Iron Speciation in Respirable Particulate Matter and Implications for Human Health.

Particulate matter (PM) air pollution poses a major global health risk, but the role of iron (Fe) is not clearly defined because chemistry at the particle-cell interface is often not considered. Detailed spectromicroscopy characterizations of PM2.5 samples from the San Joaquin Valley, CA identified major Fe-bearing components and estimated their relative proportions. Iron in ambient PM2.5 was present in spatially and temporally variable mixtures, mostly as Fe(III) oxides and phyllosilicates, but with significant fractions of metallic iron (Fe(0)), Fe(II,III) oxide, and Fe(III) bonded to organic carbon. Fe(0) was present as aggregated, nm-sized particles that comprised up to ∼30% of the Fe spectral fraction. Mixtures reflect anthropogenic and geogenic particles subjected to environmental weathering, but reduced Fe in PM originates from anthropogenic sources, likely as abrasion products. Possible mechanistic pathways involving Fe(0) particles and mixtures of Fe(II) and Fe(III) surface species may generate hydrogen peroxide and oxygen-centered radical species (hydroxyl, hydroperoxyl, or superoxide) in Fenton-type reactions. From a health perspective, PM mixtures with reduced and oxidized Fe will have a disproportionate effect in cellular response after inhalation because of their tendency to shuttle electrons and produce oxidants and electrophiles that induce inflammation and oxidative stress.

Iron Speciation in Particulate Matter (PM2.5) from Urban Los Angeles Using Spectro-microscopy Methods.

The speciation, oxidation states, and relative abundance of iron (Fe) phases in PM2.5 samples from two locations in urban Los Angeles were investigated using a combination of bulk and spatially resolved, element-specific spectroscopy and microscopy methods. Synchrotron X-ray absorption spectroscopy (XAS) of bulk samples in situ (i.e., without extraction or digestion) was used to quantify the relative fractions of major Fe phases, which were corroborated by spatially resolved spectro-microscopy measurements. Ferrihydrite (amorphous Fe(III)-hydroxide) comprised the largest Fe fraction (34-52%), with hematite (α-Fe2O3; 13-23%) and magnetite (Fe3O4; 10-24%) identified as major crystalline oxide components. An Fe-bearing phyllosilicate fraction (16-23%) was fit best with a reference spectrum of a natural illite/smectite mineral, and metallic Fe(0) was a relatively small (2-6%) but easily identified component. Sizes, morphologies, oxidation state, and trace element compositions of Fe-bearing PM from electron microscopy, electron energy loss spectroscopy (EELS), and scanning transmission X-ray microscopy (STXM) revealed variable and heterogeneous mixtures of Fe species and phases, often associated with carbonaceous material with evidence of surface oxidation. Ferrihydrite (or related Fe(III) hydroxide phases) was ubiquitous in PM samples. It forms as an oxidation or surface alteration product of crystalline Fe phases, and also occurs as coatings or nanoparticles dispersed with other phases as a result of environmental dissolution and re-precipitation reactions. The prevalence of ferrihydrite (and adsorbed Fe(III) has likely been underestimated in studies of ambient PM because it is non-crystalline, non-magnetic, more soluble than crystalline phases, and found in complex mixtures. Review of potential sources of different particle types suggests that the majority of Fe-bearing PM from these urban sites originates from anthropogenic activities, primarily abrasion products from vehicle braking systems and engine emissions from combustion and/or wear. These variable mixtures have a high probability for electron transfer reactions between Fe, redox-active metals such as copper, and reactive carbon species such as quinones. Our findings suggest the need to assess biological responses of specific Fe-bearing phases both individually and in combination to unravel mechanisms of adverse health effects of particulate Fe.

Surface characterization and chemical speciation of adsorbed iron(iii) on oxidized carbon nanoparticles.

