Baseplate inferior offset affects shoulder range of motion in reverse shoulder arthroplasty in Asian population.

BACKGROUND: Impingement is a common complication of reverse shoulder arthroplasty. Placement of the baseplate with a wide impingement-free angle is ideal; however, there are few studies on Asian populations, which have smaller height and physique, and there is a lack of guidance on achieving optimal outcomes. The purpose of the present study was to explore the impingement-free range of motion reverse shoulder arthroplasty and analyze the suitable baseplate position or tilt for the Asian population using simulation software. METHODS: We uploaded computed tomography scan data from 20 Asian patients to three-dimensional (3D) simulation software. The implantation of the reverse shoulder arthroplasty component was performed on the 3D humerus and scapula using software, and range of motion was assessed until impingement occurred. RESULTS: The range of motion in flexion significantly improved when the baseplate was lowered up to 3 mm inferiorly. Range of motion in abduction and internal and external rotation significantly improved as the baseplate was lowered up to 4 mm. There was no significant difference in range of motion in any motion after changing the inferior tilt, except in internal and external rotation. CONCLUSIONS: The range of motion in abduction, flexion, and internal and external rotations significantly improved with increased inferior offset. These results may prove valuable in determining the optimal baseplate position for RSA, particularly in Asian populations.

Reverse dynamics analysis of contact force and muscle activities during the golf swing after total hip arthroplasty.

There are no reports on hip kinetics including contact forces and muscle activities during the golf swing after total hip arthroplasty (THA). The aim of this study was to identify the characteristics of three-dimensional dynamics during the golf swing. Ten unilateral primary THA patients participated in motion capture test of their driver golf swing. The driver swing produced approximately 20-30° of rotation in both lead and trail replaced hips. The mean hip contact forces (HCFs) of lead and trail replaced hips were 5.1 and 6.6 × body weight, respectively. Left and right THAs showed similar HCFs of lead and trail hips. More than 60% of the Percent maximum voluntary isometric contraction was found in bilateral iliopsoas muscles in all unilateral THA. Three factors [female sex, lower modified Harris Hip Score, and higher HCF of surgical side] were associated with the golf-related replacement hip pain. Golf is an admissible sport after THA because driver swings do not contribute excessive rotation or contact forces to hip prostheses. HCF could be reduced through swing adjustments, which may allow patients with golf-related replacement hip pain to develop a comfortable golf game free from pain.

Prevalence and predisposing factors of neuropathic pain in patients with rotator cuff tears.

BACKGROUND: The management of pain in patients with rotator cuff tears can be challenging. Neuropathic pain is reportedly associated with pain occurrence in musculoskeletal diseases. However, to date, few studies have reported on the prevalence of neuropathic pain in patients with rotator cuff tears or identified the factors associated with neuropathic pain in a multicenter study. METHODS: A total of 391 patients (205 males and 186 females; median age, 67.7 years; range, 27-92 years) with rotator cuff tears were included in this study. The prevalence of neuropathic pain in rotator cuff tears was investigated using the Japanese version of the painDETECT questionnaire for all patients. In addition, factors significantly associated with the occurrence of neuropathic pain were examined using multivariate logistic regression analysis. RESULTS: Twenty-eight patients (7.2%) were classified into the neuropathic pain group (score ≥19), 97 (24.8%) into the uncertainty regarding neuropathy group (score 13-18), and 266 (68.0%) into the nociceptive pain group (score ≤12). According to the multivariate logistic regression analysis, the independent predictors of neuropathic pain were the VAS score (most severe pain during the past 4 weeks; odds ratio, 1.55; 95% confidence interval [CI], 1.23-2.09) and UCLA shoulder score (odds ratio, 0.81; 95% CI, 0.65-0.97). CONCLUSIONS: Based on the study findings, the prevalence of neuropathic pain in patients with rotator cuff tear was 7.2%. It is important to investigate the presence or absence of neuropathic pain when treating patients with painful rotator cuff tears, because neuropathy associated with rotator cuff tears may adversely affect patient outcomes.

Steroid-induced osteonecrosis of the humeral head in a 20-year-old man treated with an osteochondral autograft: A case report.

