendons were found. The mass and volume of the trapezium was significantly larger when compared to the tendon balls. No significant differences in the compressive loading resistance were found between the tendons, but the mean stiffness was 85% lower when compared to the os trapezium. CONCLUSIONS: Neither tendon material approached the volume nor the stiffness provided by the os trapezium. Any tendon is considered to insufficiently maintain the trapezial space following trapeziectomy.

Do locked compression intramedullary nails improve the biomechanical stability of distal femoral fractures?

BACKGROUND: A distal femur nail with fixed-angle locking screws intends to combine the advantages of angular stability and intramedullary stabilization in extraarticular distal femur fractures. The goal of this study was to analyze whether the locked compression distal femur nail (LCN) was biomechanically more stable than a conventional standard distal femur nail (CN). METHODS: Both nails were compared on a series of 10 matched pairs of human femora. After setting a distal femur defect fracture, the intramedullary stabilized femur was axially loaded starting from 100 N, increasing in steps of 100 N after every 200 cycles with a triangular frequency of 1 Hz, until a predefined point of failure was reached. RESULTS: The two types of nails showed no significant difference in terms of maximum tolerated load, maximum number of cycles repeated, or axial deformation of the bone-implant construct. The mean load at failure was 2,954 N for the CN and 2,483 N for the LCN. The mean axial deformation for the conventional (14.8 mm) and locked compression nail (15.3 mm) did not differ significantly. Mode of failure was a bony fracture in all specimens predominantly involving the proximal femur. CONCLUSIONS: No significant difference in stability between the two compared implants could be demonstrated. The LCN showed comparable characteristics under cyclic axial loading as the conventional distal femur nail. No migration into the articular space or implant failure was observed.

Effects of impaction on cement mantle and trabecular bone in hip resurfacing.

INTRODUCTION: Failures involving the femoral part in hip resurfacing remain problematic in terms of overall implant survival. In this context, effects of impaction strength on cement mantle morphology and trabecular bone damage have not been studied to date. MATERIALS AND METHODS: Sixteen paired cadaveric femora that had undergone hard and gently impacted hip resurfacing using a manual packing cementing technique in a previous study, were evaluated morphologically. The earlier study had revealed lower failure loads for hard impacted heads. A central slice of each femoral head underwent microradiography. RESULTS: Overall cement mantle thickness averaged 2.0 mm (range 0-5 mm) in the hard and in the low impact group with no significant difference between groups (p = 0.299). No signs of damage in the bone remnants inside the prosthesis of the fractured proximal femurs were detected in the microradiographic analysis. CONCLUSION: Cement mantle thickness was not influenced by impaction strength when using a manual packing cementing technique. No trabecular damage underneath the implant was detected despite lower failure loads, confirming the difficulty to identify small trabecular damage in an in vitro study.

Biomechanical assessment of suture techniques used for tendon repair.

OBJECTIVE: The aim of this study was to assess different tendon suture techniques from the perspectives of both tensile strength and early active mobilization. METHODS: In this study, we implemented repairs on 40 flexor digitorum profundus (FDP) tendons, acquired from fresh frozen cadavers. The tendons were divided into 5 groups of 8 tendons each. We applied the 2-strand modified Kessler suture technique in the first group, the 4-strand Strickland suture technique in the second group, the 4-strand modified Kessler (without epitenon suture) suture technique in the third group, and the 4-strand modified Kessler (with epitenon sutures) suture technique in the fourth group. The remaining 8 intact tendons were set aside as the control group. The strength of the different tendon suture techniques were measured using the Instron(®) device. RESULTS: The average tolerance strength of the first group was determined as 39.89 ± 9.65 Newtons (N), the average tolerance strength of the second group was 39.64 ± 9.14 N, the average tolerance strength of the third group was 50.29 ± 11.24 N, the average tolerance strength of the fourth group was 54.47 ± 6.83 N, and the average tolerance strength of the control group was 119 ± 17.59 N. The tensile strength of the fourth group was significantly higher (p<0.05) than the first group, and the tensile strength of the third group was also significantly higher (p<0.05) than the first group. No significant difference was observed between the tensile strengths of the second and first groups (p>0.05). CONCLUSION: According to our findings, the tensile strength of 4-strand sutures, with or without epitenon sutures, are significantly higher than the tensile strength of 2-strand sutures. All suture techniques applied had sufficient tensile strength to promote early mobilization.

[Imageless computer navigation of hip resurfacing arthroplasty]. / Bildfreie Computernavigation von Hüftoberflächenersatzprothesen.

