Applications and Uncertainty Estimation of Single Level Standard Addition Method ICP-MS for Elemental Analysis in Various Matrix.

The standard addition method (SAM) based on gravimetric sample preparation was investigated as an approach for the removal or cancelling of matrix effects in measurements by inductively coupled plasma mass spectrometry (ICP-MS). Deduction of the equations and experimental confirmation of the method are both given in the present work. After measuring both spiked and non-spiked samples by ICP-MS, the concentration of an element could be calculated based on the signal intensity ratio to an internal standard. A practical example was provided for the measurement of Fe in a certified reference material (CRM), i.e. NMIJ CRM 7512-a (milk powder). The validity of the method had been confirmed by the results of international comparisons with various kinds of matrix, including bioethanol, human serum, biodiesel fuel, drinking water, infant formula milk power, and seafood. The suggested method had been applied to measurements of multiple elements in three CRMs, including tap water, milk powder, and tea leave powder, respectively.

Development of a Certified Reference Material (NMIJ CRM 7203-a) for Elemental Analysis of Tap Water.

A certified reference material (CRM), NMIJ CRM 7203-a, was developed for the elemental analysis of tap water. At least two independent analytical methods were applied to characterize the certified value of each element. The elements certified in the present CRM were as follows: Al, As, B, Ca, Cd, Cr, Cu, Fe, K, Mg, Mn, Mo, Na, Ni, Pb, Rb, Sb, Se, Sr, and Zn. The certified value for each element was given as the (property value ± expanded uncertainty), with a coverage factor of 2 for the expanded uncertainty. The expanded uncertainties were estimated while considering the contribution of the analytical methods, the method-to-method variance, the sample homogeneity, the long-term stability, and the concentrations of the standard solutions for calibration. The concentration of Hg (0.39 µg kg-1) was given as the information value, since loss of Hg was observed when the sample was stored at room temperature and exposed to light. The certified values of selected elements were confirmed by a co-analysis carried out independently by the NMIJ (Japan) and the KRISS (Korea).

Selective encapsulation of cesium ions using the cyclic peptide moiety of surfactin: Highly efficient removal based on an aqueous giant micellar system.

Cyclic peptide of surfactin (SF) is one of the promising environment-friendly biosurfactants abundantly produced by microorganisms such as Bacillus subtilis. SF is also known to act as an ionophore, wherein alkali metal ions can be trapped in the cyclic peptide. Especially, SF is expected to show high affinity for Cs(+) because of the distinctive cavity size and coordination number. In this study, we reported the specific interaction between SF and Cs(+) and succeeded in the highly efficient removal of Cs(+) from water using giant SF micelles as a natural sorbent. The specific interaction between SF and Cs(+) to form their inclusion complex was revealed by nuclear magnetic resonance (NMR) and Fourier transform infrared (FT-IR) spectroscopy. We found that SF micelles selectively encapsulate Cs(+), which was suggested by matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOFMS). A highly effective separation of Cs(+) immobilized on the surface of the SF micelles was also achieved through facile centrifugal ultrafiltration in 91% even in coexisting with other alkali metal ions such as Na(+) and K(+). Thus, the use of the giant micellar system of SF with its high Cs(+) affinity and distinctive assembling properties would be a new approach for the treatment of contaminated soil and water.

Proficiency testing for determination of pesticide residues in soybean: comparison of assigned values from participants' results and isotope-dilution mass spectrometric determination.

