Design Strategies of Spinel Oxide Frameworks Enabling Reversible Mg-Ion Intercalation.

ConspectusReversible Mg2+ intercalation in metal oxide frameworks is a key enabler for an operational Mg-ion battery with high energy density needed for the next generation of energy storage technologies. While functional Mg-ion batteries have been achieved in structures with soft anions (e.g., S2- and Se2-), they do not meet energy density requirements to compete with the current rechargeable lithium-ion batteries due to their low insertion potentials. It emphasizes the necessity of finding an oxide-based cathode that operates at high potentials. A leading hypothesis to explain the limited availability of oxide Mg-ion cathodes is the belief that Mg2+ has sluggish diffusion kinetics in oxides due to strong electrostatic interactions between the Mg2+ ions and oxide anions in the lattice. From this assessment, it can be hypothesized that such rate limiting kinetic shortcomings can be mitigated by tailoring an oxide framework through creating less stable Mg2+-O2- coordination.Based on theoretical calculations and preliminary experimental data, oxide spinels have been identified as promising cathode candidates with storage capacity, insertion potential, and cation mobility that meet the requirements for a secondary Mg-ion battery. However, spinels with a single redox metal, such as MgCr2O4 or MgMn2O4, were not found to demonstrate sufficiently reversible Mg-ion intercalation at high redox potentials when coupled with nonaqueous Mg-electrolytes. Therefore, a materials development effort was initiated to design, synthesize, and evaluate a new class of solid-solution oxide spinels that can satisfy the required properties needed to create a sustainable Mg-ion cathode. These were designed by bringing together electrochemically active metals with stable redox potentials and charged states against the electrolyte, for instance, Mn3+, in combination with a structural stabilization component, typically Cr3+. Furthermore, common spinel structural defects that degrade performance, i.e., antisite inversion, were controlled to see correlation between structures and electrochemical overpotentials, thus controlling overall hysteresis. The designed materials were characterized by both short- and long-range structure in both ex situ and in situ modes to confirm the nature of solid-solution and to correlate structural changes and redox activity to electrochemical performance. Consistent and reproducible results were observed for facile bulk Mg2+-ion activity without phase transformations, leading to enhanced energy storage capability based on reversible intercalation of Mg2+, enabled by understanding the variables that control the electrochemical performance of the spinel oxide. Based on these observations, with proper materials design, it is possible to develop an oxide cathode material that has many of the desired properties of a Li-ion intercalation cathode, representing a significant mile marker in the quest for high energy density Mg-ion batteries.This Account describes strategies for the design and development of new spinel oxide intercalation materials for high-energy Mg-ion battery cathodes through a combination of theoretical and experimental approaches. We will review the key factors that govern the kinetics of Mg2+ diffusion in spinel oxides and illustrate how material complexity correlates with the electrochemical Mg2+ activity in oxides and is supported by secondary characterization. The understanding gained from the fundamental studies of cation diffusion in oxide cathodes will be beneficial for chemists and materials scientists who are developing rechargeable batteries.

Operando X-ray Diffraction Studies of the Mg-Ion Migration Mechanisms in Spinel Cathodes for Rechargeable Mg-Ion Batteries.

A promising high-voltage spinel oxide cathode material MgCrMnO4 with 18% Mg/Mn inversion was synthesized successfully. A new custom operando battery device was designed to study the cation migration mechanisms of the MgCrMnO4 cathode using 0.1 M Mg(TPFA)2 electrolyte dissolved in triglyme and activated carbon as the anode. For the first time in multivalent batteries, high-quality operando diffraction data enabled the accurate quantification of cation contents in the host structure. Besides the exceptional reversibility of 12% Mg2+ insertion in Mg1-xCrMnO4 (x ≤ 1), a partially reversible insertion of excess Mg2+ during overdischarging was also observed. Moreover, the insertion/extraction reaction was experimentally shown to be accompanied by a series of cation redistributions in the spinel framework, which were further supported by density functional theory calculations. The inverted Mn is believed to be directly involved in the cation migrations, which would cause voltage hysteresis and irreversible structural evolution after overdischarging. Tuning the Mg/Mn inversion rate could provide a direct path to further optimize spinel oxide cathodes for Mg-ion batteries, and more generally, the operando techniques developed in this work should play a key role in understanding the complex mechanisms involved in multivalent ion insertion systems.

Effect of Passivating Shells on the Chemistry and Electrode Properties of LiMn2O4 Nanocrystal Heterostructures.

Building a stable chemical environment at the cathode/electrolyte interface is directly linked to the durability of Li-ion batteries with high energy density. Recently, colloidal chemistry methods have enabled the design of core-shell nanocrystals of Li1+ xMn2- xO4, an important battery cathode, with passivating shells rich in Al3+ through a colloidal synthetic route. These heterostructures combine the presence of redox-inactive ions on the surface to minimize undesired reactions, with the coverage of each individual particle in an epitaxial manner. Although they improve electrode performance, the exact chemistry and structure of the shell as well as the precise effect of the ratio between the shell and the active core remain to be elucidated. Correlation of these parameters to electrode properties would serve to tailor the heterostructure design toward complete shutdown of undesired reactions. These knowledge gaps are the target of this study. Li1+ xMn2- xO4 nanocrystals with Al3+-rich shells of different thicknesses were synthesized. Multimodal characterization comprehensively revealed the elemental distribution, electronic state, and crystallinity in the heterostructures, which confirmed the potential of this approach to finely tune passivating layers. All of the modified nanocrystals improved the capacity retention while retaining charge storage compared to the bare counterpart, even under harsh conditions.

