RESUMEN
The study examined the correlation between collagen coating damage and self-healing under various tribological conditions. It confirmed that the friction coefficient and degree of damage on the collagen coating varied based on contact and sliding conditions. The friction coefficient, measured at 0.56 for a single sliding cycle under a 350 mN normal load, demonstrated a notable decrease to 0.46 for 2295 cycles under 30 mN, further reducing to 0.15 for 90 cycles under a 20 mN normal load. As the normal load increased, the friction coefficient decreased, and with repeated sliding cycles under the same load, the coefficient also decreased. Water droplets induced a self-healing effect on collagen coating, causing wear tracks to vanish as fibers absorbed water. Severe wear tracks, with broken fibers and peeled coating, showed limited self-healing. In contrast, mild wear tracks, with compressed yet connected fibers, exhibited the self-healing phenomenon, making the wear tracks disappear. Real-time observations during 90 cycles under a 20 mN normal load highlighted the formation of mild wear tracks with intact collagen fibers, providing quantitative insights into self-healing characteristics. To preserve the self-healing effect of the collagen coating, it is essential to ensure tribological conditions during contact and sliding that prevent the disconnection of collagen fibers.
RESUMEN
The association between sleep and pain has been investigated widely. However, inconsistent results from animal studies compared with human data show the need for a validated animal model in the sleep-pain association field. Our study aims to validate common neuropathic pain models as a tool for evaluating the sleep-pain association. Electrodes electroencephalogram (EEG) and electromyogram (EMG) were surgically implanted to measure sleep. The von Frey test was used to measure pain sensitivity. Following the baseline data acquisition, two pain-modelling procedures were performed: sciatic nerve crush injury (SCI) and common peroneal nerve ligation (CPL). Post-injury measurements were performed on days 1, 5, 10, and 15 post-surgery. The results presented decreased paw withdrawal thresholds and reduced NREM sleep duration in both models on the first post-surgery day. In the SCI model, NREM sleep duration was negatively correlated with paw withdrawal thresholds (p = 0.0466), but not in the CPL model. Wake alpha and theta EEG powers were also correlated with the pain threshold. The results confirm that the SCI model shows disturbed sleep patterns associated with increased pain sensitivity, suggesting it is a reliable tool for investigating sleep disturbances associated with neuropathic pain.
RESUMEN
This study investigates the friction and wear characteristics of silicone rubber used in hydraulic systems, focusing on surface properties achieved through coating strategies. Silicone rubber specimens with varying surface characteristics, prepared by coating with micro-sized ceramic particles and employing etching processes, were examined. Surface morphology, roughness, water droplet contact angles, and friction and wear characteristics were evaluated. The silicone rubber was coated with ceramic particles (average size: 16 µm) and subsequently etched for different durations (1, 5, 10, 30, and 60 minutes). The results revealed that longer etching times led to increased surface roughness, while shorter etching times resulted in improved wear characteristics. The friction coefficient demonstrated a discernible reduction with escalating etching durations, with Etching-60M showing approximately 50% lower friction coefficient compared to Etching-1M. Wear rates ranged from 2.47 × 10-7 to 1.43 × 10-6 mm3 N-1 mm-1, indicating an increasing trend with longer etching times. Distinct wear mechanisms were observed between non-etched and etched specimens, with the latter exhibiting more pronounced wear tracks. Finite element analysis highlighted variations in stress behavior during contact sliding, indicating that surface modifications significantly impact wear resistance. While longer etching times improved friction characteristics, shorter etching times yielded superior wear characteristics. Further research is recommended to explore optimal etching conditions considering various variables.
