Removal of nutrients from pulp and paper biorefinery effluent: Operation, kinetic modelling and optimization by response surface methodology.

This study investigated the effectiveness of extended aeration system (EAS) and rice straw activated carbon-extended aeration system (RAC-EAS) in the treatment of pulp and paper biorefinery effluent (PPBE). RAC-EAS focused on the efficient utilization of lignocellulosic biomass waste (rice straw) as a biosorbent in the treatment process. The experiment was designed by response surface methodology (RSM) and conducted using a bioreactor that operated at 1-3 days hydraulic retention times (HRT) with PPBE concentrations at 20, 60 and 100%. The bioreactor was fed with real PPBE having initial ammonia-N and total phosphorus (TP) concentrations that varied between 11.74 and 59.02 mg/L and 31-161 mg/L, respectively. Findings from the optimized approach by RSM indicated 84.51% and 91.71% ammonia-N and 77.62% and 84.64% total phosphorus reduction in concentration for EAS and RAC-EAS, respectively, with high nitrification rate observed in both bioreactors. Kinetic model optimization indicated that modified stover models was the best suited and were statistically significant (R2 ≥ 0.98) in the analysis of substrate removal rates for ammonia-N and total phosphorus. Maximum nutrients elimination was attained at 60% PPBE and 48 h HRT. Therefore, the model can be utilized in the design and optimization of EAS and RAC-EAS systems and consequently in the prediction of bioreactor behavior.

Produced Water Treatment with Conventional Adsorbents and MOF as an Alternative: A Review.

A large volume of produced water (PW) has been produced as a result of extensive industrialization and rising energy demands. PW comprises organic and inorganic pollutants, such as oil, heavy metals, aliphatic hydrocarbons, and radioactive materials. The increase in PW volume globally may result in irreversible environmental damage due to the pollutants' complex nature. Several conventional treatment methods, including physical, chemical, and biological methods, are available for produced water treatment that can reduce the environmental damages. Studies have shown that adsorption is a useful technique for PW treatment and may be more effective than conventional techniques. However, the application of adsorption when treating PW is not well recorded. In the current review, the removal efficiencies of adsorbents in PW treatment are critically analyzed. An overview is provided on the merits and demerits of the adsorption techniques, focusing on overall water composition, regulatory discharge limits, and the hazardous effects of the pollutants. Moreover, this review highlights a potential alternative to conventional technologies, namely, porous adsorbent materials known as metal-organic frameworks (MOFs), demonstrating their significance and efficiency in removing contaminants. This study suggests ways to overcome the existing limitations of conventional adsorbents, which include low surface area and issues with reuse and regeneration. Moreover, it is concluded that there is a need to develop highly porous, efficient, eco-friendly, cost-effective, mechanically stable, and sustainable MOF hybrids for produced water treatment.

A Systematic Literature Review on Waste-to-Resource Potential of Palm Oil Clinker for Sustainable Engineering and Environmental Applications.

Several agro-waste materials have been utilized for sustainable engineering and environmental application over the past decades, showing different degrees of effectiveness. However, information concerning the wider use of palm oil clinker (POC) and its performance is still lacking. Therefore, as a solid waste byproduct produced in one of the oil palm processing stages, generating a huge quantity of waste mostly dumped into the landfill, the waste-to-resource potential of POC should be thoroughly discussed in a review. Thus, this paper provides a systematic review of the current research articles on the several advances made from 2005 to 2021 regarding palm oil clinker physical properties and performances, with a particular emphasis on their commitments to cost savings during environmental and engineering applications. The review begins by identifying the potential of POC application in conventional and geopolymer structural elements such as beams, slabs, and columns made of concrete, mortar, or paste for coarse aggregates, sand, and cement replacement. Aspects such as performance of POC in wastewater treatment processes, fine aggregate and cement replacement in asphaltic and bituminous mixtures during highway construction, a bio-filler in coatings for steel manufacturing processes, and a catalyst during energy generation are also discussed. This review further describes the effectiveness of POC in soil stabilization and the effect of POC pretreatment for performance enhancement. The present review can inspire researchers to find research gaps that will aid the sustainable use of agroindustry wastes. The fundamental knowledge contained in this review can also serve as a wake-up call for researchers that will motivate them to explore the high potential of utilizing POC for greater environmental benefits associated with less cost when compared with conventional materials.

