Laponite-Modified Biopolymers as a Conformable Substrate for Optoelectronic Devices.

Biopolymers such as carboxymethyl cellulose and hyaluronic acid are alternative substrates for conformable organic light-emitting diodes (OLEDs). However, drawbacks such as mechanical stress susceptibility can hinder the device's performance under stretched conditions. To overcome these limitations, herein, we developed a nanocomposite based on CMC/HA (carboxymethyl cellulose/hyaluronic acid) and synthetic Laponite, intending to improve the mechanical strength without compromising the film flexibility and transparency (transmittance >80%; 380-700 nm) as substrates for conformable OLEDs. From XRD, FTIR, CP-MAS NMR, and TGA/DTG characterization techniques, it was possible to conclude the presence of Laponite randomly dispersed between the polymer chains. CMC/HA with 5% (w/w) Laponite, CMC/HA 5, presented a higher tensile strength (370.6 MPa) and comparable Young's modulus (51.0 ± 1.2 MPa) in comparison to the nanocomposites and pristine films, indicating a better candidate for the device's substrates. To produce the OLED, the multilayer structure ITO/MoO3/NPB/TCTA:Ir(ppy)3/TPBi:Ir(ppy)3/BPhen/LiF was deposited onto the CMC/HA 5 substrate. The OLEDs fabricated using CMC/HA 5 substrates showed higher luminance (12 kcd/m2) and irradiance (0.9 mW/cm2) values when compared with those based on commercial bacterial cellulose. However, the same device presented a lower efficiency (3.2 cd/A) due to a higher current density. Moreover, the OLED fabricated onto the Laponite-modified biopolymer presented reproducible behavior when submitted to continuous bending stress. Thus, CMC/HA 5 demonstrates potential as a transparent conductor substrate for biopolymer-based OLEDs with comparable performance to commercial bacterial cellulose features.

Review of Bacterial Nanocellulose as Suitable Substrate for Conformable and Flexible Organic Light-Emitting Diodes.

As the development of nanotechnology progresses, organic electronics have gained momentum in recent years, and the production and rapid development of electronic devices based on organic semiconductors, such as organic light-emitting diodes (OLEDs), organic photovoltaic cells (OPVs), and organic field effect transistors (OFETs), among others, have excelled. Their uses extend to the fabrication of intelligent screens for televisions and portable devices, due to their flexibility and versatility. Lately, great efforts have been reported in the literature to use them in the biomedical field, such as in photodynamic therapy. In tandem, there has been considerable interest in the design of advanced materials originating from natural sources. Bacterial nanocellulose (BNC) is a natural polymer synthesized by many microorganisms, notably by non-pathogenic strains of Komagataeibacter (K. xylinus, K. hansenii, and K. rhaeticus). BNC shows distinct physical and mechanical properties, including its insolubility, rapid biodegradability, tensile strength, elasticity, durability, and nontoxic and nonallergenic features, which make BNC ideal for many areas, including active and intelligent food packaging, sensors, water remediation, drug delivery, wound healing, and as conformable/flexible substrates for application in organic electronics. Here, we review BNC production methods, properties, and applications, focusing on electronic devices, especially OLEDs and flexible OLEDs (FOLEDs). Furthermore, we discuss the future progress of BNC-based flexible substrate nanocomposites.

Synthesis of Organic Semiconductor Nanoparticles with Different Conformations Using the Nanoprecipitation Method.

In recent years, nanoparticulate materials have aroused interest in the field of organic electronics due to their high versatility which increases the efficiency of devices. In this work, four different stable conformations based on the organic semiconductors P3HT and PC71BM were synthesized using the nanoprecipitation method, including blend and core-shell nanoparticles. All nanoparticles were obtained free of surfactants and in aqueous suspensions following the line of ecologically correct routes. The structural and optoelectronic properties of the nanoparticles were investigated by dynamic light scattering (DLS), transmission electron microscopy (TEM), scanning electron microscopy (SEM), UV-visible absorption spectroscopy and UV-visible photoluminescence (PL). Even in aqueous media, the blend and core-shell nanoparticles exhibited a greater light absorption capacity, and these conformations proved to be effective in the process of dissociation of excitons that occurs at the P3HT donor/PC71BM acceptor interface. With all these characteristics and allied to the fact that the nanoparticles are surfactant-free aqueous suspensions, this work paves the way for the use of these colloids as a photoactive layer of organic photovoltaic devices that interface with biological systems.

Defect activated optical Raman modes in single layer MoSe2.