RESUMEN
This research investigates the impact of surface structure on the friction and wear characteristics of silicone rubber used as a material for hydraulic rod seals. Various silicone rubber specimens with different surface structures were prepared, and their surface morphology, water contact angle, and surface roughness were compared. Friction tests were conducted using a reciprocating sliding method to evaluate the friction coefficient and wear characteristics. The results revealed that the silicone rubber specimens coated with silicone powder exhibited a significant increase in surface roughness. However, this increase was accompanied by a decrease in surface energy, leading to the absorption and dispersion of contact pressure and frictional stress, resulting in a friction-reducing effect. Consequently, the silicone rubber specimens coated with silicone powder demonstrated a friction coefficient more than 70% lower on average compared to bare silicone rubber, and exhibited minimal wear characteristics. The irregular microstructures formed on the surface of the silicone rubber are believed to contribute to these friction and wear improvements. Alterations in stress and contact behavior of bare silicone rubber and silicone powder-coated silicone rubber with pre-curing time during indentation and sliding movements were validated through finite element analysis. These findings provide valuable insights for enhancing the performance and durability of hydraulic rod seals made from silicone rubber. This research is expected to contribute to further studies aimed at improving hydraulic seal materials.
RESUMEN
BACKGROUND: Exosomes are extracellular vesicles secreted by eukaryotic cells and have been extensively studied for their surface markers and internal cargo with unique functions. A deeper understanding of exosomes has allowed their application in various research areas, particularly in diagnostics and therapy. MAIN BODY: Exosomes have great potential as biomarkers and delivery vehicles for encapsulating therapeutic cargo. However, the limitations of bare exosomes, such as rapid phagocytic clearance and non-specific biodistribution after injection, pose significant challenges to their application as drug delivery systems. This review focuses on exosome-based drug delivery for treating rheumatoid arthritis, emphasizing pre/post-engineering approaches to overcome these challenges. CONCLUSION: This review will serve as an essential resource for future studies to develop novel exosome-based therapeutic approaches for rheumatoid arthritis. Overall, the review highlights the potential of exosomes as a promising therapeutic approach for rheumatoid arthritis treatment.
RESUMEN
The growing use of plastic materials has resulted in a constant increase in the risk associated with microplastics (MPs). Ultra-violet (UV) light and wind break down modify MPs in the environment into smaller particles known as weathered MPs (WMPs) and these processes increase the risk of MP toxicity. The neurotoxicity of weathered polystyrene-MPs remains unclear. Therefore, it is important to understand the risks posed by WMPs. We evaluated the chemical changes of WMPs generated under laboratory-synchronized environmentally mimetic conditions and compared them with virgin MPs (VMPs). We found that WMP had a rough surface, slight yellow color, reduced molecular weight, and structural alteration compared with those of VMP. Next, 2 µg of â¼100 µm in size of WMP and VMP were orally administered once a day for one week to C57BL/6 male mice. Proteomic analysis revealed that the WMP group had significantly increased activation of immune and neurodegeneration-related pathways compared with that of the VMP group. Consistently, in in vitro experiments, the human brain-derived microglial cell line (HMC-3) also exhibited a more severe inflammatory response to WMP than to VMP. These results show that WMP is a more profound inflammatory factor than VMP. In summary, our findings demonstrate the toxicity of WMPs and provide theoretical insights into their potential risks to biological systems and even humans in the ecosystem.
Asunto(s)
Microplásticos , Contaminantes Químicos del Agua , Animales , Humanos , Ratones , Masculino , Microplásticos/toxicidad , Plásticos , Poliestirenos/toxicidad , Poliestirenos/análisis , Proteoma , Ecosistema , Proteómica , Ratones Endogámicos C57BL , Contaminantes Químicos del Agua/toxicidad , Contaminantes Químicos del Agua/análisis , EncéfaloRESUMEN
Bioactive molecules and their effects have been influenced by their solubility and administration route. In many therapeutic reagents, the performance of therapeutics is dependent on physiological barriers in the human body and delivery efficacy. Therefore, an effective and stable therapeutic delivery promotes pharmaceutical advancement and suitable biological usage of drugs. In the biological and pharmacological industries, lipid nanoparticles (LNPs) have emerged as a potential carrier to deliver therapeutics. Since studies reported doxorubicin-loaded liposomes (Doxil®), LNPs have been applied to numerous clinical trials. Lipid-based nanoparticles, including liposomes, solid lipid nanoparticles (SLNs), and nanostructured lipid nanoparticles, have also been developed to deliver active ingredients in vaccines. In this review, we present the type of LNPs used to develop vaccines with attractive advantages. We then discuss messenger RNA (mRNA) delivery for the clinical application of mRNA therapeutic-loaded LNPs and recent research trend of LNP-based vaccine development.
