Development and experimental validation of a dynamic numerical model for human articular cartilage.

The purpose of this study was to create a preliminary set of experimentally validated Finite Element Analysis (FEA) models, in order to predict the dynamic mechanical behaviour of human articular cartilage (AC). Current models consider static loading with limited independent experimental validation, while the models for this study assess dynamic loading of AC, with direct comparison and validation to physical testing. Three different FEA models of AC were constructed, which considered both linear elastic and hyperelastic models; Neo-Hookean and Ogden. Models were validated using the data collected from compression testing of human femoral heads across 0-1.7 MPa (quasi-static tests and dynamic mechanical analysis). The linear elastic model was inadequate, with a 10-fold over prediction of the displacement dynamic amplitude. The Neo-Hookean model accurately predicted the dynamic amplitude but failed to predict the initial compression of the cartilage, with a 10 times overprediction. The Ogden model provided the best results, with both the initial compression lying within one standard deviation of that observed in the validation data set, and the dynamic amplitude of the same order of magnitude. In conclusion, this study has found that the fast dynamic response of human AC is best represented by a third order Ogden model.

Analysis of hydration and subchondral bone density on the viscoelastic properties of bovine articular cartilage.

BACKGROUND: Articular cartilage is known to be a viscoelastic material, however little research has explored the impact of cartilage water content and bone density on its viscoelasticity. This study aimed to isolate subchondral bone density and hydration of articular cartilage and analyse their effects on the viscoelastic properties of articular cartilage. METHODS: Dynamic mechanical analysis was used to test samples at frequencies of 1, 8, 12, 29, 49, 71, and 88 Hz. Synthetic bone material with densities of 663.7 kg/m3 and 156.8 kg/m3 were used to mimic the bone mineral density (BMD). Dehydration occurred in a stepwise manner at relative humidity (RH) levels of 100%, 30%, and 1%. These relative humidity levels led to water contents of approximately 76%, 8.5%, and ≈ 0% by mass, respectively. RESULTS: Samples from eight bovine femoral heads were tested under a sinusoidal load. Storage stiffness was lower on the lower substrate density. Storage stiffness, though, increased as cartilage samples were dehydrated from a water content of 76% to 8.5%; decreasing again as the water content was further reduced. Loss stiffness was lower on a lower density substrate and decreased as the water content decreased. CONCLUSIONS: In conclusions, a decrease in hydration decreases the loss stiffness, but a non-linear relationship between hydration and storage stiffness may exist. Additionally, higher BMD values led to greater storage and loss stiffnesses.

Implementation of Critical Care Response Teams in Ontario: Impact on the Outcomes of Surgical Patients.

OBJECTIVE: To evaluate whether introduction of CCRTs reduced mortality rates among patients who developed a postoperative complication, also referred to as FTR. BACKGROUND: CCRTs were introduced to improve patients' postoperative outcomes. Its effect on FTR continues to be actively investigated. METHODS: We conducted a population-based retrospective cohort study using administrative data from Ontario, Canada. We identified 810,279 patients admitted to hospital for major surgical procedures between January 2004 and December 2014, with a washout period consisting of the 9 months before and after the implementation of CCRTs in January 2007. Difference-in-differences analysis among patients who developed a postoperative complication (n = 148,882) was used to estimate the association between CCRT implementation and FTR before and after CCRT implementation in hospitals that did - versus did not - implement CCRT during the study period. RESULTS: A total of 810,279 patients were included, of whom 148,882 (18.4%) developed a postoperative surgical complication. Among patients who developed a postoperative complication, the overall proportion of FTR was 9.2% (n = 13,659). Among patients in hospitals that introduced CCRT, the RR of FTR was 0.84, [95% confidence interval (CI) 0.78-0.90] after implementation of CCRT, while over the same time period, the RR was 0.85 (95% CI 0.80-0.91) in hospitals that did not implement CCRT. The RR ratio (difference-indifferences) was 0.99 (95% CI 0.89-1.09). Among patients undergoing orthopedic surgery, the RR ratio was 0.84 (95% CI 0.75-0.95). CONCLUSION: Although implementation of CCRTs in hospitals in Ontario, Canada, did not reduce FTR among all surgical patients having surgery, CCRTs may reduce the risk of FTR among patients having orthopedic surgery.

