An HVOF-Sprayed (Cr3C2-NiCr+Co) Composite Coating on Ductile Cast Iron: Microstructure, Mechanical Properties, and Scratch Resistance.

High-velocity oxy-fuel (HVOF) thermally sprayed Cr3C2-NiCr coatings have been shown to be effective in shielding important machinery and equipment components from wear in harsh, high-temperature conditions. In this investigation, the HVOF thermal spray coating technique was used to deposit Cr3C2-NiCr powder with 10% Co particles onto ductile cast iron. The effect of the Co particles on the mechanical, tribological, and microstructure characteristics of a Cr3C2-NiCr/ductile cast iron system was investigated. The microstructure analysis employed various techniques, including light microscopy, X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and energy-dispersive X-ray spectroscopy (EDS). Scratch tests were applied to analyze the coating quality and adhesion. The coatings created using the HVOF spray method with Cr3C2-NiCr powders mixed with Co particles exhibited a dense structure containing large Co particles, partially melted, and very fine Cr3C2 particles embedded into the NiCr alloy matrix. Additionally, they possessed high hardness and excellent adhesion to the substrate. The results of bending strength tests were also presented, together with information on the coating's microhardness and fracture toughness. These included an analysis of the cracks and delamination in the Cr3C2-NiCr/ductile cast iron system. It was observed that the addition of Co particles significantly increased the resistance to cracking and wear behavior in the studied system.

Development of a CT Image Analysis Model for Cast Iron Products Based on Artificial Intelligence Methods.

This paper presents an assessment of the possibility of using digital image classifiers for tomographic images concerning ductile iron castings. The results of this work can help the development of an efficient system suggestion allowing for decision making regarding the qualitative assessment of the casting process parameters. Special attention should be focused on the fact that automatic classification in the case of ductile iron castings is difficult to perform. The biggest problem in this aspect is the high similarity of the void image, which may be a sign of a defect, and the nodular graphite image. Depending on the parameters, the tests on different photos may look similar. Presented in this article are test scenarios of the module analyzing two-dimensional tomographic images focused on the comprehensive assessment by convolutional neural network models, which are designed to classify the provided image. For the purposes of the tests, three such models were created, different from each other in terms of architecture and the number of hyperparameters and trainable parameters. The described study is a part of the decision-making system, supporting the process of qualitative analysis of the obtained cast iron castings.

Investigations of Model Multilayer Ceramic Casting Molds in a Raw State by Nondestructive Methods.

This article presents the results of research on the use of modern nondestructive methods such as 3D scanning, thermography and computed tomography (CT) to assess the quality of multilayer ceramic molds. Tests were performed on spherical samples of multilayer ceramic molds in the raw state. Samples were made of molding sands composed of quartz and molochite powders, the alcoholic binder hydrolyzed ethyl silicate (ZKE) and an aqueous binder based on colloidal silica. Thickness measurements of spherical forms were made using a 3D scanner. Porosity measurements were made using CT. Additionally, thermography observations of the mold cooling process were made with controlled temperature and humidity. The results of temperature measurements of samples were compared with measurements of thickness and porosity. The practical goal was to determine the possibility of using thermography, 3D scanning and CT as a quick method for detecting mold defects by varying their thickness, porosity and cracks and for final verification of the ceramic molds' condition before casting.

Investigation on Microstructure, Mechanical and Wear Properties of HVOF Sprayed Composite Coatings (WC-Co + CR) On Ductile Cast Iron.