Proficiency testing (PT) for the determination of pesticide residues in soybean samples was organized by the National Metrology Institute of Japan (NMIJ). The candidate certified reference material, NMIJ CRM 7509-a, that was prepared from the raw soybeans containing target pesticides (diazinon, fenitrothion, chlorpyrifos, and permethrin) was used as the test sample. Forty participants submitted two sets of analytical results along with the details of the analytical method and conditions they applied. Two types of assigned values were established for each target pesticide: one was derived from the analytical results of the participants, and the other was provided from the analytical results by isotope-dilution mass spectrometry (IDMS). The latter values were 7.4-16% higher than the former values, plausibly because the analytical values from the IDMS measurements were not affected by the recovery ratio of the target pesticides during the analytical process. Thus, two kinds of z-scores were calculated for individual participants using the corresponding assigned values: one (z1-score) showed the relative performance score for the present PT and the other (z2-score) could be used for evaluation of the trueness of their analytical methods.

Identification of possible technical problems in determination of the major inorganic constituents of brown-rice flour by evaluating proficiency test results.

To support skill upgrading in analysis of inorganic constituents of environmental and food samples, the National Metrology Institute of Japan (NMIJ) and the National Food Research Institute (NFRI) have organized a proficiency test (PT) of determination of Mn, Fe, Cu, Zn, As, and Cd in brown-rice flour based on the international standard (ISO/IEC 17043:2010). One hundred and thirty-three sets of reports were assessed by use of the E(n)-number and z-score approaches in accordance with ISO/IEC 17043 and the international harmonized protocol for PT. The PT results and analytical procedures, reported in detail, were reviewed, and possible technical reasons for questionable or unsatisfactory results are discussed.

Development of a certified reference material (NMIJ CRM 7512-a) for the determination of trace elements in milk powder.

A certified reference material (CRM), NMIJ CRM 7512-a, was developed for the determination of trace elements in milk powder. At least three independent analytical methods were applied to characterize the certified value of each element; all of these analytical methods were based on microwave acid digestions and carried out using different analytical instruments. The certified value was given on a dry-mass basis, where the dry-mass correction factor was obtained by drying the sample at 65°C for 15 to 25 h. The certified values in the units of mass fractions for 13 elements were as follows: Ca, 8.65 (0.38) g kg(-1); Fe, 0.104 (0.007) g kg(-1); K, 8.41 (0.33) g kg(-1); Mg, 0.819 (0.024) g kg(-1); Na, 1.87 (0.09) g kg(-1); P, 5.62 (0.23) g kg(-1); Ba, 0.449 (0.013) mg kg(-1); Cu, 4.66 (0.23) mg kg(-1); Mn, 0.931 (0.032) mg kg(-1); Mo, 0.223 (0.012) mg kg(-1); Rb, 8.93 (0.31) mg kg(-1); Sr, 5.88 (0.20) mg kg(-1); and Zn, 41.3 (1.4) mg kg(-1), where the numbers in the parentheses are the expanded uncertainties with a coverage factor of 2. The expanded uncertainties were estimated considering the contribution of the analytical methods, the method-to-method variance, the sample homogeneity, the dry-mass correction factor, and the concentrations of the standard solutions for calibration. The concentrations of As (2.1 µg kg(-1)), Cd (0.2 µg kg(-1)), Cr (1.3 µg kg(-1)), Pb (0.3 µg kg(-1)), and Y (64 µg kg(-1)) were given as information values for the present CRM.

Development of a certified reference material (NMIJ CRM 7531-a) for the determination of trace cadmium and other elements in brown rice flour.

A certified reference material (CRM) for trace cadmium and other elements in brown rice flour was developed at the National Metrology Institute of Japan (NMIJ). The CRM was provided as a dry powder after drying and frozen pulverization of fresh brown rice obtained from a Japanese domestic market. Characterization of the property value for each element was carried out exclusively by NMIJ with at least two independent analytical methods, including inductively coupled plasma mass spectrometry (ICP-MS), ICP high-resolution mass spectrometry, isotope-dilution ICP-MS, ICP optical emission spectrometry, and graphite-furnace atomic-absorption spectrometry. Property values were provided for six elements (Mn, Fe, Cu, Zn, As, and Cd). The concentration range of the property values was from 0.280 mg kg(-1) of As to 31.8 mg kg(-1) of Zn. The combined relative standard uncertainties of the property values were estimated by considering the uncertainties of the homogeneity, characterization, difference among analytical methods, dry-mass correction factor, and calibration standard. The range of the relative combined standard uncertainties was from 1.1% of Zn to 1.6% of As.