The effect of injurious compression on the elastic, hyper-elastic and visco-elastic properties of porcine peripheral nerves.

The aim of this study was to characterise the viscoelastic and hyper-elastic properties of the ulnar nerve before and after compression has been induced, in order to aid the understanding of how the mechanical properties of nerves are altered during nerve compression, a contributing factor to cubital tunnel syndrome. Ulnar nerves were dissected from porcine legs and tensile tested to 10% strain. The Young's modulus and Yeoh hyper-elastic model were used to evaluate the materials elastic and hyper-elastic properties respectively. Dynamic mechanical analysis (DMA) was used to evaluate the viscoelastic properties over a range of frequencies between 0.5 Hz and 38 Hz. The nerves were then compressed to 40% for 60 s and the same tests were carried out after compression. The nerves were stiffer after compression, the mean Young's modulus before was 0.181 MPa and increased to 0.601 MPa after compression. The mean shear modulus calculated from the Yeoh hyper-elastic model was also higher after compression increasing from 5 kPa to 7 kPa. After compression, these properties had significantly increased (p < 0.05). The DMA results showed that the nerves exhibit frequency dependent viscoelastic behaviour across all tested frequencies. The median values of storage modulus before compression ranged between 0.605 and 0.757 MPa across the frequencies and after compression between 1.161 MPa and 1.381 MPa. There was a larger range of median values for loss modulus, before compression, median values ranged between 0.073 MPa and 0.216 MPa and after compression from 0.165 MPa to 0.410 MPa. There was a significant increase in both storage and loss modulus after compression (p < 0.05). The mechanical properties of the nerve change following compression, however the response to decompression in vivo requires further evaluation to determine whether the observed changes persist, which may have implications for clinical recovery after surgical decompression in entrapment neuropathy.

Mechanical testing of glutaraldehyde cross-linked mitral valves. Part one: In vitro mechanical behaviour.

The aim of this study was to perform an initial assessment, in vitro, of the feasibility of using a glutaraldehyde cross-linked porcine mitral valve to retain acute functionality, focusing on assessing mitral regurgitation. Six porcine hearts were tested using an in vitro simulator. Testing was repeated following cross-linking of mitral valves; where cross-linking was achieved by placing them in a glutaraldehyde solution. The simulator enabled systolic pressure on the ventricular side of the valve to be mimicked. Following testing, mitral valve leaflets underwent Scanning Electron Microscopy of the ventricular surface of both the anterior and posterior leaflets (1 cm2 samples). The peak pressure withstood by cross-linked valves was significantly lower than for untreated valves (108 mmHg cf. 128 mmHg for untreated valves; p < 0.05). The peak pressure was typically reached 0.5 s later than for the untreated valve. While both cross-linked and untreated valves exhibited endothelium denudation, the unfixed valve had less endothelial loss. Glutaraldehyde cross-linking of porcine mitral valves may be of potential value in assessing improved bioprosthetic mitral valve replacements. However, a more immobile valve exhibiting endothelial denudation (i.e. sclerosis) was a possible concerns identified following in vitro acute assessment.

Mechanical testing of glutaraldehyde cross-linked mitral valves. Part two: Elastic and viscoelastic properties of chordae tendineae.