Recent work indicates that the high-velocity oxy-fuel (HVOF) thermal spraying WC-Co coatings have been used to enhance the wear resistance of various engineering components in a variety of industrial environments. In the present work, WC-Co powder, containing Cr particles in an amount of 10%, was deposited on ductile cast iron with the HVOF thermal spray coating technique. An investigation was conducted to determine the role of Cr particles in the WC-Co coating produced with the HVOF technique on microstructure, mechanical, and wear properties in a system of type: WC-Co coating/ductile cast iron. The microstructure of the HVOF-sprayed WC-Co + Cr coating was characterised by light microscopy, X-ray diffraction (XRD), scanning electron microscope (SEM), transmission electron microscope (TEM), and energy-dispersive X-ray spectroscopy (EDS). The analysis of the microstructure showed the formation of a coating with low porosity, compact structure, and good adhesion to the substrate with a typical lamellar structure composed of fine molten Cr particles and finely fragmented WC grains embedded in a Co matrix, reaching the size of nanocrystalline. The scratch test was applied for the analysis of the adhesion of coatings to the substrate. The erosion behaviour and mechanism of material removal was studied and discussed based on microstructural examinations. Moreover, the results were discussed in relation to the bending strength test, including cracks and delamination in the system of the WC-Co + Cr/ductile cast iron, as microhardness and erosion resistance of the coating. It was found that the addition of Cr particles to the WC-Co powder, which causes hardening of the binder phase is a key influence on increased mechanical and wear properties in the studied system. Additionally, due to the construction of nanostructured coatings, suitable proportion of hard and soft phases, the technique sprayed HVOF coatings have advantageous properties such as high density and good slurry erosion resistance.

Study on the Microstructure, Mechanical Properties, and Erosive Wear Behavior of HVOF Sprayed Al2O3-15 wt.%TiO2 Coating with NiAl Interlayer on Al-Si Cast Alloy.

Alumina oxide coatings are widely used in many industrial applications to improve corrosion protection, wear and erosion resistances, and thermal insulation of metallic surfaces. The paper presents study of the microstructure, mechanical, and wear properties of HVOF (high velocity oxy-fuel process) sprayed of Al2O3-15 wt.% TiO2 coating with the NiAl interlayer on the surface of Al-Si alloy castings. The microstructure of Al2O3-15 wt.% TiO2/NiAl coating was characterized by light microscopy, X-ray diffraction (XRD), scanning electron microscope (SEM), and energy dispersive X-ray spectroscopy (EDS). The analysis of the microstructure showed the formation of coating with low porosity, compact structure, good adhesion to the substrate with typical lamellar structure composed of a solid phase consisting of compounds included in the coating material and their phase variations. For analysis of the adhesion of coatings to the substrate, the scratch test was applied. An assessment of the erosive wear resistance of coatings was also carried out, confirming the significant impact of the interlayer as well as the microstructure and phase composition of the oxide coating on the wear resistance of the tested coating system. Moreover, the results were discussed in relation to the bending strength test, including cracks and delamination in the system of the Al2O3-15 wt.% TiO2/NiAl/Al-Si alloy as microhardness and erosion resistance of the coating. It was found that the introduction of the NiAl metallic interlayer significantly increased resistance to cracking and wear behavior in the studied system.

Uniformity of Thermoluminescence and Optically Stimulated Luminescence Signals Over the Length of Doped LiMgPO4 Crystal Rods Grown by Micro-Pulling-Down Method.

The purpose of this work was to systematically assess the distribution of thermoluminescence (TL) and optically stimulated luminescence (OSL) properties along the length of crystals grown by the micro-pulling-down method, in relation to the microstructure and distribution of activators. We analyzed lithium magnesium phosphate (LiMgPO4; LMP) crystals doped with terbium (Tb; 0.8 mol%) or with a combination of thulium (Tm; 0.8 mol% or 1.2 mol%) and boron (B; 10 mol%). Crystals of several centimeters in length and 3 mm in diameter were cut into 20-40 slices, depending on length. For each sample, TL glow curves and OSL decay curves were examined. Optical microscopy and scanning electron microscopy were used to assess the microstructure and elemental composition of several selected samples. Two-dimensional TL readouts were performed to identify the areas with higher and lower signal emission. Our study showed that there may be significant differences not only in LMP sensitivity along the crystal's axis but also on the surface of the slice. The distribution of activators varies depending on the type of crystals and strongly affects luminescence properties.