Water-stable zirconium-based metal-organic framework material with high-surface area and gas-storage capacities.

We designed, synthesized, and characterized a new Zr-based metal-organic framework material, NU-1100, with a pore volume of 1.53 ccg(-1) and Brunauer-Emmett-Teller (BET) surface area of 4020 m(2) g(-1) ; to our knowledge, currently the highest published for Zr-based MOFs. CH4 /CO2 /H2 adsorption isotherms were obtained over a broad range of pressures and temperatures and are in excellent agreement with the computational predictions. The total hydrogen adsorption at 65 bar and 77 K is 0.092 g g(-1) , which corresponds to 43 g L(-1) . The volumetric and gravimetric methane-storage capacities at 65 bar and 298 K are approximately 180 vSTP /v and 0.27 g g(-1) , respectively.

Defect creation by linker fragmentation in metal-organic frameworks and its effects on gas uptake properties.

We successfully demonstrate an approach based on linker fragmentation to create defects and tune the pore volumes and surface areas of two metal-organic frameworks, NU-125 and HKUST-1, both of which feature copper paddlewheel nodes. Depending on the linker fragment composition, the defect can be either a vacant site or a functional group that the original linker does not have. In the first case, we show that both surface area and pore volume increase, while in the second case they decrease. The effect of defects on the high-pressure gas uptake is also studied over a large temperature and pressure range for different gases. We found that despite an increase in pore volume and surface area in structures with vacant sites, the absolute adsorption for methane decreases for HKUST-1 and slightly increases for NU-125. However, the working capacity (deliverable amount between 65 and 5 bar) in both cases remains similar to parent frameworks due to lower uptakes at low pressures. In the case of NU-125, the effect of defects became more pronounced at lower temperatures, reflecting the greater surface areas and pore volumes of the altered forms.

Unusual and highly tunable missing-linker defects in zirconium metal-organic framework UiO-66 and their important effects on gas adsorption.

UiO-66 is a highly important prototypical zirconium metal-organic framework (MOF) compound because of its excellent stabilities not typically found in common porous MOFs. In its perfect crystal structure, each Zr metal center is fully coordinated by 12 organic linkers to form a highly connected framework. Using high-resolution neutron power diffraction technique, we found the first direct structural evidence showing that real UiO-66 material contains significant amount of missing-linker defects, an unusual phenomenon for MOFs. The concentration of the missing-linker defects is surprisingly high, ∼10% in our sample, effectively reducing the framework connection from 12 to ∼11. We show that by varying the concentration of the acetic acid modulator and the synthesis time, the linker vacancies can be tuned systematically, leading to dramatically enhanced porosity. We obtained samples with pore volumes ranging from 0.44 to 1.0 cm(3)/g and Brunauer-Emmett-Teller surface areas ranging from 1000 to 1600 m(2)/g, the largest values of which are ∼150% and ∼60% higher than the theoretical values of defect-free UiO-66 crystal, respectively. The linker vacancies also have profound effects on the gas adsorption behaviors of UiO-66, in particular CO2. Finally, comparing the gas adsorption of hydroxylated and dehydroxylated UiO-66, we found that the former performs systematically better than the latter (particularly for CO2) suggesting the beneficial effect of the -OH groups. This finding is of great importance because hydroxylated UiO-66 is the practically more relevant, non-air-sensitive form of this MOF. The preferred gas adsorption on the metal center was confirmed by neutron diffraction measurements, and the gas binding strength enhancement by the -OH group was further supported by our first-principles calculations.

Methane storage in metal-organic frameworks: current records, surprise findings, and challenges.