The aim of this study was to assess whether the mechanical properties of mitral valve chordae tendineae are sensitive to being cross-linked under load. A total 64 chordae were extracted from eight porcine hearts. Two chordae (posterior basal) from each heart were subjected to uniaxial ramp testing and six chordae (two strut, two anterior basal and two posterior basal) were subjected to dynamic mechanical analysis over frequencies between 0.5 and 10 Hz. Chordae were either cross-linked in tension or cross-linked in the absence of loading. Chordae cross-linked under load transitioned from high to low extension at a lower strain than cross-linked unloaded chordae (0.07 cf. 0.22), with greater pre-transitional (30.8 MPa cf. 5.78 MPa) and post-transitional (139 MPa cf. 74.1 MPa) moduli. The mean storage modulus of anterior strut chordae ranged from 48 to 54 MPa for cross-linked unloaded chordae, as compared to 53-61 MPa cross-linked loaded chordae. The mean loss modulus of anterior strut chordae ranged from 2.3 to 2.9 MPa for cross-linked unloaded chordae, as compared to 3.8-4.8 MPa cross-linked loaded chordae. The elastic and viscoelastic properties of chordae following glutaraldehyde cross-linking are dependent on the inclusion/exclusion of loading during the cross-linking process; with loading increasing the magnitude of the material properties measured.

Dynamic viscoelastic characterisation of human osteochondral tissue: understanding the effect of the cartilage-bone interface.

BACKGROUND: Despite it being known that subchondral bone affects the viscoelasticity of cartilage, there has been little research into the mechanical properties of osteochondral tissue as a whole system. This study aims to unearth new knowledge concerning the dynamic behaviour of human subchondral bone and how energy is transferred through the cartilage-bone interface. METHODS: Dynamic mechanical analysis was used to determine the frequency-dependent (1-90 Hz) viscoelastic properties of the osteochondral unit (cartilage-bone system) as well as isolated cartilage and bone specimens extracted from human femoral heads obtained from patients undergoing total hip replacement surgery, with a mean age of 78 years (N = 5, n = 22). Bone mineral density (BMD) was also determined for samples using micro-computed tomography as a marker of tissue health. RESULTS: Cartilage storage and loss moduli along with bone storage modulus were found to increase logarithmically (p < 0.05) with frequency. The mean cartilage storage modulus was 34.4 ± 3.35 MPa and loss modulus was 6.17 ± 0.48 MPa (mean ± standard deviation). In contrast, bone loss modulus decreased logarithmically between 1 and 90 Hz (p < 0.05). The storage stiffness of the cartilage-bone-core was found to be frequency-dependent with a mean value of 1016 ± 54.0 N.mm- 1, while the loss stiffness was determined to be frequency-independent at 78.84 ± 2.48 N.mm- 1. Notably, a statistically significant (p < 0.05) linear correlation was found between the total energy dissipated from the isolated cartilage specimens, and the BMD of the isolated bone specimens at all frequencies except at 90 Hz (p = 0.09). CONCLUSIONS: The viscoelastic properties of the cartilage-bone core were significantly different to the tissues in isolation (p < 0.05). Results from this study demonstrate that the functionality of these tissues arises because they operate as a unit. This is evidenced through the link between cartilage energy dissipated and bone BMD. The results may provide insights into the functionality of the osteochondral unit, which may offer further understanding of disease progression, such as osteoarthritis (OA). Furthermore, the results emphasise the importance of studying human tissue, as bovine models do not always display the same trends.

The design of additively manufactured lattices to increase the functionality of medical implants.

The rise of antibiotic resistant bacterial species is driving the requirement for medical devices that minimise infection risks. Antimicrobial functionality may be achieved by modifying the implant design to incorporate a reservoir that locally releases a therapeutic. For this approach to be successful it is critical that mechanical functionality of the implant is maintained. This study explores the opportunity to exploit the design flexibilities possible using additive manufacturing to develop porous lattices that maximise the volume available for drug loading while maintaining load-bearing capacity of a hip implant. Eight unit cell types were initially investigated and a volume fraction of 30% was identified as the lowest level at which all lattices met the design criteria in ISO 13314. Finite element analysis (FEA) identified three lattice types that exhibited significantly lower displacement (10-fold) compared with other designs; Schwartz primitive, Schwartz primitive pinched and cylinder grid. These lattices were additively manufactured in Ti-6Al-4V using selective laser melting. Each design exceeded the minimum strength requirements for orthopaedic hip implants according to ISO 7206-4. The Schwartz primitive (Pinched) lattice geometry, with 10% volume fill and a cubic unit cell period of 10, allowed the greatest void volume of all lattice designs whilst meeting the fatigue requirements for use in an orthopaedic implant (ISO 7206-4). This paper demonstrates an example of how additive manufacture may be exploited to add additional functionality to medical implants.