Improved anaerobic digestion of palm oil mill effluent and biogas production by ultrasonication pretreatment.

Palm oil mill effluent (POME) is a highly polluted wastewater that consists of a high organic content of 4-5% total solids; a potential renewable energy source. A waste to energy study was conducted to improve biogas production using POME as substrate by ultrasonication pretreatment at mesophilic temperatures. The effect of temperature on the specific growth rate of anaerobes and methanogenic activity was investigated. Five sets of assays were carried out at operating temperatures between 25 °C and 45 °C. Each set consisted of two experiments using identical anaerobic sequencing batch reactors (AnSBR); fed with raw POME (control) and sonicated POME, respectively. The ultrasonication was set at 16.2 min ultrasonication time and 0.88 W mL-1 ultrasonication density with substrate total solids concentration of 6% (w/v). At 25 °C, biogas production rate and organic matter removal exhibited lowest values for both reactors. The maximum organic degradation was 96% from AnSBR operated at 30 °C fed with sonicated POME and 91% from AnSBR operated at 35 °C fed with unsonicated POME. In addition, the methane yield from AnSBR operated at 30 °C was enhanced by 21.5% after ultrasonication pretreatment. A few normality tests and a t-test were carried out. Both tests indicated that the residuals of the experimental data were normality distributed with mean equals to zero. The results demonstrated that ultrasonication treatment was a promising pretreatment to positively affect the organic degradation and biogas production rates at 30-35 °C.

Lipid for biodiesel production from attached growth Chlorella vulgaris biomass cultivating in fluidized bed bioreactor packed with polyurethane foam material.

The potential to grow attached microalgae Chlorella vulgaris in fluidized bed bioreactor was materialized in this study, targeting to ease the harvesting process prior to biodiesel production. The proposed thermodynamic mechanism and physical property assessment of various support materials verified polyurethane to be suitable material favouring the spontaneous adhesion by microalgae cells. The 1-L bioreactor packed with only 2.4% (v/v) of 1.00-mL polyurethane foam cubes could achieve the highest attached growth microalgae biomass and lipid weights of 812±122 and 376±37mg, respectively, in comparison with other cube sizes. The maturity of attached growth microalgae biomass for harvesting could also be determined from the growth trend of suspended microalgae biomass. Analysis of FAME composition revealed that the harvested microalgae biomass was dominated by C16-C18 (>60%) and mixture of saturated and mono-unsaturated fatty acids (>65%), satiating the biodiesel standard with adequate cold flow property and oxidative stability.

Feasibility study of biodiesel production using lipids of Hermetia illucens larva fed with organic waste.

Hermetia illucens larvae by nature are a decomposer which fed on organic wastes. This study explores the potential of producing biodiesel using lipids from H. illucens larvae. Three types of organic wastes (sewage sludge, fruit waste and palm decanter cake from oil palm mill) were selected based on considerable generation and disposal concern in the area of study as well as lack of investigations as feed for Hermetia illucens larvae in current literatures. Growth rate of the larvae was determined with studying the changes in the biomass per day. H. illucens larvae fed with fruit waste and palm decanter cake have shown growth rates of 0.52±0.02 and 0.23±0.09 g d(-1), respectively. No positive sign of growth were observed in the larvae fed with treated sewage sludge (-0.04±0.01 g d(-1)). Biodiesel as fatty acid methyl ester (FAME) was synthesized by transesterification of the larvae lipid using sulphuric acid as catalyst in methanol. FAME produced was ascertained using ATR-FTIR spectroscopy and GC-MS. The main compositions of fatty acid were found to be C12:0, C16:0 and C18:1n9c. Fatty acid composition of C12:0 fed with fruit waste, sewage sludge and palm decanter was found to be most abundant in the larvae lipid. The amount of C12:0 obtained was 76.13%, 58.31% and 48.06%, respectively. In addition, fatty acid of C16:0 was attained at 16.48% and 25.48% fed with sewage sludge and palm decanter, respectively. Based on the findings, FAME derived from larvae lipids is feasible to be used for biodiesel production.

