HRTEM Analysis of the Influence of Non-stick Coal's Oxidation Degree on Aromatic Fringe Morphology.

The purpose of this research was to explore the parameters of the aromatics lattice fringes by using high resolution transmission electron microscopy (HRTEM) patterns, combined with ArcGIS and MATLAB methods, to quantitatively evaluate and analyze the coal samples oxidized by different concentrations of H2O2, and to explore the changes in the morphology and spatial distribution of the aromatic system under oxidation. As the degree of oxidation increased, the orientation of the aromatic lattice fringes became more disordered, and the distortion degree increased. The distribution range of Y and T type dislocation structures, which were widely distributed in short (<0.59 nm) lattice fringes, increased, while that of spiral type dislocation structures, which were distributed in medium (0.59-0.99 nm) and long (1.00-2.49 nm) lattice fringes, decreased. In addition, the collapse and condensation of aromatic slices caused by continuous oxidation further weakened the π-π stacking effect between aromatic rings, resulting in a decrease in the interlayer distance and stacking height. The advantages of HRTEM analysis were confirmed by XRD, SEM and FTIR analysis. This provides a new perspective on the oxidation phenomenon and enriches the examination of the low-temperature oxidation mechanism of coal.

The Molecular Model of Organic Matter in Coal-Measure Shale: Structure Construction and Evaluation Based on Experimental Characterization.

To investigate the molecular structure and micropore structure of organic matters in coal-measure shale, the black shale samples of the Shanxi formation were collected from Xishan Coalfield, Taiyuan, and a hybrid experimental-simulation method was used for realistic macromolecular models of organic matter (OM). Four experimental techniques were used to determine the structural information of OM, including elemental analysis, state 13C nuclear magnetic resonance (13CNMR), X-ray photoelectron spectroscopy (XPS), and Fourier transform infrared spectroscopy (FTIR). With structural parameters, two-dimensional (2D) average molecular models of OM were established as C177H160O8N2S with a molar weight of 2474, which agreed well with the experimental 13C-NMR spectra. A realistic three-dimensional (3D) OM macromolecular model was also reconstructed, containing 20 2D molecules with a density of 1.41 g/cm3. To determine the connectivity and spatial disposition of the OM pores, focused ion beam microscope (FIB-SEM) and transmission electron micrographs (TEM) were utilized. The 3D OM pores models were developed. The results show that whether the OM pores varied from 20 to 350 nm as obtained from FIB-SEM images or less than 10 nm as observed in the TEM images, both were of poor connectivity. However, the ultra-micro pores from the 3D OM macromolecular model varied from 3Å to 10 Å and showed certain connectivity, which may be the main channel of diffusion. Furthermore, with the pressure increased, the methane adsorption capacity of the 3D OM model increased with a maximum value of 103 cm3/g at 7 MPa, indicating that OM pores less than 1 nm have a huge methane adsorption capacity. Therefore, our work provides an analysis method that is a powerful and superior tool in further research on gas migration.

Molecular Mechanism Study on the Effect of Microstructural Differences of Octylphenol Polyoxyethylene Ether (OPEO) Surfactants on the Wettability of Anthracite.

Inhalable coal dust poses a serious threat to coal mining safety, air quality, and the health of miners. Therefore, the development of efficient dust suppressants is crucial for addressing this issue. This study evaluated the ability of three high-surface-active OPEO-type nonionic surfactants (OP4, OP9, and OP13) to improve the wetting properties of anthracite via extensive experiments and a molecular simulation and determined the micro-mechanism of different wetting properties. The surface tension results show that OP4 has the lowest surface tension (27.182 mN/m). Contact angle tests and wetting kinetics models suggest that OP4 exhibits the strongest wetting improvement ability on raw coal with the smallest contact angle (20.1°) and the fastest wetting rate. In addition, FTIR and XPS experimental results also reveal that OP4-treated coal surfaces introduce the most hydrophilic elements and groups. UV spectroscopy testing shows that OP4 has the highest adsorption capacity on the coal surface, reaching 133.45 mg/g. The surfactant is adsorbed on the surface and pores of anthracite, while the strong adsorption ability of OP4 results in the least amount of N2 adsorption (8.408 cm3/g) but the largest specific surface area (1.673 m2/g). In addition, the filling behavior and aggregation behavior of surfactants on the anthracite coal surface were observed using SEM. The MD simulation results indicate that OPEO reagents with overly long hydrophilic chains would produce spatial effects on the coal surface. Under the influence of the π-π interaction between the hydrophobic benzene ring and the coal surface, OPEO reagents with fewer ethylene oxide quantities are more prone to adsorb onto the coal surface. Therefore, after the adsorption of OP4, both the polarity and the water molecule adhesion ability of the coal surface are greatly enhanced, which helps to suppress dust production. These results provide important references and a foundation for future designs of efficient compound dust suppressant systems.