Towards viscoelastic characterisation of the human ulnar nerve: An early assessment using embalmed cadavers.

Cubital tunnel syndrome is the most prevalent neuropathy of the ulnar nerve and its aetiology is controversial. Potential replacement materials should display similar viscoelastic properties. The purpose of this study was to assess the feasibility and merit of quantifying the frequency-dependent viscoelastic properties of proximal and distal sections of the human ulnar nerve. Four ulnar nerves (n = 4) were dissected from the elbows of human cadavers and sectioned at the level of the cubital tunnel into proximal and distal sections. These eight sections of the ulnar nerve were sinusoidally loaded to induce stresses between 0.05 and 0.27 MPa and the viscoelastic properties were measured between 0.5 and 24 Hz using dynamic mechanical analysis. The nerves were found to exhibit frequency-dependent viscoelastic behaviour throughout this frequency range. The median storage moduli of the proximal nerves ranged between 7.03 and 8.18 MPa, and 8.85-10.19 MPa for distal nerves, over the frequency-sweep tested. The median loss moduli of the proximal nerves ranged between 0.46 and 0.81 MPa and between 0.51 and 0.80 MPa for distal nerves. Ulnar nerves display frequency dependency viscoelasticity. Such characterisation is feasible with potential applications to suitable nerve grafts.

Matrix degradation in osteoarthritis primes the superficial region of cartilage for mechanical damage.

Osteoarthritis (OA) is a degenerative disease that affects 25% of the world's population over fifty years of age. It is a chronic disease of the synovial joints, primarily the hip and knee. The main pathologies are degradation of the articular cartilage and changes to the subchondral bone, as a result of both mechanical wear and a locally elevated inflammatory state. This study compares the viscoelastic properties of cartilage that represents the biochemical changes in OA and age-matched healthy tissue. Further, the mechanical damage induced by this compressive loading cycle was characterised and the mechanism for it was investigated. The storage modulus of OA cartilage was shown to be significantly lower than that of healthy cartilage whilst having a higher capacity to hold water. Following mechanical testing, there was a significant increase in the surface roughness of OA cartilage. This change in surface structure occurred following a reduction in sulphated glycosaminoglycan content of the superficial region in OA, as seen by alcian blue staining and quantified by micro X-ray fluorescence. These findings are important in understanding how the chemical changes to cartilage matrix in OA influence its dynamic mechanical properties and structural integrity. STATEMENT OF SIGNIFICANCE: Cartilage has a very specialised tissue structure which acts to resist compressive loading. In osteoarthritis (OA), there is both mechanically- and chemically-induced damage to cartilage, resulting in severe degradation of the tissue. In this study we have undertaken a detailed mechanical and chemical analysis of macroscopically undamaged OA and healthy cartilage tissue. We have demonstrated, for the first time in human tissue, that the mechanical degradation of the tissue is attributed to a chemical change across the structure. In macroscopically undamaged OA tissue, there is a reduction in the elastic response of cartilage tissue and an associated destabilisation of the matrix that leaves it susceptible to damage. Understanding this allows us to better understand the progression of OA to design better therapeutic interventions.

Hyperspectral chemical imaging reveals spatially varied degradation of polycarbonate urethane (PCU) biomaterials.