To our knowledge, only one previous report described the treatment of osteochondral autograft for steroid-induced osteonecrosis of the humeral head (ONHH) in a middle-aged patient. The present report describes a 20-year-old man who was found to have avascular osteonecrosis of the right humeral head after corticosteroid pulse treatment, followed by oral corticosteroid therapy. The patient complained of serious right shoulder pain and limited range of motion (ROM). Anteroposterior (AP) radiographs of the right shoulder revealed a crescent sign at the humeral head, indicating subchondral bone collapse with a linear sclerotic change and normal articular surface of the glenoid. The case was categorized as Stage 3 according to the Cruess classification. In general, Cruess classification Stage 3 is treated with humeral head replacement and shoulder arthroplasty. The patient underwent surgical treatment involving osteochondral autograft transplantation. Autografts were harvested from the right knee. At the 1.5-year follow-up, the patient was pain-free and showed an improved active ROM. Furthermore, AP radiographs demonstrated that the glenohumeral joint space was maintained, and no progression of humeral head collapse was observed. This case may be helpful in decision-making if young patients with ONHH require surgical treatment. Furthermore, osteochondral autograft transplantation may be an effective treatment for ONHH.

Biomechanical Comparison of a Horizontal Mattress, Cross Suture and Vertical Mattress for Repair of a Tendon Weave in a Porcine Model.

Background: An effective suture method enables early active motion exercises and optimal post-surgical outcomes. The aim of this study is to evaluate the tensile strength of three suture configurations - horizontal mattress (HM), vertical mattress (VM) and a cross suture for repair of a tendon weave. We hypothesised that the direction of mattress sutures relative to the tendon fibres would affect the tensile strength of tendon repair. Methods: Using porcine flexor tendons and the same number of surgical sutures, three tendon weave constructs differing in the method of suture were compared: HM suture configuration (conventional technique), cross-stitch (CS) configuration (conventional technique) and VM suture configuration (novel technique). Ten pairs of each group were mounted in a material testing machine and subjected to a simple tensile test and a cyclic loading test for their biomechanical comparison. Results: The VM group and CS group had significantly higher ultimate failure load, linear stiffness and fatigue strength as compared to the HM group. The failure mode was suture breakage or tendon rupture for the VM and the CS group, while the suture pullout of the tendon only occurred in the HM group. Conclusion: Among the three techniques used for repair of a tendon weave, the VM suture technique was demonstrated to have the greatest tensile strength and least associated with suture pull-out. The direction of the mattress suture in relation the direction of tendon fibres affects the strength of repair.

Risk of penetration of the baseplate peg in reverse total shoulder arthroplasty for an Asian population.

PURPOSE: Baseplate positioning may affect clinical outcome after reverse total shoulder arthroplasty (RTSA). The aim of this study was to evaluate the risk of penetration of the baseplate peg in RTSA. METHODS: Forty-four patients with rotator cuff arthropathy or massive rotator cuff tears were included. Using their computed tomography data, ten insertion patterns of the baseplate pegs were simulated. First, in the axial plane, the baseplate was placed perpendicular to the Friedman axis (Friedman placement) and parallel to the glenoid surface (glenoid placement). Second, each of these placements were classified into the following groups: The baseplate peg was placed 2 mm anterior to the long axis of the glenoid (group A2), 1 mm anterior (group A1), on the long axis (group C0), 1 mm posterior (group P1), and 2 mm posterior (group P2). Cases in which the baseplate peg was within the scapular neck were defined as non-penetration, and the non-penetration rates among each group were evaluated and compared between sexes, and their relationship with patient height was evaluated. RESULTS: In both the Friedman and glenoid placements, the non-penetration rate was significantly higher in groups A2 (68.2% and 70.5%) and A1 (65.9% and 65.9%) compared with groups P1 (18.2% and 29.5%) and P2 (9.1% and 13.6%; p < 0.001) and in males than in females (p < 0.05). Furthermore, the non-penetration rate tended to be higher as the patient's height increased. CONCLUSIONS: It is recommended that the baseplate peg be placed anterior to the long axis of the glenoid.

Stump classification was correlated with retear in the suture-bridge and double-row repair techniques for arthroscopic rotator cuff repair.