Preparation and certification of hijiki reference material, NMIJ CRM 7405-a, from the edible marine algae hijiki (Hizikia fusiforme).

A certified reference material, NMIJ CRM 7405-a, for the determination of trace elements and As(V) in algae was developed from the edible marine hijiki (Hizikia fusiforme) and certified by the National Metrology Institute of Japan (NMIJ), the National Institute of Advanced Industrial Science and Technology (AIST). Hijiki was collected from the Pacific coast in the Kanto area of Japan, and was washed, dried, powdered, and homogenized. The hijiki powder was placed in 400 bottles (ca. 20 g each). The concentrations of 18 trace elements and As(V) were determined by two to four independent analytical techniques, including (ID)ICP-(HR)MS, ICP-OES, GFAAS, and HPLC-ICP-MS using calibration solutions prepared from the elemental standard solution of Japan calibration service system (JCSS) and the NMIJ CRM As(V) solution, and whose concentrations are certified and SI traceable. The uncertainties of all the measurements and preparation procedures were evaluated. The values of 18 trace elements and As(V) in the CRM were certified with uncertainty (k = 2).

Development of a certified reference material (NMIJ CRM 7505-a) for the determination of trace elements in tea leaves.

A certified reference material (CRM) for trace elements in tea leaves has been developed in National Metrology Institute of Japan (NMIJ). The CRM was provided as a dry powder (<90 µm) after frozen pulverization of washed and dried fresh tea leaves from a tea plant farm in Shizuoka Prefecture, Japan. Characterization of the property value for each element was carried out exclusively by NMIJ with at least two independent analytical methods, including inductively coupled plasma mass spectrometry (ICP-MS), high-resolution (HR-) ICP-MS, isotope-dilution (ID-) ICP-MS, inductively coupled plasma optical emission spectrometry (ICP-OES), graphite-furnace atomic-absorption spectrometry (GF-AAS) and flame atomic-absorption spectrometry (FAAS). Property values were provided for 19 elements (Ca, K, Mg, P, Al, B, Ba, Cd, Cu, Fe, Li, Mn, Na, Ni, Pb, Rb, Sr, Zn and Co) and informative values for 18 elements (Ti, V, Cr, Y, and all of the lanthanides, except for Pm whose isotopes are exclusively radioactive). The concentration ranges of property values and informative values were from 1.59% (mass) of K to 0.0139 mg kg(-1) of Cd and from 0.6 mg kg(-1) of Ti to 0.0014 mg kg(-1) of Lu, respectively. Combined relatively standard uncertainties of the property values were estimated by considering the uncertainties of the homogeneity, analytical methods, characterization, calibration standard, and dry-mass correction factor. The range of the relative combined standard uncertainties was from 1.5% of Mg and K to 4.1% of Cd.

Accurate determination of arsenic in arsenobetaine standard solutions of BCR-626 and NMIJ CRM 7901-a by neutron activation analysis coupled with internal standard method.

Neutron activation analysis (NAA) coupled with an internal standard method was applied for the determination of As in the certified reference material (CRM) of arsenobetaine (AB) standard solutions to verify their certified values. Gold was used as an internal standard to compensate for the difference of the neutron exposure in an irradiation capsule and to improve the sample-to-sample repeatability. Application of the internal standard method significantly improved linearity of the calibration curve up to 1 microg of As, too. The analytical reliability of the proposed method was evaluated by k(0)-standardization NAA. The analytical results of As in AB standard solutions of BCR-626 and NMIJ CRM 7901-a were (499+/-55)mgkg(-1) (k=2) and (10.16+/-0.15)mgkg(-1) (k=2), respectively. These values were found to be 15-20% higher than the certified values. The between-bottle variation of BCR-626 was much larger than the expanded uncertainty of the certified value, although that of NMIJ CRM 7901-a was almost negligible.