Hyperspectral chemical imaging (HCI) is an emerging technique which combines spectroscopy with imaging. Unlike traditional point spectroscopy, which is used in the majority of polymer biomaterial degradation studies, HCI enables the acquisition of spatially localised spectra across the surface of a material in an objective manner. Here, we demonstrate that attenuated total reflectance Fourier transform infra-red (ATR-FTIR) HCI reveals spatial variation in the degradation of implantable polycarbonate urethane (PCU) biomaterials. It is also shown that HCI can detect possible defects in biomaterial formulation or specimen production; these spatially resolved images reveal regional or scattered spatial heterogeneity. Further, we demonstrate a map sampling method, which can be used in time-sensitive scenarios, allowing for the investigation of degradation across a larger component or component area. Unlike imaging, mapping does not produce a contiguous image, yet grants an insight into the spatial heterogeneity of the biomaterial across a larger area. These novel applications of HCI demonstrate its ability to assist in the detection of defective manufacturing components and lead to a deeper understanding of how a biomaterial's chemical structure changes due to implantation. STATEMENT OF SIGNIFICANCE: The human body is an aggressive environment for implantable devices and their biomaterial components. Polycarbonate urethane (PCU) biomaterials in particular were investigated in this study. Traditionally one or a few points on the PCU surface are analysed using ATR-FTIR spectroscopy. However the selection of acquisition points is susceptible to operator bias and critical information can be lost. This study utilises hyperspectral chemical imaging (HCI) to demonstrate that the degradation of a biomaterial varies spatially. Further, HCI revealed spatial variations of biomaterials that were not subjected to oxidative degradation leading to the possibility of HCI being used in the assessment of biomaterial formulation and/or component production.

Formulation and viscoelasticity of mineralised hydrogels for use in bone-cartilage interfacial reconstruction.

Articular cartilage is a viscoelastic tissue whose structural integrity is important in maintaining joint health. To restore the functionality of osteoarthritic joints it is vital that regenerative strategies mimic the dynamic loading response of cartilage and bone. Here, a rotating simplex model was employed to optimise the composition of agarose and gellan hydrogel constructs structured with hydroxyapatite (HA) with the aim of obtaining composites mechanically comparable to human cartilage in terms of their ability to dissipate energy. Addition of ceramic particles was found to reinforce both matrices up to a critical concentration (< 3w/v%). Beyond this, larger agglomerates were formed, as evidenced by micro computed tomography data, which acted as stress risers and reduced the ability of composites to dissipate energy demonstrated by a reduction in tan δ values. A maximum compressive modulus of 450.7±24.9 kPa was achieved with a composition of 5.8w/v% agarose and 0.5w/v% HA. Interestingly, when loaded dynamically (1-20Hz) this optimised formulation did not exhibit the highest complex modulus instead a sample with a higher concentration of mineral was identified (5.8w/v% agarose and 25w/v% HA). Thus, demonstrating the importance of examining the mechanical behaviour of biomaterials under conditions representative of physiological environments. While the complex moduli of the optimised gellan (1.0 ± 0.2MPa at 1Hz) and agarose (1.7 ± 0.2MPa at 1Hz) constructs did not match the complex moduli of healthy human cartilage samples (26.3 ± 6.5MPa at 1Hz), similar tan δ values were observed between 1 and 5Hz. This is promising since these frequencies represent the typical heel strike time of the general population. In summary, this study demonstrates the importance of considering more than just the strength of biomaterials since tissues like cartilage play a more complex role.

In vitro oxidative degradation of a spinal posterior dynamic stabilization device.

This study quantified the changes of the frequency-dependant viscoelastic properties of the BDyn (S14 Implants, Pessac, France) spinal posterior dynamic stabilization (PDS) device due to in vitro oxidation. Six polycarbonate urethane (PCU) rings and six silicone cushions were degraded using a 20% hydrogen peroxide/0.1 M cobalt (II) chloride hexahydrate, at 37°C, for 24 days. The viscoelastic properties of the individual components and the components assembled into the BDyn PDS device were determined using Dynamic Mechanical Analysis at frequencies from 0.01 to 30 Hz. Attenuated Total Reflectance Fourier Transform Infra-Red spectra demonstrated chemical structure changes, of the PCU, associated with oxidation while Scanning Electron Microscope images revealed surface pitting. No chemical structure or surface morphology changes were observed for the silicone cushion. The BDyn device storage and loss stiffness ranged between 84.46 N/mm to 99.36 N/mm and 8.13 N/mm to 21.99 N/mm, respectively. The storage and loss stiffness for the components and BDyn device increased logarithmically with respect to frequency. Viscoelastic properties, between normal and degraded components, were significantly different for specific frequencies only. This study demonstrates the importance of analyzing changes of viscoelastic properties of degraded biomaterials and medical devices into which they are incorporated, using a frequency sweep. © 2017 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 106B: 1237-1244, 2018.

