Quantitative analysis of dental enamel removal during a microabrasion technique

Objetivo: Quantificar, por meio de perfi lometria, a profundidade de esmalte dental removido durante o emprego de uma técnica de microabrasão utilizando-se ácido clorídrico e abrasão manual com espátula plástica. Método: Trinta e seis espécimes obtidos de terceiros molares humanos foram polidos, para obtenção de superfícies planas, e divididos em 3 grupos (n = 12) de acordo com os diferentes tratamentos recebidos: tratamento placebo com água deionizada, como controle negativo (CG); microabrasão com ácido clorídrico a 6.6, OpalustreTM (G1); e ácido clorídrico a 6, Whiteness RMTM (G2). A microabrasão foi realizada, de forma padronizada, submetendo os espécimes a 4 ciclos de 10 segundos cada e abrasão manual utilizando-se uma espátula plástica com carga de 200 g. A perda da superfície de esmalte foi medida após cada um dos ciclos de tratamento por meio de perfi lômetro de contato. Resultados: Após os primeiros 10 segundos de abrasão, já foi encontrada perda de esmalte em ambos os grupos tratados (G1 e G2). Nos grupos G1 e G2, a cada ciclo de 10 segundos, foi observado um aumento signifi cativo na perda de esmalte (p ≤0.05). Após 4 abrasões de 10 segundos cada, as médias de perda de esmalte nos grupos tratados foram 46.04 μm (G1) e 54.65 μm (G2). Foi encontrada uma diferença signifi cativa entre G1 e G2 com relação à perda de esmalte de microabrasão em esmalte dental com segurança, utilizando-se ácido clorídrico e abrasão manual com espátula plástica.

Objective: To quantify, by means of profi lometry, the removal of dental enamel during the use of a microabrasion technique involving the use of hydrochloric acid and manual abrasion with a plastic spatula. Method: Thirty six specimens obtained from human third molars were polished to obtain fl at surfaces and divided into 3 groups (n = 12) according to the different treatments received: A placebo treatment with deionized water as a negative control (CG); microabrasion with 6.6% hydrochloric acid, OpalustreTM (G1); and microabrasion with 6% hydrochloric acid, Whiteness RMTM (G2). The microabrasion was performed in a standardized manner by submitting the specimens to 4 cycles of 10 seconds each and manual abrasion using a plastic spatula (200 g load). The loss of enamel surface was measured after each cycle of treatment by contact profi lometry. Results: Enamel loss was already observed after the fi rst 10 seconds of abrasion with hydrochloric acid in both treated groups (G1 and G2). After 4 abrasions of 10 seconds each, the average fi nal enamel losses in the treated groups were 46.04 μm (G1) and 54.65 μm (G2). In the G1 and G2 groups, a signifi cant increase in enamel wear was detected in each cycle in comparison to the control group (p ≤ 0.05). A signifi cant difference in enamel loss between G1 and G2 was found after 30 and 40 seconds of microabrasion. Relevance: The results of this study provide objective data for safely performing the microabrasion technique on dental enamel using hydrochloric acid and manual abrasion using a plastic spatula.

Protective effect of CO2 laser (10.6 µm) and fluoride on enamel erosion in vitro.

The aim of this study was to analyze the effect of CO(2) laser (10.6 µm) irradiation with 5-µs pulse width in prevention of enamel erosion due to citric acid exposure in vitro. One hundred forty-four bovine enamel samples were cut into 5 × 5 × 2-mm-size slabs and polished to obtain plane surfaces. Enamel surfaces were covered with acid-resistant varnish, except for a central area of 2.5 mm in diameter. The samples were divided into four groups (n = 12/group/day): C-control, no treatment; L-CO(2) laser irradiation (0.3 J/cm(2), 5 µs, 226 Hz); F-topical fluoride treatment, 1.25%F(-) (AmF/NaF) for 3 min; and FL-fluoride treatment + CO(2) laser. For erosive demineralization, samples were immersed in 40 ml of citric acid (0.05 M, pH 2.3) for 20 min two times per day during 5 days. After 1, 3, and 5 days, surface loss was measured by digital profilometer. According to the repeated measure ANOVA and post hoc comparisons, all the treatments showed statistically significant reduction of enamel loss as compared to control group, in all investigated times (p < 0.0001): L (52%,31%,37%); F (28%,24%,29%); FL (73%,55%,57%). Both CO(2) laser irradiation alone (L) and the combined laser-fluoride treatment (FL) caused less enamel loss than the fluoride group (F) in all days (p < 0.0001 for L in all times; and p < 0.0001, p = 0.0220 and p = 0.0051 for F, respectively, at days 1, 3, and 5). Under the conditions of this study, CO(2) laser irradiation (0.3 J/cm(2), 5 µs, 226 Hz) could effectively reduce enamel surface loss due to citric acid exposure, in vitro. This effect was still observed after 5 days of repeated acid exposures.

Precise ablation of dental hard tissues with ultra-short pulsed lasers. Preliminary exploratory investigation on adequate laser parameters.

This study aimed to evaluate the possibility of introducing ultra-short pulsed lasers (USPL) in restorative dentistry by maintaining the well-known benefits of lasers for caries removal, but also overcoming disadvantages, such as thermal damage of irradiated substrate. USPL ablation of dental hard tissues was investigated in two phases. Phase 1--different wavelengths (355, 532, 1,045, and 1,064 nm), pulse durations (picoseconds and femtoseconds) and irradiation parameters (scanning speed, output power, and pulse repetition rate) were assessed for enamel and dentin. Ablation rate was determined, and the temperature increase measured in real time. Phase 2--the most favorable laser parameters were evaluated to correlate temperature increase to ablation rate and ablation efficiency. The influence of cooling methods (air, air-water spray) on ablation process was further analyzed. All parameters tested provided precise and selective tissue ablation. For all lasers, faster scanning speeds resulted in better interaction and reduced temperature increase. The most adequate results were observed for the 1064-nm ps-laser and the 1045-nm fs-laser. Forced cooling caused moderate changes in temperature increase, but reduced ablation, being considered unnecessary during irradiation with USPL. For dentin, the correlation between temperature increase and ablation efficiency was satisfactory for both pulse durations, while for enamel, the best correlation was observed for fs-laser, independently of the power used. USPL may be suitable for cavity preparation in dentin and enamel, since effective ablation and low temperature increase were observed. If adequate laser parameters are selected, this technique seems to be promising for promoting the laser-assisted, minimally invasive approach.