In the last decade, transition metal dichalcogenides (TMDs) have been intensively synthesized/studied thus linking their morphological aspect to their physical properties, and consequently leading to the understanding of the possible benefits of defects in such materials. Nevertheless, for future applications, quantifying and identifying defects in TMDs is still a milestone to reach in order to better employ these materials in optoelectronic devices. Raman Spectroscopy has been successfully employed in graphene to quantify punctual or line defects. In this paper, we bombarded monolayer MoSe2with He ions and found out the existence of three defect activated Raman bands around 250-300 cm-1. Density functional theory calculations were employed to obtain the electronic and phonon dispersion bands, making it possible to infer that these bands arise from inter-valley Raman double resonance processes. Interestingly, the same punctual defect model, that allows one to predict the defect concentration at which graphene starts to become amorphous, also works for TMDs. Hence, this work opens the door to the macroscopic quantification of defects in TMDs, which is essential for technological applications.

Ecological Biosubstrates Obtained from Onion Pulp (Allium cepa L.) for Flexible Organic Light-Emitting Diodes.

A new biopolymer obtained from onion pulp (Allium cepa L.) was employed to produce a sustainable substrate for flexible organic light-emitting diodes (FOLEDs). Indium tin oxide (ITO) and SiO2 thin films were deposited by rf-magnetron sputtering onto these biosubstrates to obtain flexible, transparent, and conductive anodes, on top of which FOLEDs were produced. This new biomaterial exhibits an optical transparency of 63% at 550 nm. ITO films were optimized by varying rf power during deposition onto the biopolymers, and their electrical properties are comparable to the those of ITO grown on top of rigid substrates: a carrier concentration of -3.63 × 1021 cm-3 and carrier mobility of 7.72 cm2 V-1 s-1 for the optimized film. Consequently, the sheet resistance and resistivity of this ITO film were 8.92 Ω sq-1 and 2.23 × 10-4 Ω cm, respectively, hence allowing the production of FOLEDs. The A. cepa L. based FOLED was fabricated using CuPc, ß-NPB, and Alq3 as organic layers, and it exhibited a maximum luminance of about 2062 cd m-2 at 16.6 V. The current efficiency reached a maximum value of 2.1 cd A-1 at 85.3 mA cm-2. The obtained results suggest the possibility to use these substrates for innovative biocompatible applications in optoelectronics, such as photodynamic therapy.

Squaraine Dye for a Visibly Transparent All-Organic Optical Upconversion Device with Sensitivity at 1000 nm.

Efficient light detection in the near-infrared (NIR) wavelength region is central to emerging applications such as medical imaging and machine vision. An organic upconverter (OUC) consists of a NIR-sensitive organic photodetector (OPD) and an visible organic light-emitting diode (OLED), connected in series. The device converts NIR light directly to visible light, allowing imaging of a NIR scene in the visible. Here, we present an OUC composed of a NIR-selective squaraine dye-based OPD and a fluorescent OLED. The OPD has a peak sensitivity at 980 nm and an internal photon-to-current conversion efficiency of ∼100%. The OUC conversion efficiency (0.27%) of NIR to visible light is close to the expected maximum. The materials of the OUC multilayer stack absorb very little light in the visible wavelength range. In combination with an optimized semitransparent metal top electrode, this enabled the fabrication of transparent OUCs with an average visible transmittance of 65% and a peak transmittance of 80% at 620 nm. Visibly transparent OUCs are interesting for window-integrated electronic circuits or imaging systems that allow for the simultaneous detection of directly transmitted visible and NIR upconverted light.

Direct immobilization of avidin protein on AFM tip functionalized by acrylic acid vapor at RF plasma.

The atomic force microscopy (AFM) has been used as a force sensor to measure unbinding forces of single bound complexes in the nanonewton and piconewton range. Force spectroscopy measurements can be applied to study both intermolecular and intramolecular interactions of complex biological and synthetic macromolecules. Although the AFM has been extensively used as a nano force sensor, the commercially available cantilever is limited to silicon and silicon nitride. Those materials reduce the adhesion sensitivity with specific surface and/or molecule. Here, we functionalized the AFM tip with carboxylic groups by applying acrylic acid (AA) vapor at radio frequency plasma treatment at 100 W for 5 min. This method provides a remarkable sensitivity enhancement on the functional group interaction specificity. The functionalized tip was characterized by scanning electron microscopy. The electron beam high resolution images have not shown significant tip sharpness modification. Silicon wafers (1 0 0)-no treated and functionalized by AA plasma treatment-were characterized by Auger electron spectroscopy to elucidate the silicon surface sputtering and demonstrate functionalization. The Fourier transform-infrared spectroscopy spectrum shows a high absorbance of avidin protein over the silicon surface functionalized by AA plasma treatment.We carried out force spectroscopy assay to measure the unbinding force between the well-established pair biotin-avidin. At pulling speed of 2 µm/s, we measured the unbinding force of 106 ± 23 pN, which is in good agreement with the literature, demonstrating the effectiveness of the tip functionalization by AA plasma treatment in biological studies.