RESUMEN
This study investigated the influence of physical education class (PEC) as an intervention method for aggression, sociality, stress, and physical fitness levels in children from multicultural families. The hypothesis was that participating in PEC would result in reduced aggression and stress and improved sociality and physical fitness in multicultural children. A three-item questionnaire, a body composition test, and physical fitness tests were given three times. Eighty-four subjects were divided into four groups: multicultural children who participated in PEC (multi-PEG, n=12), multicultural children who did not participate in PEC (multi-NPEG, n=13), single-cultural children who participated in PEC (sing-PEG, n=11), and single-cultural children who did not participate in PEC (sing-NPEG, n=12), respectively. Parametric and nonparametric statistical methods were conducted on the collected data with a significance level set a priori at P<0.05. After 8 weeks of PEC, fat mass (F=2.966, P=0.045) and body mass index (F=3.654, P=0.021) had significantly different interaction effects. In the aspect of interaction effects from physical fitness variables, cardiopulmonary endurance (F=21.961, P=0.001), flexibility (F=8.892, P=0.001), muscular endurance (F=31.996, P=0.001), muscular strength (F=4.570, P=0.008), and power (F=24.479, P=0.001) were significantly improved in the multi-PEG compared to those of the other three groups. Moreover, sociality (F=22.144, P=0.001) in the multi-PEG was enhanced, whereas aggression (F=6.745, P=0.001) and stress (F=3.242, P=0.033) levels were reduced. As conclusion, the PEC reduced aggression and stress levels, and improved sociality and physical fitness levels after 8 weeks. This study confirmed that PEC for children from multicultural families can improve psychosocial factors and physical health.
RESUMEN
Most protocols for testing and rehabilitation for recovery and improvement of muscular endurance have been set at 180°/sec, 240°/sec, and 300°/sec. These protocols can cause confusion to clinical providers or other researchers. This study was aimed at investigating the optimal isokinetic angular speed for measuring or developing muscular endurance after assessing the relationship between cardiopulmonary responses and isokinetic moments. This study was conducted with 31 male and female college students. Graded exercise test and body composition were measured as well as the isokinetic moments of the knee muscles at three angular speeds: 180°/sec, 240°/sec, and 300°/sec. The specific isokinetic moments of knee muscles that were measured included: peak torque (PT) and total work (TW) on extensor (e) and flexor (f) of knee joints, which were denoted as ePT180, fPT180, eTW180, fTW180, ePT240, fPT240, eTW240, fTW240, ePT300, fPT300, eTW300, and fTW300 according to the three angular speeds. Spearman correlation test was used to examine the relationship between the sum means of cardiopulmonary responses and the variables of isokinetic moments. This study confirmed that the optimal angular speed for testing or training for muscular endurance was 180°/sec, which showed a stronger relationship between cardiopulmonary responses and isokinetic moments. Therefore, this angular speed is recommended for testing and training for muscular endurance of the knee joints.
RESUMEN
The number of injuries that force golfers to quit is also increasing. In particular, the upper body injuries are concerns for amateur golfers. This study was conducted not only to investigate muscular balance, such as ipsilateral and bilateral ratios of the upper body, but to also evaluate the possible problems of muscular joints in amateur golfers. Male golfers (n=10) and a healthy control group (n=10) were recruited for the assessment of muscular function in the upper body, which was measured by an isokinetic dynamometer at 60°/sec. The tested parts were trunk, wrist, forearm, elbow, and shoulder joints. Mann-Whitney U-test was used to evaluate the significance of the differences between groups. The ipsilateral ratios of peak torque or work per repetition (WR) of trunk flexor and extensor in the golfers were not significantly different compared to those of the control group. These results were similar to the shoulder horizontal abductor and adductor. However, there were significant differences in the ipsilateral and bilateral ratios of the wrist, forearm, and elbow joints. Especially, the WR of the wrist flexor, forearm pronator, and elbow flexor on the left side of amateur golfers showed imbalances in bilateral ratios. Moreover, the WR of the wrist and elbow flexors on the left side of amateur golfers were lower than those of the wrist and elbow extensors. Therefore, amateur golfers should strive to prevent injuries of the wrist, forearm, and elbow joints and to reinforce the endurance on those parts of the left side.
RESUMEN
A fibrovascular polyp is a rare benign disease of the upper digestive tract and is usually located in the esophagus. To our knowledge, this is the first case of gastric fibrovascular polyp presenting with melena reported in the English literature. The polyp was well visualized on endoscopy and removed with laparoscopic wedge resection. Histology confirmed fibrovascular polyp of the stomach.
RESUMEN
Mg-1.0wt%Zn-2.0wt%Y alloy powders were produced by gas atomization, and subsequently sintered by spark plasma sintering (SPS). The SPSed Mg-1.0wt%Zn-2.0wt%Y alloy, which showed a microstructure of well-bonded grains containing nano-sized powders of approximately 100 nm in diameter, was coated by a plasma electrolytic oxidation (PEO) method. Microstructure, mechanical properties and corrosion properties of PEO coatings were investigated and compared to those of normally sintered Mg-1.0wt%Zn-2.0wt%Y and cast Mg-1.0wt%Zn alloys. All coatings consisted of MgO and Mg2SiO4. The micro-hardness and friction coefficient of coatings on the SPSed Mg-1.0wt%Zn-2.0wt%Y alloy were higher than those on normally sintered Mg-1.0wt%Zn-2.0wt%Y and cast Mg-l.0wt%Zn alloys. However, the corrosion resistance in 3.5% NaCl solution for the SPSed Mg-1.0wt%Zn-2.0wt%Y alloy was between that for normally sintered Mg-1.0wt%Zn-2.0wt%Y alloy and cast Mg-1.0wt%Zn alloy.