PURPOSE: The Stump classification is significantly correlated with a retear after arthroscopic rotator cuff repair. However, no study has evaluated whether or not the stump classification is correlated with retear in the suture-bridge or double-row repair techniques. The aim of this study was to evaluate the relationship between a retear and the stump classification in the suture-bridge and double-row repair techniques. METHODS: Among 389 patients who underwent arthroscopic repairs of full-thickness rotator cuff tears using suture-bridge or double-row repair techniques, 326 patients (median age 67.0 years; range 25-85) were included. There were 51 small, 172 medium, 83 large, and 20 massive tears. Two hundred forty patients were treated with the suture-bridge technique, and 86 patients were treated with the double-row technique. The following variables were analyzed: age, sex, the Cofield classification, anteroposterior and mediolateral tear size on preoperative MRI, global fatty degeneration index, and the stump classification. Cuff integrity was evaluated on magnetic resonance imaging at 6 months after surgery. The patients were divided into the intact and retear groups and the relationship between the variables and retear was evaluated by multivariate logistic regression analysis. RESULTS: The overall retear rate was 10.1%. In the multivariate logistic regression analysis, the independent predictors of a retear were the stump classification type 3 (Odds ratio: 4.71, p = 0.0246), global fatty degeneration index (Odds ratio: 3.87, p = 0.0030), and anteroposterior tear size (Odds ratio: 1.07, p = 0.0077) in the suture bridge technique. In the double-row technique, the independent predictors of retear were stump classification type 3 (Odds ratio: 7.82, p = 0.0348), and age (Odds ratio: 1.22, p = 0.0163). CONCLUSION: The stump classification was significantly correlated with retear in the suture-bridge and double-row repair technique. Stump classification type 3 was indicated to be an important risk factor for predicting retear. LEVEL OF EVIDENCE: III.

Dynamic scapulohumeral rhythm: Comparison between healthy shoulders and those with large or massive rotator cuff tear.

INTRODUCTION: Assessment of scapular kinematics and the dynamics of the scapulohumeral rhythm (SHR) would be important for understanding pathologies of the shoulder and to inform treatment. Our aim in this study was to evaluate the SHR and scapular kinematics in patients with a rotator cuff tear (RCT), compared to a control group with healthy shoulders using image-matching techniques. MATERIALS AND METHODS: The shoulder kinematics of large or massive RCT patients were evaluated and compared to a control group with healthy shoulders. Radiographic surveillance was performed throughout the full range of external rotation and scapular plane abduction. Computed tomography imaging of the shoulder complex was performed, with three-dimensional image reconstruction and matching to the radiographs to measure three-dimensional positions and orientations. SHR and angular values of the scapula were measured. RESULTS: Scapular external rotation in the late phase of external rotation movement was greater in the RCT group than in the control group (p < 0.05), but with no difference in the SHR. During scapular plane abduction, there were significant differences in SHR, scapular posterior tilt and scapular upward rotation between the RCT and control group (p < 0.05). CONCLUSIONS: Regarding clinical relevance, this study clarified the differences of SHR and angular values of the scapula between the RCT and control group. These results underline the importance of assessment the SHR and scapular kinematics in individuals with a RCT. RCT is associated with specific compensation in the kinematics of the scapula and SHR during external rotation and scapular plane abduction, which could inform treatment.

Biomechanical analysis of four different medial row configurations of suture bridge rotator cuff repair.

BACKGROUND: Rotator cuff tendon rupture after suture bridge repair occasionally occurs at the medial row, with remnant tendon tissue remaining at the footprint. While concentrated medial row stress is suspected to be involved in such tears, the optimal suture bridge technique remains controversial. METHODS: This study aimed to investigate the construct strength provided by suture bridge techniques having four different medial row configurations using artificial materials (n = 10 per group): Group 1, four-hole (two stitches per hole) knotless suture bridge; Group 2, eight-hole (one stitch per hole) parallel knotless suture bridge; Group 3, eight-hole non-parallel knotless suture bridge; and Group 4, eight-hole knot-tying suture bridge. Each construct underwent cyclic loading from 5 to 30 N for 20 cycles, followed by tensile testing to failure. The ultimate failure load and linear stiffness were measured. FINDINGS: Group 2 had the highest ultimate failure load (mean 160.54 N, SD 6.40) [Group 4 (mean 150.21 N, SD 9.76, p = 0.0138), Group 3 (mean 138.80 N, SD 7.18, p < 0.0001), and Group 1 (mean 129.35 N, SD 4.25, p < 0.0001)]. The linear stiffness of Group 2 (mean 9.32 N/mm, SD 0.25) and Group 4 (mean 9.72 N/mm, SD 0.40) was significantly higher (p = 0.0032) than that of Group 1 (mean 8.44 N/mm, SD 0.29) and Group 3 (mean 8.61 N/mm, SD 0.31). INTERPRETATION: In conclusion, increasing the number of suture-passed holes, arranging the holes in parallel, and a knotless technique improved the failure load following suture bridge repair.

Histological evaluation of tendon formation using a scaffold-free three-dimensional-bioprinted construct of human dermal fibroblasts under in vitro static tensile culture.