RESUMEN
The purpose of this study was to improve the tribological properties of polydimethylsiloxane (PDMS) by mixing lubricants into it. The chemical composition, physical/chemical bonding state, and mechanical properties of the PDMS/lubricant composites (PLCs), prepared by mixing PDMS and lubricants at different ratios, were analyzed. With increasing lubricant content, the friction coefficient initially decreased, reaching a minimum value at a PDMS/lubricant ratio of 100 : 10; however, it gradually increased with a further increase in the lubricant content. The mechanical properties of PLCs with lubricant contents of 10% and higher decreased owing to the lubricant addition, so that the contact area with the sliding counter tip increased with lubricant content, but the frictional resistance was still decreased owing to the self-lubricating effect. In addition, owing to the effect of the lubricating film, there was no direct contact between the PLC surface and counter tip, and almost no damage was done to the PLC surface. Finite element analysis of the changes in stress during indentation and sliding confirmed that the stress applied to the PLCs was lower than that for bare PDMS.
RESUMEN
For the past 200 years, lactate has been regarded as a metabolic waste end product that causes fatigue during exercise. However, lactate production is closely correlated with energy metabolism. The lactate dehydrogenase-catalyzed reaction uses protons to produce lactate, which delays ongoing metabolic acidosis. Of note, lactate production differs depending on exercise intensity and is not limited to muscles. Importantly, controlling physiological effect of lactate may be a solution to alleviating some chronic diseases. Released through exercise, lactate is an important biomarker for fat oxidation in skeletal muscles. During recovery after sustained strenuous exercise, most of the lactate accumulated during exercise is removed by direct oxidation. However, as the muscle respiration rate decreases, lactate becomes a desirable substrate for hepatic glucose synthesis. Furthermore, improvement in brain function by lactate, particularly, through the expression of vascular endothelial growth factor and brain-derived neurotrophic factor, is being increasingly studied. In addition, it is possible to improve stress-related symptoms, such as depression, by regulating the function of hippocampal mitochondria, and with an increasingly aging society, lactate is being investigated as a preventive agent for brain diseases such as Alzheimer's disease. Therefore, the perception that lactate is equivalent to fatigue should no longer exist. This review focuses on the new perception of lactate and how lactate acts extensively in the skeletal muscles, heart, brain, kidney, and liver. Additionally, lactate is now used to confirm exercise performance and should be further studied to assess its impact on exercise training.
Asunto(s)
Ácido Láctico , Factor A de Crecimiento Endotelial Vascular , Humanos , Ácido Láctico/metabolismo , Factor A de Crecimiento Endotelial Vascular/metabolismo , Ejercicio Físico/fisiología , Músculo Esquelético/metabolismo , Fatiga/metabolismo , Encéfalo/metabolismoRESUMEN
Polydimethylsiloxane (PDMS) has many advantages, but the friction coefficient generated by contact with the counter material is high. The purpose of this study is to reduce the friction coefficient by forming hierarchical micro/nanopatterns on the PDMS surface using the imprinting method. In addition, the optimum conditions for reducing the friction coefficient by controlling the sliding speed and normal load were determined. After contacting flat bare PDMS and hierarchical micro/nanostructured PDMS with a counter tip made of polyurethane (PU), the change in friction with sliding speed and vertical load was evaluated. Under normal load conditions, the average friction coefficient of the bare PDMS decreased as the sliding speed increased, and that of the patterned PDMS slightly increased. Regardless of the sliding speed, the friction coefficient decreased as the normal load increased for both specimens. At a sliding speed of 4 mm/s under a load of 10 mN, the friction reduction effect of the pattern structure was the largest at 79%. Overall, the greatest friction reduction effect (84%) was confirmed in patterned PDMS with the lowest friction coefficient under the conditions of 4 mm/s, 50 mN, compared to bare PDMS with the highest friction coefficient under the conditions of 4 mm/s, 10 mN.