OBJECTIVE: Precise implantation of hip resurfacing arthroplasty by imageless computer navigation. Hence a malalignment of the femoral component, leading to early loss of the implant, can safely be avoided. INDICATIONS: Coxarthrosis in patients with normal bone mineral density; only minor deformity of the femoral head that enables milling around the femoral neck without notching. CONTRAINDICATIONS: Osteoporosis; large necrosis of the femoral head; metal allergy; small acetabular seat and corresponding wide femoral neck, leading to needless acetabular bone loss; pregnancy, lactation. SURGICAL TECHNIQUE: Hip joint exposure by a standard surgical approach, bicortical placement of a Schanz screw for the navigation array in the lesser trochanter. Referencing of the epicondyles, the four planes around the femoral neck and head by use of the navigation pointer. Planning of the desired implant position on the touchscreen of the navigation device; a guide wire is inserted into the femoral head and neck using the navigated drill guide; navigated depth drilling is performed. The femoral head is milled using the standard instruments. The acetabular bone stock is prepared with the conventional instrumentation; high-viscosity cement is finger-packed on the reamed head and the femoral component is inserted. Hammer blows should be avoided to prevent microfractures. Verification of the implant position by the navigation device; displacement of the Schanz screw; joint reposition and closure of the wound. POSTOPERATIVE MANAGEMENT: Standard postoperative management after hip arthroplasty. RESULTS: The comparison of 40 navigated and 32 conventionally implanted ASR prostheses resulted in a significant reduction of outliers by use of computer navigation (navigated procedures: one outlier, conventional procedure: nine outliers; p<0.001). Accuracy of the navigation device was tested by analysis of planned and verified implant position: CCD angle accuracy was 1 degrees , antetorsion accuracy was 1 degrees , and offset accuracy was 1.5 mm. An ongoing computed tomography-based anatomic study proved a varus-valgus accuracy of the navigation device of 1 degrees .

Biomechanical properties of orthodontic miniscrews. An in-vitro study.

OBJECTIVE: Comparing five commercially-available miniscrew types for skeletal anchorage with regard to the biomechanical properties influencing their primary stability. MATERIAL AND METHODS: Included in this study was a total of 196 self-tapping and self-drilling miniscrews having a diameter of 2 mm (or the largest possible diameter of the manufacturer in question), a thread shaft length of 10 mm, or the longest miniscrew supplied by the manufacturers. The screw types tested were the FAMI 2, Orlus mini-implant, T.I.T.A.N. Pin, tomas-pin and Vector TAS. Insertion and loosening torque measurements, and pullout tests in axial (0 degrees), 20 degrees and 40 degrees directions, as well as test series with and without pilot hole drilling were performed. Bovine femoral heads having the same bone mineral density (BMD) were used as bone-testing material. RESULTS: Higher insertion torques were found for the cylindrical FAMI 2 screw, the conical Orlus mini-implant and the Vector TAS screw (with mean values of 39.2 Ncm, 32.1 Ncm and 49.5 Ncm) than for the cylindrical T.I.T.A.N. pin and tomas-pin. Insertion without predrilling led the insertion torques of all five screws to rise significantly. We noted statistically significant differences among the five screws in the pullout tests. Those highly significant differences at axial (0 degrees) and 20 degrees angles were not apparent at the 40 degrees pullout angle. Compared with the pullout forces (load) in the axial direction, the cylindrical screws' load values decreased markedly according to the angle (by up to -46.6%). The reduction in pullout force in conjunction with an increasing angle was much less pronounced in the conical screws (-0.8% to -29.0%). The tomas-pin demonstrated the highest pullout force and stiffness values throughout the tests. A total of five tomas-pins, two Orlus mini-implants and one FAMI 2 screw fractured during the pullout tests. CONCLUSIONS: Results from our insertion torque measurements suggest that a conical screw design will provide greater primary stability than cylindrical screw types. The cylindrical screw design's superiority was evident in the pullout tests. All the miniscrews' primary stability rose after drill-free insertion. The tomas-pin screws, although biomechanically superior to the other screws, were most prone to fracture.

The influence of talonavicular versus double arthrodesis on load dependent motion of the midtarsal joint.

BACKGROUND: Today the most frequently used operative procedures in advanced arthritis of the hindfoot joints are isolated talonavicular arthrodesis and double arthrodesis (involving the talonavicular and calcaneocuboid joints, i.e. the Chopart joint). This in vitro study investigates whether the fusion of the talonavicular joint alone can provide the hindfoot, as well as a midfoot, with comparable biomechanical stability as the double arthrodesis does. Hence with the less-invasive intervention the same benefit in terms of pain reduction and better functionality could be achieved. METHODS: In a series of ten fresh cadaver feet without any radiological pathologies, we measured the range of motion of different tarsal bones in three planes under axial stress. Every foot was loaded without arthrodesis, after talonavicular and after double arthrodesis, by charging tibia and fibula with a force of 350 N using a calibrated Instron® load frame. Each tarsal bone was marked with a K-wire and its motion was measured by registering the movement of the wire's shade that was projected onto the surrounding walls of the trial box. RESULTS: Both operative procedures led to a considerable reduction of the motion of every marked bone to a mean of 18% of the preoperative value. In direct comparison of the two simulated arthrodeses we found for every bone and in every plane only minimal differences of the mean excursions of 1.0 mm on average. Both fusions lead to equal residual tarsal bone motion postoperatively, and provide the midtarsal joint as well as the subtalar joint with comparable biomechanical stability. CONCLUSIONS: Isolated talonavicular arthrodesis is a useful and effective alternative to double arthrodesis. It is the less complicated, less-invasive and functionally equivalent operative option for arthritic alterations of the hindfoot and transverse tarsal joint.