Boron removal by electrocoagulation and recovery.

This work investigated the removal of boron from wastewater and its recovery by electrocoagulation and hydrothermal mineralization methods respectively. The experimental design was developed using Box-Behnken Model. An initial study was performed based on four preselected variables (pH, current density, concentration and time) using synthetic wastewater. Response surface methodology (RSM) was used to evaluate the effect of process variables and their interaction on boron removal. The optimum conditions were obtained as pH 6.3, current density 17.4 mA/cm(2), and time 89 min. At these applied optimum conditions, 99.7% boron removal from an initial concentration of 10.4 mg/L was achieved. The process was effectively optimized by RSM with a desirability value of 1.0. The results showed that boron removal efficiency enhanced with increase in current density and treatment time. Removal efficiency also increased when pH was increased from 4 to 7 and subsequently decreased at pH 10. Adsorption kinetics study revealed that the reaction followed pseudo second order kinetic model; evidenced by high correlation and goodness of fit. Thermodynamics study showed that mechanism of boron adsorption was chemisorption and the reaction was endothermic in nature. Furthermore, the adsorption process was spontaneous as indicated by negative values of the adsorption free energy. Treatment of real produced water using electrocoagulation resulted in 98% boron removal. The hydrothermal mineralization study showed that borate minerals (Inyoite, Takadaite and Nifontovite) can be recovered as recyclable precipitate from electrocoagulation flocs of produced water.

Polycyclic aromatic hydrocarbon removal from petroleum sludge cake using thermal treatment with additives.

Petroleum sludge is a hazardous waste that contains various organic compounds including polycyclic aromatic hydrocarbons (PAHs) which have carcinogenic-mutagenic and toxic characteristics. This study focuses on the thermal treatment (indirect heating) of petroleum sludge cake for PAH degradation at 250, 450, and 650 degrees C using Ca(OH)2 + NaHCO3 as an additive. The treatment was conducted in a rotary drum electric heater. All experiments were carried out in triplicate. Concentrations of the 16 priority PAHs in gas (absorbed on Amberlite XAD-4 adsorbent), particulate (on quartz filter) and residue phases were determined using gas chromatography-mass spectrometry (GC-MS). The samples were extracted with acetonitrile by ultra-sonication prior to GC-MS analysis. The use of additive was beneficial and a temperature of 450 degrees C was suitable for PAH degradation. Low levels of PAH emissions, particularly carcinogenic PAH and toxic equivalent concentration (sigma TEC), were observed in gas, particulate and residue phases after treatment.

Kinetic modeling and half life study on bioremediation of crude oil dispersed by Corexit 9500.

Hydrocarbon pollution in marine ecosystems occurs mainly by accidental oil spills, deliberate discharge of ballast waters from oil tankers and bilge waste discharges; causing site pollution and serious adverse effects on aquatic environments as well as human health. A large number of petroleum hydrocarbons are biodegradable, thus bioremediation has become an important method for the restoration of oil polluted areas. In this research, a series of natural attenuation, crude oil (CO) and dispersed crude oil (DCO) bioremediation experiments of artificially crude oil contaminated seawater was carried out. Bacterial consortiums were identified as Acinetobacter, Alcaligenes, Bacillus, Pseudomonas and Vibrio. First order kinetics described the biodegradation of crude oil. Under abiotic conditions, oil removal was 19.9% while a maximum of 31.8% total petroleum hydrocarbons (TPH) removal was obtained in natural attenuation experiment. All DCO bioreactors demonstrated higher and faster removal than CO bioreactors. Half life times were 28, 32, 38 and 58 days for DCO and 31, 40, 50 and 75 days for CO with oil concentrations of 100, 500, 1000 and 2000 mg/L, respectively. The effectiveness of Corexit 9500 dispersant was monitored in the 45 day study; the results indicated that it improved the crude oil biodegradation rate.