RESUMEN
Organic electrochemical transistors (OECTs) have become popular due to their advantages of a lower operating voltage and higher transconductance compared with conventional silicon transistors. However, current OECT platform-based skin-inspired electronics applications are limited due to the lack of stretchability in poly(3,4-ethylenedioxythiophene):polystyrene sulfonate (PEDOT:PSS). Some meaningful structural design strategies to resolve this limitation, including rendering OECT to make it more stretchable, have been reported. However, these strategies require complicated fabrication processes and face challenges due to the low areal density of active devices because wavy interconnect parts account for a large area. Nevertheless, there have been only a few reports of fully deformable OECT having skin-like mechanical properties and deformability. In this study, we fabricated stretchable and conductivity-enhanced channel materials using a spray-coating method after a composite solution preparation by blending PEDOT:PSS with several ionic liquids. Among these, the PEDOT composite prepared using 1-butyl-3-methylimidazolium octyl sulfate exhibited a better maximum transconductance value (~0.3 mS) than the other ion composites. When this material was used for our deformable OECT platform using stretchable Au nanomembrane electrodes on an elastomer substrate and an encapsulation layer, our d-ECT showed a barely degraded resistance value between the source and drain during 1000 cycles of a 30% repeated strain. We expect that our d-ECT device will serve as a step toward the development of more precise and accurate biomedical healthcare monitoring systems.
RESUMEN
Physical unclonable function (PUFs) utilize inherent random physical variations of solid-state devices and are a core ingredient of hardware security primitives. PUFs promise more robust information security than that provided by the conventional software-based approaches. While silicon- and memristor-based PUFs are advancing, their reliability and scalability require further improvements. These are currently limited by output fluctuations and associated additional peripherals. Here, highly reliable spintronic PUFs that exploit field-free spin-orbit-torque switching in IrMn/CoFeB/Ta/CoFeB structures are demonstrated. It is shown that the stochastic switching polarity of the perpendicular magnetization of the top CoFeB can be achieved by manipulating the exchange bias directions of the bottom IrMn/CoFeB. This serves as an entropy source for the spintronic PUF, which is characterized by high entropy, uniqueness, reconfigurability, and digital output. Furthermore, the device ensures a zero bit-error-rate under repetitive operations and robustness against external magnetic fields, and offers scalable and energy-efficient device implementations.