Preparation and certification of arsenate [As(V)] reference material, NMIJ CRM 7912-a.

Arsenate [As(V)] solution reference material, National Metrology Institute of Japan (NMIJ) certified reference material (CRM) 7912-a, for speciation of arsenic species was developed and certified by NMIJ, the National Institute of Advanced Industrial Science and Technology. High-purity As(2)O(3) reagent powder was dissolved in 0.8 M HNO(3) solution and As(III) was oxidized to As(V) with HNO(3) to prepare 100 mg kg(-1) of As(V) candidate CRM solution. The solution was bottled in 400 bottles (50 mL each). The concentration of As(V) was determined by four independent analytical techniques-inductively coupled plasma mass spectrometry, inductively coupled plasma optical emission spectrometry, graphite furnace atomic absorption spectrometry, and liquid chromatography inductively coupled plasma mass spectrometry-according to As(V) calibration solutions, which were prepared from the arsenic standard of the Japan Calibration Service system and whose species was guaranteed to be As(V) by NMIJ. The uncertainties of all the measurements and preparation procedures were evaluated. The certified value of As(V) in the CRM is (99.53 +/- 1.67) mg kg(-1) (k = 2).

Precise determination of Cr and Co in certified reference material of silicon nitride by neutron activation analysis using internal standardization.

Neutron activation analysis with an internal standard correction was applied to the determination of Cr and Co in a ceramics certified reference material (NMIJ CRM 8004-a silicon nitride powder). Cesium was used as an internal standard to compensate for any inhomogeneity of the neutron flux through an irradiation capsule and to improve the repeatability of gamma-ray measurements. It was found that the linearity of the calibration curves of Cr and Co was improved by using an internal standard. The analytical results of Cr and Co in NMIJ CRM 8004-a were in good agreement with those obtained by ICP-OES, ICP-sector field mass spectrometry (ICP-SFMS), and isotope dilution/ICP-SFMS for Cr. The relative expanded uncertainties (k = 2) were 1.9% for Cr and 1.5% for Co. The uncertainties were comparable to those of atomic spectrometric methods.

Rapid determination of arsenic species in freshwater organisms from the arsenic-rich Hayakawa River in Japan using HPLC-ICP-MS.

Speciation analyses of water-soluble arsenicals from freshwater and biological samples collected from the Hayakawa River (Kanagawa, Japan), which contains a high concentration of arsenic, were performed using high performance liquid chromatography/inductively coupled plasma mass spectrometry (HPLC-ICP-MS). River water contained only arsenate, which is a pentavalent inorganic arsenical. The water bug Stenopsyche marmorata contained inorganic arsenicals accounting for 77% of the water-soluble arsenicals, followed by oxo-arsenosugar-glycerol, which is a type of dimethylarsinoylriboside (arsenosugar). The freshwater green macroalga Cladophora glomerata contained oxo-arsenosugar-glycerol and oxo-arsenosugar-phosphate as 64% of the water-soluble arsenicals. Production of the same types of arsenosugars was confirmed in the freshwater green microalga Chlamydomonas reinhardtii CC125 experimentally exposed to arsenate. The muscle tissues of all freshwater fish and crustaceans analyzed contained arsenobetaine, oxo-arsenosugar-glycerol, and/or oxo-arsenosugar-phosphate in various concentrations. Seven freshwater fish (Cobitis biwae, Leuciscus hakonensis, Phoxinus lagowski steindachneri, Plecoglossus altivelis, Rhinogobius sp. CB, Rhinogobius sp. CO, Sicyopterus japonicus) and the crustacean Macrobracbium nipponenese contained arsenobetaine in their muscle tissues as the predominant form, contributing up to 80% of the water-soluble arsenicals, while the freshwater fish Anguilla japonica muscle tissues primarily contained dimethylarsinic acid as 77% of the water-soluble arsenicals, followed by arsenobetaine. The freshwater fish Zacco platypus muscle tissues predominantly contained oxo-arsenosugar-phosphate, accounting for 51% of the water-soluble arsenicals, followed by dimethylarsinic acid and arsenobetaine. These biological samples possessed non-extractable arsenical(s) accounting for more than 50% of the total arsenic concentration.