INTRODUCTION: Tendon tissue engineering requires scaffold-free techniques for safe and long-term clinical applications and to explore alternative cell sources to tenocytes. Therefore, we histologically assessed tendon formation in a scaffold-free Bio-three-dimensional (3D) construct developed from normal human dermal fibroblasts (NHDFs) using our Bio-3D printer system under tensile culture in vitro. METHODS: Scaffold-free ring-like tissues were constructed from 120 multicellular spheroids comprising NHDFs using a bio-3D printer. Ring-like tissues were cultured in vitro under static tensile-loading with or without in-house tensile devices (tension-loaded and tension-free groups), with increases in tensile strength applied weekly to the tensile-loaded group. After a 4 or 8-week culture on the device, we evaluated histological findings according to tendon-maturing score and immunohistological findings of the middle portion of the tissues for both groups (n = 4, respectively). RESULTS: Histology of the tension-loaded group revealed longitudinally aligned collagen fibers with increased collagen deposition and spindle-shaped cells with prolonged culture. By contrast, the tension-free group showed no organized cell arrangement or collagen fiber structure. Additionally, the tension-loaded group showed a significantly improved tendon-maturing score as compared with that for the tension-free group at week 8. Moreover, immunohistochemistry revealed tenascin C distribution with a parallel arrangement in the tensile-loading direction at week 8 in the tension-loaded group, which exhibited stronger scleraxis-staining intensity than that observed in the tension-free group at weeks 4 and 8. CONCLUSIONS: The NHDF-generated scaffold-free Bio-3D construct underwent remodeling and formed tendon-like structures under tensile culture in vitro.

Evaluation of humeral head cartilage using magnetic resonance imaging T1 rho mapping for patients with small-to-medium rotator cuff tears: A pilot study.

BACKGROUND: It is unclear whether smaller rotator cuff tears cause cartilage degeneration. This study was designed to detect early humeral head cartilage degeneration in patients with small-to-medium cuff tears using magnetic-resonance-imaging T1 rho mapping. METHODS: Five male and 5 female volunteers without shoulder symptoms (control group) and 5 male and 5 female patients with small-to-medium (<3 cm) rotator cuff tears underwent 3.0-T magnetic resonance imaging of a single shoulder. T1 rho values of the humeral head cartilage were measured and analyzed. RESULTS: The total mean T1 rho value was 40.4 ± 3.4 ms for the control group and 45.0 ± 5.3 ms for the patient group. In the control group, the T1 rho values in the inferior articular cartilage were significantly higher than those in the superior and middle articular cartilage. In the patient group, there was no significant difference between all regions. A comparison between the patient and control groups showed that the mean T1 rho values in the superior-to-middle articular cartilage were significantly higher for the patient group than for the control group. However, in the inferior articular cartilage, there was no significant difference between both groups. CONCLUSIONS: This study showed the possibility of early cartilage degenerative changes in the superior-to-middle humeral head articular cartilage of patients with small-to-medium rotator cuff tears.

In vivo dynamic acromiohumeral distance in shoulders with rotator cuff tears.

BACKGROUND: There are no previous studies on the acromiohumeral distance in shoulders with large-to-massive full-thickness rotator cuff tears. In this study, the acromiohumeral distance in rotator cuff tear and healthy shoulders was measured using 3D-to-2D model-to-image registration techniques. METHODS: The dynamic glenohumeral kinematics during scapular plane abduction and axial rotation were analyzed in 11 rotator cuff tear patients and 10 healthy control subjects. Periodic radiographic images of scapular plane abduction and axial rotation were taken using a flat-panel radiograph image detector. Movements of the shoulder joint were assessed using radiographic images and computed tomography-derived digitally reconstructed radiographs. The acromiohumeral distance was defined as the shortest 3D distance between the acromion and the proximal humerus. FINDINGS: For scapular plane abduction, the rotator cuff tear group had significantly smaller acromiohumeral distance than the control group at 15°, 30°, 45°, 60°, 75°, 135°, and 150° of humeral abduction (P < 0.05 at each measured angle). For axial rotation in the adducted position, the rotator cuff tear group had significantly smaller acromiohumeral distance than the control group at each point between -20° and 40° of glenohumeral external rotation (P < 0.05 at each measured angle). INTERPRETATION: The minimum measured acromiohumeral distance was 0.9 mm in the rotator cuff tear shoulders and 2.1 mm in the healthy shoulders at 90° of scapular plane abduction. The findings are of clinical relevance because quantitative evaluation of the dynamic acromiohumeral distances in rotator cuff tear and healthy shoulders might provide important insight into subacromial impingement.