RESUMEN
ETHNOPHARMACOLOGICAL RELEVANCE: Patients with dementia are diagnosed with deficiency patterns and interior patterns in traditional Chinese medicine due to decreased physical strength, mental atrophy including cognitive function, and decreased motor function in the gastrointestinal tract. Since "greater yin symptom" in Shanghanlun has been interpreted as interior, deficiency, and cold pattern in traditional Chinese medicine, it is necessary to determine whether Geijigadaehwang-tang (GDT) has therapeutic effects on neurodegenerative diseases and the underlying mechanism if it has such effects. AIMS OF THE STUDY: Trimethyltin (TMT), a neurotoxic organotin compound, has been used to induce several neurodegenerative diseases, including epilepsy and Alzheimer's disease. This study aimed to evaluate the therapeutic efficacy of GDT for TMT-induced hippocampal neurodegeneration and seizures and to determine the mechanisms involved at the molecular level. MATERIALS AND METHODS: The main components of GDT were analyzed using ultra-performance liquid chromatography. TMT was used to induce neurotoxicity in microglial BV-2 cells and C57BL6 mice. GDT was administered at various doses to determine its neuroprotective and seizure inhibition effects. The inhibitory effects of GDT on TMT-induced apoptosis, inflammatory pathways, and oxidative stress pathways were determined in the mouse hippocampal tissues. RESULTS: GDT contained emodin, chrysophanol, albiflorin, paeoniflorin, 6-gingerol, and liquiritin apioside. In microglial BV-2 cells treated with TMT, GDT showed dose-dependent neuroprotective effects. Oral administration of GDT five times for 2.5 days before and after TMT injection inhibited seizures at doses of 180 and 540 mg/kg and inhibited neuronal death in the hippocampus. In hippocampal tissues extracted from mice, GDT inhibited the protein expression of ionized calcium binding adaptor molecule 1, glial fibrillary acidic protein, nucleotide-binding oligomerization domain-like receptor family pyrin domain-containing protein 3, and phosphorylated nuclear factor (NF)-κB/total-NFκB ratio. Additionally, GDT inhibited the messenger RNA levels of tumor necrosis factor-α, inducible nitric oxide synthase, apoptosis-associated speck-like protein containing a caspase recruitment domain, caspase-1, interleukin-1ß, nuclear factor erythroid-2-related factor 2, and heme oxygenase-1. CONCLUSION: This study's results imply that GDT might have neuroprotective potential in neurodegenerative diseases through neuronal death inhibition and anti-inflammatory and antioxidant mechanisms.
Asunto(s)
Enfermedades Neurodegenerativas , Fármacos Neuroprotectores , Animales , Hipocampo , Ratones , Ratones Endogámicos C57BL , FN-kappa B/metabolismo , Enfermedades Neurodegenerativas/inducido químicamente , Enfermedades Neurodegenerativas/tratamiento farmacológico , Fármacos Neuroprotectores/metabolismo , Fármacos Neuroprotectores/farmacología , Fármacos Neuroprotectores/uso terapéutico , Convulsiones/inducido químicamente , Convulsiones/tratamiento farmacológico , Convulsiones/metabolismo , Compuestos de TrimetilestañoRESUMEN
In this study, the friction and wear characteristics of polydimethylsiloxane (PDMS) were evaluated when using lubricants created by adding surfactants at various ratios to deionized (DI) water. When pure DI water is used as a lubricant, the repulsion of water from the hydrophobic PDMS surface is large and the interfacial affinity is low; thus, the lubrication properties cannot be significantly improved. However, when a lubricant with a surfactant is added to DI water, the interfacial affinity with the PDMS surface increases to form a lubricating film, and the friction coefficient is greatly reduced. In this study, under dry and pure DI water conditions, severe wear tracks were formed on the PDMS surface after 10,000 cycles of reciprocating sliding motion under a vertical load of 100 mN, whereas in the case of the surfactant-based and water-based lubricant, no severe wear tracks occurred. The friction and wear characteristics of the PDMS were evaluated by increasing the normal loads and sliding cycles with a water-based lubricant containing 1 wt % surfactant. Under normal loads of 300 mN and 500 mN, only minor scratches occurred on the PDMS surface up to 10,000 and 100,000 cycles, respectively, but after 300,000 cycles, very severe pit wear tracks occurred.
RESUMEN
In this study, we have developed a self-cleaning transparent coating on a glass substrate by dip coating a TiO2 ̶ KH550 ̶ PEG mixed solution with super-hydrophilicity and good antifogging properties. The fabrication of the thin-film-coated glass is a one-step solution blending method that is performed by depositing only one layer of modified TiO2 nanoparticles at room temperature. X-ray diffraction (XRD) and scanning electron microscopy (SEM) were used to determine the structure and morphology of the nanoparticles and the thin-film-coated glass. The surface functional groups were investigated using Fourier-transform infrared spectroscopy (FT-IR), and the optical properties of the glass coating were measured using a UV/Vis spectrometer. The results revealed that the KH-500-modified TiO2 film coating was in an anatase crystalline form. The hydrophilicity of the coated and uncoated glass substrates was observed by measuring their water contact angle (WCA) using a contact angle instrument. The maximum transparency of the coated glass measured in the visible region (380-780 nm) was approximately 70%, and it possessed excellent super-hydrophilic properties (WCA ~0°) at an annealing temperature of 350 °C without further need of UV or plasma treatment. These results demonstrate the super-hydrophilic coated glass surface has potential for use in self-cleaning and anti-fogging applications.