The extraction and speciation of arsenic in rice flour by HPLC-ICP-MS.

Several solvent mixtures and techniques for the extraction of arsenic (As) species from rice flour samples prior to their analysis by HPLC-ICP-MS were investigated. Microwave-assisted extraction using water at 80 degrees C for 30 min provided the highest extraction efficiency. Total recoveries of extracted As species were in good agreement with the total As concentrations determined by ICP-MS after microwave-assisted acid digestion of the samples. Arsenite [As(III)], arsenate [As(V)] and dimethylarsinic acid (DMAA) were the main species detected in rice flour samples.

Certification of methylmercury in cod fish tissue certified reference material by species-specific isotope dilution mass spectrometric analysis.

A new cod fish tissue certified reference material, NMIJ CRM 7402-a, for methylmercury analysis was certified by the National Metrological Institute of Japan in the National Institute of Advanced Industrial Science and Technology (NMIJ/AIST). Cod fish was collected from the sea close to Japan. The cod muscle was powdered by freeze-pulverization and was placed into 600 glass bottles (10 g each), which were sterilized with gamma-ray irradiation. The certification was carried out using species-specific isotope dilution gas chromatography inductively coupled plasma mass spectrometry (SSID-GC-ICPMS), where (202)Hg-enriched methylmercury (MeHg) was used as the spike compound. In order to avoid any possible analytical biases caused by nonquantitative extraction, degradation and/or formation of MeHg in sample preparations, two different extraction methods (KOH/methanol and HCl/methanol extractions) were performed, and one of these extraction methods utilized two different derivatization methods (ethylation and phenylation). A double ID method was adopted to minimize the uncertainty arising from the analyses. In order to ensure not only the reliability of the analytical results but also traceability to SI units, the standard solution of MeHg used for the reverse-ID was prepared from high-purity MeHg chloride and was carefully assayed as follows: the total mercury was determined by ID-ICPMS following aqua regia digestion, and the ratio of Hg as MeHg to the total Hg content was estimated by GC-ICPMS. The certified value given for MeHg is 0.58 +/- 0.02 mg kg(-1) as Hg.

Effect of the chemical species of arsenic on sensitivity in graphite furnace atomic absorption spectrometry.

The sensitivity of graphite furnace atomic absorption spectrometry (GFAAS) to arsenobetaine (AB) was 1.3-times higher than to inorganic As. In order to understand the mechanism underlying this observation, the atomization processes for both chemical species were investigated in terms of the enthalpy change (DeltaH) during the atomization process in GFAAS. The enthalpy change of AB was slightly lower than that of inorganic As, which suggested that AB was atomized more efficiently than was inorganic As. Moreover, it was observed that some co-existing organic materials enhanced the analytical sensitivity of inorganic As. The sensitivity difference between inorganic As and AB depended upon the mechanisms of their atomization processes.

Preparation and certification of arsenobetaine reference material NMIJ CRM 7901-a.

An arsenobetaine [(CH(3))(3)As(+)CH(2)COO(-)] solution reference material, NMIJ CRM 7901-a, intended for use in the speciation of arsenic compounds, was developed and certified by the National Metrology Institute of Japan (NMIJ), part of the National Institute of Advanced Industrial Science and Technology (AIST). The high-purity arsenobetaine powder was synthesized from trimethylarsine [(CH(3))(3)As], and it was dissolved in water in order to prepare 20 mg kg(-1) of arsenobetaine standard solution. The solution was bottled in 500 bottles (each containing 10 ml). Certification of the CRM for arsenobetaine was conducted by NMIJ. The concentration of As was determined by four independent analytical techniques (ICP-MS, ICP-OES, GFAAS and LC-ICP-MS), and each result was converted to the arsenobetaine concentration by applying an appropriate factor. The arsenobetaine concentration in the CRM was thus certified.