Nanocrystal heterostructures of LiCoO2 with conformal passivating shells.

Stabilization of electrode-electrolyte interfaces is required to increase the energy stored in battery electrodes. Introducing redox-inactive ions on the electrode surface minimizes deleterious side reactions without affecting the bulk properties. A synthetic challenge exists to grow such layers conformally at each primary particle, to fully passivate interfaces that are buried in the final electrode architecture. The development of methods of sequential colloidal growth of complex oxides and overlayers, enabled by surfactant interactions, would provide novel means to advance toward this goal. Here, nanocrystals composed of LiCoO2, a commercially relevant material for high energy devices, were grown with a shell enriched in Al3+, deposited conformally through a one-pot colloidal synthetic method. The effects of synthetic conditions on the composition of the Al-rich shell and the corresponding electrochemical performance were investigated. The modified nanocrystals showed enhanced electrochemical properties, while maintaining carrier transport.

Mechanisms of Degradation and Strategies for the Stabilization of Cathode-Electrolyte Interfaces in Li-Ion Batteries.

Undesired reactions at the interface between a transition metal oxide cathode and a nonaqueous electrolyte bring about challenges to the performance of Li-ion batteries in the form of compromised durability. These challenges are especially severe in extreme conditions, such as above room temperature or at high potentials. The ongoing push to increase the energy density of Li-ion batteries to break through the existing barriers of application in electric vehicles creates a compelling need to address these inefficiencies. This goal requires a combination of deep knowledge of the mechanisms underpinning reactivity, and the ability to assemble multifunctional electrode systems where different components synergistically extend cycle life by imparting interfacial stability, while maintaining, or even increasing, capacity and potential of operation. The barriers toward energy storage at high density apply equally in Li-ion, the leading technology in the battery market, and in related, emerging concepts for high energy density, such as Na-ion and Mg-ion, because they also conceptually rely on electroactive transition metal oxides. Therefore, their relevance is broad and the quest for solutions inevitable. In this Account, we describe mechanisms of reaction that can degrade the interface between a Li-ion battery electrolyte and the cathode, based on an oxide with transition metals that can reach high formal oxidation states. The focus is placed on cathodes that deliver high capacity and operate at high potential because their development would enable Li-ion battery technologies with high capacity for energy storage. Electrode-electrolyte instabilities will be identified beyond the intrinsic potential windows of stability, by linking them to the electroactive transition metals present at the surface of the electrode. These instabilities result in irreversible transformations at these interfaces, with formation of insulating layers that impede transport or material loss due to corrosion. As a result, strategies that screen the reactive surface of the oxide, while reducing the transition metal content by introducing inactive ions emerge as a logical means toward interfacial stability. Yet they must be implemented in the form of thin passivating barriers to avoid unacceptable losses in storage capacity. This Account subsequently describes our current ability to build composite structures that include the active material and phases designed to address deleterious reactions. We will discuss emerging strategies that move beyond the application of such barriers on premade agglomerated powders of the material of interest. The need for these strategies will be rationalized by the goal to effectively passivate all interfaces while fully controlling the chemistry that results at the surface and its homogeneity. Such outcomes would successfully minimize interfacial losses, thereby leading to materials that exceed the charge storage and life capabilities possible today. Practically speaking, it would create opportunities to design batteries that break the existing barriers of energy density.

Highly transparent and conducting graphene-embedded ZnO films with enhanced photoluminescence fabricated by aerosol synthesis.

Graphene/inorganic hybrid structures have attracted increasing attention in research aimed at producing advanced optoelectronic devices and sensors. Herein, we report on aerosol synthesis of new graphene-embedded zinc oxide (ZnO) films with higher optical transparency (>80% at visible wavelengths), improved electrical conductivity (>2 orders of magnitude, ∼ 20 kΩ/□), and enhanced photoluminescence (∼ 3 times), as compared to bare ZnO film. The ZnO/graphene composite films, in which reduced graphene oxide nanoplatelets (∼ 4 nm thick) are embedded in nanograined ZnO (∼ 50 nm in grain size), were fabricated from colloidal suspensions of graphene oxide with an aqueous zinc precursor. These new luminescent ZnO/graphene composites, with high optical transparency and improved electrical conductivity, are promising materials for use in optoelectronic devices.

Synthesis and characterization of 3-[131I]iodo-L-tyrosine grafted Fe3O4@SiO2 nanocomposite for single photon emission computed tomography (SPECT) and magnetic resonance imaging (MRI).

In this study, we have successfully developed 3-[131I]iodo-tyrosine grafted Fe3O4@SiO2 nanocomposites for dual potential tumor imaging agent for SPECT and MRI. Fe3O4 nanoparticle was synthesized through thermal decomposition and Fe3O4@SiO2 was prepared by reverse microemulsion method. After conjugating aminopropyltriethoxysiliane, L-tyrosine was introduced by amide coupling reaction. Finally, [131I]iodide was labeled on L-tyrosine grafted Fe3O4@SiO2 nanocomposite by aromatic iodination using chloramine-T.