We have examined the methane uptake properties of six of the most promising metal organic framework (MOF) materials: PCN-14, UTSA-20, HKUST-1, Ni-MOF-74 (Ni-CPO-27), NU-111, and NU-125. We discovered that HKUST-1, a material that is commercially available in gram scale, exhibits a room-temperature volumetric methane uptake that exceeds any value reported to date. The total uptake is about 230 cc(STP)/cc at 35 bar and 270 cc(STP)/cc at 65 bar, which meets the new volumetric target recently set by the Department of Energy (DOE) if the packing efficiency loss is ignored. We emphasize that MOFs with high surface areas and pore volumes perform better overall. NU-111, for example, reaches ~75% of both the gravimetric and the volumetric targets. We find that values for gravimetric uptake, pore volume, and inverse density of the MOFs we studied scale essentially linearly with surface area. From this linear dependence, we estimate that a MOF with surface area 7500 m(2)/g and pore volume 3.2 cc/g could reach the current DOE gravimetric target of 0.5 g/g while simultaneously exhibiting around ~200 cc/cc volumetric uptake. We note that while values for volumetric uptake are based on ideal single crystal densities, in reality the packing densities of MOFs are much lower. Finally, we show that compacting HKUST-1 into wafer shapes partially collapses the framework, decreasing both volumetric and gravimetric uptake significantly. Hence, one of the important challenges going forward is to find ways to pack MOFs efficiently without serious damage or to synthesize MOFs that can withstand substantial mechanical pressure.

Neon and CO2 adsorption on open carbon nanohorns.

We present the results of a thermodynamics and kinetics study of the adsorption of neon and carbon dioxide on aggregates of chemically opened carbon nanohorns. Both the equilibrium adsorption characteristics, as well as the dependence of the kinetic behavior on sorbent loading, are different for these two adsorbates. For neon the adsorption isotherms display two steps before reaching the saturated vapor pressure, corresponding to adsorption on strong and on weak binding sites; the isosteric heat of adsorption is a decreasing function of sorbent loading (this quantity varies by about a factor of 2 on the range of loadings studied), and the speed of the adsorption kinetics increases with increasing loading. By contrast, for carbon dioxide there are no substeps in the adsorption isotherms; the isosteric heat is a nonmonotonic function of loading, the value of the isosteric heat never differs from the bulk heat of sublimation by more than 15%, and the kinetic behavior is opposite to that of neon, with equilibration times increasing for higher sorbent loadings. We explain the difference in the equilibrium properties observed for neon and carbon dioxide in terms of differences in the relative strengths of adsorbate-adsorbate to adsorbate-sorbent interaction for these species.

CF4 on carbon nanotubes: physisorption on grooves and external surfaces.

We present the combined results of a computer simulation and adsorption isotherm investigation of CF4 films on purified HiPco nanotubes. The experimental measurements found two substeps in the adsorption data. The specific surface area of the sample and the coverage dependence of the isosteric heat of adsorption of the films were determined from the measurements. The simulations, conducted for homogeneous bundles of close-ended tubes, also found two substeps in the first layer data: one corresponding to adsorption on the grooves and a second one, at higher pressures, corresponding to adsorption on the outside surface of the tubes. Our computer simulations are in very good agreement with the experimental data.

Adsorption of xenon on purified HiPco single walled carbon nanotubes.

We have measured adsorption of xenon on purified HiPco single-walled carbon nanotubes (SWNTs) for coverages in the first layer. We compare the results on this substrate to those our group obtained in earlier measurements on lower purity arc-discharge produced nanotubes. To obtain an estimate for the binding energy of Xe, we measured five low-coverage isotherms for temperatures between 220 and 260 K. We determined a value of 256 meV for the binding energy; this value is 9% lower than the value we found for arc discharge nanotubes and is 1.59 times the value found for this quantity on planar graphite. We have measured five full monolayer isotherms between 150 and 175 K. We have used these data to obtain the coverage dependence of the isosteric heat. The experimental values obtained are compared with previously published computer simulation results for this quantity.

Isosteric heat of argon adsorbed on single-walled carbon nanotubes prepared by laser ablation.

We have measured 21 adsorption isotherms for argon on single-walled carbon nanotubes produced by laser ablation. We explored temperatures between 40 and 153 K to obtain the coverage dependence of the isosteric heat of adsorption for films in the first and second layers. Our data are compared to results obtained in computer simulation studies and to data obtained in previous experimental investigations of this system.