Study on simultaneous speciation of arsenic and antimony by HPLC-ICP-MS.

A method was developed for the simultaneous speciation of arsenic and antimony with HPLC-ICP-MS using C30 reversed phase column. Eight kinds of arsenic compounds (As(III), As(V), monomethylarsonic acid (MMAA), dimethylarsinic acid (DMAA), arsenobetaine (AB), arsenocholine (AsC), trimethylarsine oxide (TMAO) and tetramethylarsonium (TeMA)), Sb(III) and Sb(V) were simultaneously separated by the special mobile phase containing ammonium tartrate. Especially for the species of organic As, a C30 column was better than a C18 column in the effect of separation. Limits of detection (LOD) for these elements were 0.2 ng ml(-1) for the species of each As, and 0.5 ng ml(-1) for the species of each Sb, when a 10 microl of sample was injected, respectively. The proposed method was applied to a hot spring water and a fish sample.

Mechanism of sensitivity difference between trivalent inorganic As species [As(III)] and pentavalent species [As(V)] with inductively coupled plasma spectrometry.

The pentavalent inorganic arsenic (As) species [As(V)] is found to be 4% more sensitive than the trivalent species [As(III)] with inductively coupled plasma mass spectrometry (ICP-MS) and inductively coupled plasma optical emission spectrometry (ICP-OES). Although there was no sensitivity difference between As(III) and As(V) with atomic absorption spectrometry (AAS), electrothermal atomization atomic absorption spectrometry (ETAAS), X-ray fluorescence (XRF), and neutron activation analysis (NAA). The calibration solutions of As(III) and As(V) were gravimetrically prepared from the unique mother standard solution of JCSS As standard solution which is certified by Japan Calibration Service System (JCSS). Since it is essential to use the calibration solutions with exactly the same concentration of As in order to accurately compare the sensitivities between As(III) and As(V). The mechanisms of this sensitivity difference between them were investigated by ICP-MS and ICP-OES, and it elucidated that the formation rates of hydride polyatomic species of As were definitively different between As(III) and As(V) species in the plasma. This phenomenon directly affected their sensitivities with ICP-MS and ICP-OES.

Certification of mono-, di-, and tributyltin compounds in marine sediment certified reference material by species-specific isotope dilution mass spectrometric analysis using synthesized 118Sn-labeled butyltins.

A new marine sediment reference material (NMIJ CRM 7301-a) for butyltins analysis was prepared and certified by the National Metrological Institute of Japan, National Institute of Advanced Industrial Science and Technology (NMIJ/AIST). The original material of the sediment was collected at a bay near industrial activities in Japan. The sediment material was air-dried, sieved, homogenized, and packaged into 1,000 glass bottles (60 g each). Certification of NMIJ CRM 7301-a was carried out at NMIJ using two different types of species-specific isotope dilution mass spectrometry: isotope dilution-ethylation-gas chromatography/inductively coupled plasma mass spectrometry (GC/ICPMS) and isotope dilution-ethylation-gas chromatography/mass spectrometry (GC/MS). A mixture of (118)Sn-enriched monobutyltin, dibutyltin, and tributyltin was synthesized in our laboratory and was used as a spike for both techniques. Certified values are given for tributyltin (0.044+/-0.004 mg kg(-1) as Sn), dibutyltin (0.056+/-0.006 mg kg(-1) as Sn, and monobutyltin (0.058+/-0.013 mg kg(-1) as Sn), being at lower levels than currently available sediment CRMs for the analysis of organotins.