Dynamic kinematics of the glenohumeral joint in shoulders with rotator cuff tears.

BACKGROUND: No clear trend has emerged from the literature regarding three-dimensional (3D) translations of the humerus relative to the scapula in shoulders with rotator cuff tears (RCTs). The purpose of this study was to evaluate the kinematics of RCT shoulders using 3D-to-two-dimensional (2D) model-to-image registration techniques. METHODS: Dynamic glenohumeral kinematics during scapular plane abduction and axial rotation were analyzed in 11 RCT patients and 10 healthy control subjects. We measured the 3D kinematic parameters of glenohumeral joints using X-ray images and CT-derived digitally reconstructed radiographs. RESULTS: For scapular plane abduction, the humeral head center was positioned significantly more medially in shoulders with RCTs than in controls at 135° of humeral abduction (p = 0.02; RCTs versus controls: - 0.9 ± 1.6 versus 0.3 ± 1.3 mm). There was no significant difference in the superior/inferior translation of the humeral head center (p = 0.99). For axial rotation in adducted position, the humeral head center was positioned significantly more anteriorly in shoulders with RCTs than in controls at - 30° of glenohumeral external rotation (p < 0.0001; RCTs versus controls: 3.0 ± 1.7 versus 0.3 ± 1.5 mm). CONCLUSIONS: This study revealed the kinematics of shoulders with large to massive full-thickness RCTs: the humeral head center showed a medial shift at the late phase of scapular plane full abduction, and an anterior shift at the internal rotation position during full axial rotation. The kinematic data in this study, which describe the patterns of movement of shoulders with large to massive full-thickness RCTs, provide valuable information for future studies investigating glenohumeral translations in other pathological conditions of the shoulder. For clinical relevance, quantitative assessment of the dynamic kinematics of shoulders with RCTs might be a therapeutic indicator for achieving functional restoration.

A Biomechanical Comparison Between Asymmetric Pennington Technique and Conventional Core Suture Techniques: 6-Strand Flexor Tendon Repair.

PURPOSE: To evaluate the fatigue strength and gap sizes of the asymmetric Pennington technique compared with 2 conventional 6-strand core suture techniques: the triple-looped suture and the Yoshizu #1. METHODS: We recorded the fatigue strength (forces × cycles) and gap sizes of a 6-strand flexor tendon repair with different core suture techniques under cyclic loading in 30 porcine tendons. The asymmetric Pennington technique was performed with a Pennington repair of equal suture purchase in the 2 tendon stumps, with the 2 other Pennington repairs shifted by 3 mm, respectively, along the longitudinal axis of the tendon in relation to the first Pennington repair. The triple-looped suture technique was made with triple Tsuge sutures. The Yoshizu #1 technique was performed with a combined Pennington repair (using a double strand) and Tsuge suture. RESULTS: The asymmetric Pennington technique showed significantly greater fatigue strength and significantly smaller gaps in comparison to the triple-looped suture and Yoshizu #1 techniques. CONCLUSIONS: This study demonstrated that the asymmetric Pennington technique generated increased fatigue strength and reduced gap sizes compared with 2 conventional 6-strand core suture techniques, the triple-looped suture and Yoshizu #1. CLINICAL RELEVANCE: The asymmetric Pennington technique may permit an early active motion rehabilitation protocol similar to the triple-looped suture and Yoshizu #1 techniques.

Effect of the Optimal Asymmetry on the Strength of Six-Strand Tendon Repair: An Ex Vivo Biomechanical Study.

PURPOSE: To evaluate the mechanical properties of a 6-strand core suture repair with asymmetric purchase in the 2 tendon ends, in comparison with a repair with symmetric suture purchases. METHODS: Under cyclic loading of the tendons, we recorded the fatigue strength (Forces × Cycles) of a 6-strand flexor tendon repair with different symmetry in the lengths of suture purchase in 60 porcine tendons. The symmetric repair was made with 3 groups of parallel Kessler repairs of equal suture purchase (10 mm from the cut end) in the 2 tendon stumps. The asymmetric core suture repairs were then made with a Kessler repair of equal suture purchase (10 mm from the cut end) in the 2 tendon stumps, and shifting 2 other Kessler repairs by 1, 2, 3, 4, or 5 mm, respectively, along the longitudinal axis of the tendon in relation to the first (symmetric) Kessler repair. RESULTS: The core repairs with 2 mm or more asymmetry in suture purchases in 2 tendon ends showed significantly greater fatigue strength compared with those with symmetric suture placement. The core repairs with 3 mm or more asymmetry in suture purchases in 2 tendon ends showed significantly smaller gaps compared with those with symmetric suture placement. CONCLUSIONS: The core repairs with 3 mm or more asymmetry in suture purchases in 2 tendon ends generated increased fatigue strength and reduced gap sizes compared with those with symmetric suture placement in an ex vivo porcine model. CLINICAL RELEVANCE: An asymmetric core suture repair with 3 mm or more difference in purchase length may allow for earlier rehabilitation and reduce the risk of postoperative complications.