RESUMEN
An electrocorticogram (ECoG) is the electrical activity obtainable from the cerebral cortex and an informative source with considerable potential for future advanced applications in various brain-interfacing technologies. Considerable effort has been devoted to developing biocompatible, conformal, soft, and conductive interfacial materials for bridging devices and brain tissue; however, the implementation of brain-adaptive materials with optimized electrical and mechanical characteristics remains challenging. Herein, we present surface electrode arrays using the soft tough ionic conductive hydrogel (STICH). The newly proposed STICH features brain-adaptive softness with Young's modulus of ~9.46 kPa, which is sufficient to form a conformal interface with the cortex. Additionally, the STICH has high toughness of ~36.85 kJ/mm3, highlighting its robustness for maintaining the solid structure during interfacing with wet brain tissue. The stretchable metal electrodes with a wavy pattern printed on the elastomer were coated with the STICH as an interfacial layer, resulting in an improvement of the impedance from 60 kΩ to 10 kΩ at 1 kHz after coating. Acute in vivo experiments for ECoG monitoring were performed in anesthetized rodents, thereby successfully realizing conformal interfacing to the animal's cortex and the sensitive recording of electrical activity using the STICH-coated electrodes, which exhibited a higher visual-evoked potential (VEP) amplitude than that of the control device.
RESUMEN
The remarkable increase in plastic usage and widespread microplastic (MP) pollution has emerged as a substantial concern today. Many recent studies have revealed MPs as potentially hazardous substances in mammals. Despite several reports on the impact of small MPs in the brain and behaviors in aquatic animals, it is still unclear how small MPs affect the brain and its underlying cellular physiology in terrestrial animals. In this study, we investigated the accumulation of polystyrene MPs (PS-MPs) in mouse brain after oral treatment using three types of fluorescent PS-MPs of different sizes (0.2,2 and 10 µm). We found that PS-MPs were deposited in microglial cells of the brain. Following differential treatment of PS-MPs in human microglial HMC-3 cells, we identified changes in cellular morphology, immune responses, and microglial apoptosis induced by phagocytosis of 0.2 and 2 µm PS-MPs. By analyzing the PS-MP-treated HMC-3 cell transcriptome, we showed that PS-MPs treatment altered the expression of clusters of immune response genes, immunoglobulins, and several related microRNAs. In addition, we confirmed alterations in microglial differentiation marker expression with the activation of NF-κB, pro-inflammatory cytokines and apoptotic markers in PS-MP-treated human microglial cells and in mouse brain. Our findings suggest a potential risk of small PS-MPs in microglial immune activation, which leads to microglial apoptosis in murine and human brains.
Asunto(s)
Microplásticos , Plásticos , Animales , Apoptosis , Ratones , Microglía , Fagocitosis , Poliestirenos/toxicidadRESUMEN
In this study, the friction and wear characteristics of graphene coatings were evaluated using lubricants with various ratios of graphene ink to deionized (DI) water. When dry graphene ink and pure DI water were used as lubricants, the graphene coating initially peeled off, and the friction coefficient rapidly increased to a large value. However, when a lubricant with graphene ink added to DI water was used, a lubricating film was formed on the graphene coating and the friction coefficient was reduced significantly. Under dry and pure DI water conditions, severe wear morphologies were formed on the graphene coating surface, whereas in the case of the lubricant with graphene inks added to DI water, insignificant wear morphologies were formed. When the mixing ratio between DI water and graphene ink was 100:10 and 100:5, the friction coefficient and wear rate were the lowest, respectively. As a result of a long-term experiment in which the sliding cycle was performed for up to 100,000 cycles under the same experimental conditions, the lubricant with a 100:10 mixing ratio showed excellent lubrication properties, confirming that the friction coefficient and wear rate were significantly reduced compared to that of the dry or pure DI water lubrication conditions.