Viscoelasticity of articular cartilage: Analysing the effect of induced stress and the restraint of bone in a dynamic environment.

The aim of this study was to determine the effect of the induced stress and restraint provided by the underlying bone on the frequency-dependent storage and loss stiffness (for bone restraint) or modulus (for induced stress) of articular cartilage, which characterise its viscoelasticity. Dynamic mechanical analysis has been used to determine the frequency-dependent viscoelastic properties of bovine femoral and humeral head articular cartilage. A sinusoidal load was applied to the specimens and out-of-phase displacement response was measured to determine the phase angle, the storage and loss stiffness or modulus. As induced stress increased, the storage modulus significantly increased (p < 0.05). The phase angle decreased significantly (p < 0.05) as the induced stress increased; reducing from 13.1° to 3.5°. The median storage stiffness ranged from 548N/mm to 707N/mm for cartilage tested on-bone and 544N/mm to 732N/mm for cartilage tested off-bone. On-bone articular cartilage loss stiffness was frequency independent (p > 0.05); however, off-bone, articular cartilage loss stiffness demonstrated a logarithmic frequency-dependency (p < 0.05). In conclusion, the frequency-dependent trends of storage and loss moduli of articular cartilage are dependent on the induced stress, while the restraint provided by the underlying bone removes the frequency-dependency of the loss stiffness.

Epilepsy: Transition from pediatric to adult care. Recommendations of the Ontario epilepsy implementation task force.

The transition from a pediatric to adult health care system is challenging for many youths with epilepsy and their families. Recently, the Ministry of Health and Long-Term Care of the Province of Ontario, Canada, created a transition working group (TWG) to develop recommendations for the transition process for patients with epilepsy in the Province of Ontario. Herein we present an executive summary of this work. The TWG was composed of a multidisciplinary group of pediatric and adult epileptologists, psychiatrists, and family doctors from academia and from the community; neurologists from the community; nurses and social workers from pediatric and adult epilepsy programs; adolescent medicine physician specialists; a team of physicians, nurses, and social workers dedicated to patients with complex care needs; a lawyer; an occupational therapist; representatives from community epilepsy agencies; patients with epilepsy; parents of patients with epilepsy and severe intellectual disability; and project managers. Three main areas were addressed: (1) Diagnosis and Management of Seizures; 2) Mental Health and Psychosocial Needs; and 3) Financial, Community, and Legal Supports. Although there are no systematic studies on the outcomes of transition programs, the impressions of the TWG are as follows. Teenagers at risk of poor transition should be identified early. The care coordination between pediatric and adult neurologists and other specialists should begin before the actual transfer. The transition period is the ideal time to rethink the diagnosis and repeat diagnostic testing where indicated (particularly genetic testing, which now can uncover more etiologies than when patients were initially evaluated many years ago). Some screening tests should be repeated after the move to the adult system. The seven steps proposed herein may facilitate transition, thereby promoting uninterrupted and adequate care for youth with epilepsy leaving the pediatric system.

Viscoelastic properties of human and bovine articular cartilage: a comparison of frequency-dependent trends.