In vivo kinematic analysis of the glenohumeral joint during dynamic full axial rotation and scapular plane full abduction in healthy shoulders.

PURPOSE: The purpose of this study was to evaluate the kinematics of healthy shoulders during dynamic full axial rotation and scapular plane full abduction using three-dimensional (3D)-to-two-dimensional (2D) model-to-image registration techniques. METHODS: Dynamic glenohumeral kinematics during axial rotation and scapular plane abduction were analysed in 10 healthy participants. Continuous radiographic images of axial rotation and scapular plane abduction were taken using a flat panel radiographic detector. The participants received a computed tomography scan to generate virtual digitally reconstructed radiographs. The density-based digitally reconstructed radiographs were then compared with the serial radiographic images acquired using image correlations. These 3D-to-2D model-to-image registration techniques determined the 3D positions and orientations of the humerus and scapula during dynamic full axial rotation and scapular plane full abduction. RESULTS: The humeral head centre translated an average of 2.5 ± 3.1 mm posteriorly, and 1.4 ± 1.0 mm superiorly in the early phase, then an average of 2.0 ± 0.8 mm inferiorly in the late phase during external rotation motion. The glenohumeral external rotation angle had a significant effect on the anterior/posterior (A/P) and superior/inferior (S/I) translation of the humeral head centre (both p < 0.05). 33.6 ± 15.6° of glenohumeral external rotation occurred during scapular plane abduction. The humeral head centre translated an average of 0.6 ± 0.9 mm superiorly in the early phase, then 1.7 ± 2.6 mm inferiorly in the late phase, and translated an average of 0.4 ± 0.5 mm medially in the early phase, then 1.6 ± 1.0 mm laterally in the late phase during scapular plane abduction. The humeral abduction angle had a significant effect on the S/I and lateral/medial (L/M) translation of the humeral head centre (both p < 0.05). CONCLUSION: This study investigated 3D translations of the humerus relative to the scapula: during scapular plane full abduction, the humerus rotated 33.6° externally relative to the scapula, and during external rotation motion in the adducted position, the humeral head centre translated an average of 2.5 mm posteriorly. Kinematic data will provide important insights into evaluating the kinematics of pathological shoulders. For clinical relevance, quantitative assessment of dynamic healthy shoulder kinematics might be a physiological indicator for the assessment of pathological shoulders.

Direct reduction may need to be considered to avoid postoperative subtype P in patients with an unstable trochanteric fracture: a retrospective study using a multivariate analysis.

INTRODUCTION: It has recently been reported that the cases with an anterior femoral neck cortex posterior to the distal fragment (subtype P) in the lateral view of a postoperative radiograph have a risk of excessive sliding of lag screws compared to those located anterior to the distal fragment (subtype A) or perfectly continuous to the distal fragment (subtype N) following osteosynthesis for the treatment of a trochanteric fracture. The purpose of this study was to investigate factors that influence the postoperative subtype in the lateral view of radiographs. PATIENTS AND METHODS: This study reviewed 136 patients who underwent osteosynthesis using an intramedullary hip nail for the treatment of a trochanteric fracture. A closed reduction was performed in 130 patients (95.6 %), while a direct reduction via a small elevator with a small skin incision was performed in the other six patients (4.4 %). The 136 patients were divided into two groups (subtype P and subtype A or N) based on postoperative radiographs taken of the lateral view. Both clinical and radiological factors were analyzed using the univariate and multivariable analyses. RESULTS: Thirty-nine patients (29 %) were categorized as subtype P and 97 patients (71 %) were categorized as subtype A or N. A multivariate analysis demonstrated that unstable fractures were associated with a significant risk of postoperative subtype P (Odds ratio: 24.45, P = 0.0024). CONCLUSIONS: The results of this study suggest that direct reduction via a small elevator with a small skin incision or percutaneous intrafocal pinning may be needed in these cases.