RESUMEN
Glioblastoma multiforme (GBM) is the most aggressive malignant tumor. It is difficult to regulate GBM using conventional chemotherapy-based methods due to its anatomical structure specificity, low drug targeting ability, and limited penetration depth capability to reach the tumor interior. Numerous approaches have been proposed to overcome such issues, including nanoparticle-based drug delivery system (DDS) with the development of GBM site targeting and penetration depth enhancing moieties (e.g., peptides, sugars, proteins, etc.). In this study, we prepared four different types of nanoparticles, which are based on porous silicon nanoparticles (pSiNPs) incorporating polyethylene glycol (PEG), iRGD peptide (well-known cancer targeting peptide), and SIWV tetra-peptide (a recently disclosed GBM-targeting peptide), and analyzed their deep-tumor penetration abilities in cell spheroids, in GBM patient-derived tumoroids, and in GBM xenograft mice. We found that SIWV tetra-peptide significantly enhanced the penetration depth of pSiNPs, and its therapeutic formulation (temozolomide-loaded/SIWV-functionalized pSiNPs) showed a higher anticancer efficacy compared with other formulations. These findings hold great promise for the development of nanotherapeutics and peptide-conjugated drugs for GBM.
Asunto(s)
Glioblastoma , Animales , Línea Celular Tumoral , Glioblastoma/tratamiento farmacológico , Glioblastoma/metabolismo , Glioblastoma/patología , Humanos , Ratones , Péptidos/química , Péptidos/farmacología , Péptidos/uso terapéutico , Polietilenglicoles/química , Polietilenglicoles/uso terapéutico , Silicio/química , Silicio/uso terapéutico , Azúcares/uso terapéutico , Temozolomida/uso terapéuticoRESUMEN
Behavioral stability partially depends on the variability of net outcomes by means of the co-varied adjustment of individual elements such as multi-finger forces. The properties of cyclic actions affect stability and variability of the performance as well as the activation of the prefrontal cortex that is an origin of subcortical structure for the coordinative actions. Little research has been done on the issue of the relationship between stability and neuronal response. The purpose of the study was to investigate the changes in the neural response, particularly at the prefrontal cortex, to the frequencies of isometric cyclic finger force production. The main experimental task was to produce finger forces while matching the produced force to sine-wave templates as accurately as possible. Also, the hemodynamics responses of the prefrontal cortex, including oxy-hemoglobin concentration (ΔHbO) and the functional connectivity, were measured using functional near-infrared spectroscopy. The frequency conditions comprised 0.1, 1, and 2 Hz. The uncontrolled manifold (UCM) approach was applied to compute synergy indices in time-series. The relative phase (RP), the coefficient of variation (CV) of the peak and trough force values were computed as the indices of performance accuracy. The statistical parametric mapping (SPM) was implemented to compare the synergy indices of three frequency conditions in time-series. A less accurate performance in the high-frequency condition was caused not by the RP, but mainly by the inconsistent peak force values (CV; p < 0.01, η p 2 = 0.90). The SPM analysis revealed that the synergy indices were larger in the low-frequency than in high-frequency conditions. Further, the ΔHbO remained unchanged under all frequency conditions, while the functional connectivity decreased with an increase in the frequency of cyclic force production. The current results suggested that the concurrent activation of the prefrontal region mainly depends on the frequency of cyclic force production, which was associated with the strength of stability indices and performance errors. The current study is the first work to uncover the effect of frequency on the multi-finger synergies as to the hemodynamic response in the prefrontal cortex, which possibly provides a clue of the neural mechanism of synergy formation and its changes.