BACKGROUND: The purpose of this study was to compare the frequency-dependent viscoelastic properties of human and bovine cartilage. METHODS: Full-depth cartilage specimens were extracted from bovine and human femoral heads. Using dynamic mechanical analysis, the viscoelastic properties of eight bovine and six human specimens were measured over the frequency range 1 Hz to 88 Hz. Significant differences between bovine and human cartilage viscoelastic properties were assessed using a Mann-Whitney test (p < 0.05). RESULTS: Throughout the range of frequencies tested and for both species, the storage modulus was greater than the loss modulus and both were frequency-dependent. The storage and loss moduli of all human and bovine cartilage specimens presented a logarithmic relationship with respect to frequency. The mean human storage modulus ranged from 31.9 MPa to 43.3 MPa, while the mean bovine storage modulus ranged from 54.0 MPa to 80.5 MPa; bovine storage moduli were 1.7 to 1.9 times greater than the human modulus. Similarly, the loss modulus of bovine cartilage was 2.0 to 2.1 times greater than human. The mean human loss modulus ranged from 5.3 MPa to 8.5 MPa while bovine moduli ranged from 10.6 MPa to 18.1 MPa. CONCLUSION: Frequency-dependent viscoelastic trends of bovine articular cartilage were consistent with those of human articular cartilage; this includes a similar frequency dependency and high-frequency plateau. Bovine cartilage was, however, 'stiffer' than human by a factor of approximately 2. With these provisos, bovine articular cartilage may be a suitable dynamic model for human articular cartilage.

Viscoelastic properties of a spinal posterior dynamic stabilisation device.

The purpose of this study was to quantify the frequency dependent viscoelastic properties of two types of spinal posterior dynamic stabilisation devices. In air at 37°C, the viscoelastic properties of six BDyn 1 level, six BDyn 2 level posterior dynamic stabilisation devices (S14 Implants, Pessac, France) and its elastomeric components (polycarbonate urethane and silicone) were measured using Dynamic Mechanical Analysis. The viscoelastic properties were measured over the frequency range 0.01-30Hz. The BDyn devices and its components were viscoelastic throughout the frequency range tested. The mean storage stiffness and mean loss stiffness of the BDyn 1 level device, BDyn 2 level device, silicone component and polycarbonate urethane component all presented a logarithmic relationship with respect to frequency. The storage stiffness of the BDyn 1 level device ranged from 95.56N/mm to 119.29N/mm, while the BDyn 2 level storage stiffness ranged from 39.41N/mm to 42.82N/mm. BDyn 1 level device and BDyn 2 level device loss stiffness ranged from 10.72N/mm to 23.42N/mm and 4.26N/mm to 9.57N/mm, respectively. No resonant frequencies were recorded for the devices or its components. The elastic property of BDyn 1 level device is influenced by the PCU and silicone components, in the physiological frequency range. The viscoelastic properties calculated in this study may be compared to spinal devices and spinal structures.

Critical care capacity in Canada: results of a national cross-sectional study.

INTRODUCTION: Intensive Care Units (ICUs) provide life-supporting treatment; however, resources are limited, so demand may exceed supply in the event of pandemics, environmental disasters, or in the context of an aging population. We hypothesized that comprehensive national data on ICU resources would permit a better understanding of regional differences in system capacity. METHODS: After the 2009-2010 Influenza A (H1N1) pandemic, the Canadian Critical Care Trials Group surveyed all acute care hospitals in Canada to assess ICU capacity. Using a structured survey tool administered to physicians, respiratory therapists and nurses, we determined the number of ICU beds, ventilators, and the ability to provide specialized support for respiratory failure. RESULTS: We identified 286 hospitals with 3170 ICU beds and 4982 mechanical ventilators for critically ill patients. Twenty-two hospitals had an ICU that routinely cared for children; 15 had dedicated pediatric ICUs. Per 100,000 population, there was substantial variability in provincial capacity, with a mean of 0.9 hospitals with ICUs (provincial range 0.4-2.8), 10 ICU beds capable of providing mechanical ventilation (provincial range 6-19), and 15 invasive mechanical ventilators (provincial range 10-24). There was only moderate correlation between ventilation capacity and population size (coefficient of determination (R(2)) = 0.771). CONCLUSION: ICU resources vary widely across Canadian provinces, and during times of increased demand, may result in geographic differences in the ability to care for critically ill patients. These results highlight the need to evolve inter-jurisdictional resource sharing during periods of substantial increase in demand, and provide background data for the development of appropriate critical care capacity benchmarks.