Application of statistical experimental methodology to optimize bioremediation of n-alkanes in aquatic environment.

Response surface methodology (RSM) was employed to optimize nitrogen and phosphorus concentrations for removal of n-alkanes from crude oil contaminated seawater samples in batch reactors. Erlenmeyer flasks were used as bioreactors; each containing 250 mL dispersed crude oil contaminated seawater, indigenous acclimatized microorganism and different amounts of nitrogen and phosphorus based on central composite design (CCD). Samples were extracted and analyzed according to US-EPA protocols using a gas chromatograph. During 28 days of bioremediation, a maximum of 95% total aliphatic hydrocarbons removal was observed. The obtained Model F-value of 267.73 and probability F<0.0001 implied the model was significant. Numerical condition optimization via a quadratic model, predicted 98% n-alkanes removal for a 20-day laboratory bioremediation trial using nitrogen and phosphorus concentrations of 13.62 and 1.39 mg/L, respectively. In actual experiments, 95% removal was observed under these conditions.

Landfill leachate treatment by electrochemical oxidation.

This study investigated the electrochemical oxidation of stabilized leachate from Pulau Burung semi-aerobic sanitary landfill by conducting laboratory experiments with sodium sulfate Na(2)SO(4) (as electrolyte) and graphite carbon electrodes. The control parameters were influent COD, current density and reaction time, while the responses were BOD removal, COD removal, BOD:COD ratio, color and pH. Na(2)SO(4) concentration was 1 g/L. Experiments were conducted based on a three-level factorial design and response surface methodology (RSM) was used to analyze the results. The optimum conditions were obtained as 1414 mg/L influent COD concentration, 79.9 mA/cm(2) current density and 4 h reaction time. This resulted in 70% BOD removal, 68% COD removal, 84% color removal, 0.04 BOD/COD ratio and 9.1 pH. Electrochemical treatment using graphite carbon electrode was found to be effective in BOD, COD and color removal but was not effective in increasing the BOD/COD ratio or enhancing biodegradability of the leachate. The color intensity of the treated samples increased at low influent COD and high current density due to corrosion of electrode material.

Removal of chromium (VI) from aqueous solution using treated oil palm fibre.

This study proposed an oil palm by-product as a low-cost adsorbent for the removal of hexavalent chromium [Cr (VI)] from aqueous solution. Adsorption of Cr (VI) by sulphuric acid and heat-treated oil palm fibre was conducted using batch tests. The influence of pH, contact time, initial chromium concentration and adsorbent dosage on the removal of Cr (VI) from the solutions was investigated. The optimum initial pH for maximum uptake of Cr (VI) from aqueous solution was found to be 1.5. The removal efficiency was found to correlate with the initial Cr (VI) concentration, adsorbent dosage as well as the contact time between Cr (VI) and the adsorbent. The adsorption kinetics tested with pseudo first order and pseudo second order models yielded high R(2) values from 0.9254 to 0.9870 and from 0.9936 to 0.9998, respectively. The analysis of variance (ANOVA) showed significant difference between the R(2) values of the two models at 99% confidence level. The Freundlich isotherm (R(2)=0.8778) described Cr (VI) adsorption slightly better than the Langmuir isotherm (R(2)=0.8715). Difficulty in desorption of Cr (VI) suggests the suitability of treated oil palm fibre as a single-use adsorbent for Cr (VI) removal from aqueous solution.