Tension degradation of anterior cruciate ligament grafts with dynamic flexion-extension loading: a biomechanical model in porcine knees.

PURPOSE: This study investigates the influence of various femoral anterior cruciate ligament graft fixation methods on the amount of tension degradation and the initial fixation strength after cyclic flexion-extension loading in a porcine knee model. METHODS: One hundred twenty porcine digital extensor tendons, used as 4-stranded free tendon grafts, were fixated within porcine femoral bone tunnels by use of extracortical button, cross-pin, or interference screw fixation. One hundred twenty porcine patellar tendon-bone grafts were fixated by use of cross-pin, interference screw, or press-fit fixation. Each femur-graft complex was submitted to cyclic flexion-extension loading for 1,000 cycles throughout different loading ranges, and the total loss of tension was determined. After cyclic testing, the grafts were loaded to failure, and the data were compared with a pullout series without cyclic loading. RESULTS: Tension degradation after 1,000 cycles of flexion-extension loading averaged 62.6% +/- 10.0% in free tendon grafts and 48.9% +/- 13.35% in patellar tendon-bone grafts. There was no influence of the loading range on the total amount of tension degradation. The total amount of tension degradation was the highest with interference screw fixation of free tendon and patellar tendon-bone grafts. Despite excessive loss of tension, the initial fixation strength of the femur-graft complex was not reduced. CONCLUSIONS: The method of femoral graft fixation significantly influenced tension degradation during dynamic flexion-extension loading. Femoral graft fixation methods that secure the graft close to the tunnel entrance and that displace the graft substance from the center of the bone tunnel show the largest amount of tension degradation during cyclic flexion-extension loading. The graft substance, not the fixation site, was the weakest link of the graft complex within this investigation. CLINICAL RELEVANCE: We believe that the graft fixation method should be considered when aiming to improve the precision of femoral graft placement in anterior cruciate ligament reconstruction.

The anterior to midaxillary line between the 4th or 5th intercostal space (Buelau position) is safe for the use of thoracostomy tubes in preterm and term infants.

OBJECTIVES: Thoracostomy tubes are widely used in neonatology. Complications occurred significantly more frequently in infants, especially neonates, than in adults. Principally, the access is the modified Buelau position which takes place in the anterior axillary line at the 4th or 5th intercostal space above the margin of the ribs. AIM: This study seeks to determine the characteristics and topographic conditions of the anatomical structures at the ventral and lateral thoracic wall in the preterm and term neonate. BACKGROUND: Fifteen formalin-fixed stillborns were prepared (nine male, six female, 28-43 weeks gestational age). METHODS/MATERIALS: The anatomical preparation involved the complete thoracic wall region. RESULTS: In all preparations, a venous vessel was detected at the lateral wall and was identified as v. thoracoepigastrica without accompanying artery. Arteria (a.) and vena (v.) thoracica interna were regularly found close to the sternal plate on both sides between rib and fascia. With increasing gestational ages the course of the v. thoracoepigastrica varied significantly between the left and right thoracic wall. It was demonstrated that the v. thoracoepigastrica regularly arose within the abdominal or thoracic subcutaneous fat and drained into the v. subclavia. The variance between its course was almost 5-12 mm to the lateral or medial side. At both thoracic sides, no other organs or organ structures except lung parenchyma could be detected when using the Buelau position. CONCLUSIONS: The anterior to midaxillary line between the 4th or 5th intercostal space (Buelau position) is safe for the use of thoracostomy tubes in preterm and term infants.

Side differences in the anatomy of human knee joints.

Side-to-side comparison of anatomical or functional parameters in the evaluation of unilateral pathologies of the human knee joint is common practice, although the amount of symmetry is unknown. The aim of this study was to test the hypothesis that there are no significant differences in the morphometric knee joint dimensions between the right and the left knee of a human subject and that side differences within subjects are smaller than intersubject variability. In 20 pairs of human cadaver knees, the morphometry of the articulating osseous structures of the femorotibial joint, the cruciate ligaments, and the menisci were measured using established measurement methods. Data were analyzed for overall side differences and the ratio between within-subject side differences and intersubject variability was calculated. In three out of 71 morphometric dimensions there was a significant side difference, including the posterior tibial slope, the anatomical valgus alignment of the distal femur, and the position of the femoral insertion area of the ACL. In two additional parameters, including the cross-sectional area of the ACL and PCL, within-subject side differences were larger than intersubject variability. In general, there was a positive correlation in morphometric dimensions between right and left knees in one subject. It is concluded that a good correlation in the morphometric dimensions of a human knee joint exists between the right and the left side. This study supports the concepts of obtaining morphometric reference data from the contralateral uninjured side in the evaluation of unilateral pathologies of the knee joint.