Carbonaceous nanomaterials represent a significant portion of ultra-fine airborne particulate matter, and iron is the most abundant transition metal in air particles. Owing to their high surface area and atmospheric oxidation, carbon nanoparticles (CNP) are enriched with surface carbonyl functional groups and act as a host for metals and small molecules. Using a synthetic model, concentration-dependent changes in the chemical speciation of iron adsorbed on oxidized carbon surfaces were investigated by a combination of X-ray and electron microscopic and spectroscopic methods. Carbon K-edge absorption spectra demonstrated that the CNP surface was enriched with carboxylic acid groups after chemical oxidation but that microporosity was unchanged. Oxidized CNP showed a high affinity for sorption of Fe(iii) from solution (75-95% uptake) and spectroscopic measurements confirmed a 3+ oxidation state of Fe on CNP irrespective of surface loading. The bonding of adsorbed Fe(iii) at variable loadings was determined by iron K-edge X-ray absorption spectroscopy. At low loadings (3 and 10 µmol Fe m-2 CNP), mononuclear Fe was octahedrally coordinated to oxygen atoms of carboxylate groups. As Fe surface coverage increased (21 and 31 µmol Fe m-2 CNP), Fe-Fe backscatters were observed at interatomic distances indicating iron (oxy)hydroxide particle formation on CNP. Electron-donating surface carboxylate groups on CNP coordinated and stabilized mononuclear Fe(iii). Saturation of high-affinity sites may have promoted hydroxide particle nucleation at higher loading, demonstrating that the chemical form of reactive metal ions may change with surface concentration and degree of CNP surface oxidation. Model systems such as those discussed here, with controlled surface properties and known chemical speciation of adsorbed metals, are needed to establish structure-activity models for toxicity assessments of environmentally relevant nanoparticles.

The bismuth oxyhalide family: thin film synthesis and periodic properties.

Bismuth oxyhalides (BiOX, where X = F, Cl, Br, I) are interesting materials due to their layered structure, which can be useful for different applications. In this work, we present the synthesis of the complete BiOX family in the thin film form. The tetragonal phase Bi2O3 film deposited onto a glass substrate was transformed into BiOF, BiOCl or BiOBr by a simple immersion at ambient temperature in a halide (X = F, Cl, Br) containing solution. For these films, a residual phase from the oxide was present and for BiOF another phase (tentatively identified as Bi7O5F11) was present too. For the BiOI film synthesis, an iodine and bismuth containing solution was sprayed onto the glass substrate heated at 275 °C and a pure phase was obtained. Microstructural and morphological characterization was performed by X-ray diffraction and scanning electron microscopy, while the chemical environment was studied by X-ray photoelectron spectroscopy. Optical and photocatalytic properties were also obtained. The physical and chemical characteristics of the BiOX films follow a correlation with the atomic radius of the halogen atom incorporated into the corresponding lattice. All the BiOX films showed a photocatalytic response for the photodiscoloration of indigo carmine dye under simulated sunlight irradiation in an alkaline medium. The photocatalytic reactions occurred via 2 proton-electron transfer from the oxide or oxyhalide to the adsorbed IC dye, favoring its reduction to the corresponding leuco IC form.

Endothelial cells derived from embryonic stem cells respond to cues from topographical surface patterns.

The generation of micro- and nano-topography similar to those found in the extra cellular matrix of three-dimensional tissues is one technique used to recapitulate the cell-tissue physiology found in the native tissues. Despite the fact that ample studies have been conducted on the physiological significance of endothelial cells alignment parallel to shear stress, as this is the normal physiologic arrangement for healthy arterial EC, very few studies have examined the use of topographical signals to initiate endothelial cell alignment. Here, we have examined the ability for our mouse embryonic stem cell-derived endothelial cells (ESC-EC) to align on various microchip topographical systems. Briefly, we generated metal molds with 'wrinkled' topography using 1) 15 nm and 2) 30 nm of gold coating on the pre-strained polystryene (PS) sheets. After thermal-induced shrinkage of the PS sheets, polydimethylsiloxane (PDMS) microchips were then generated from the wrinkled molds. Using similar Shrink™-based technology, 3) larger selectively crazed acetone-etched lines in the PS sheets, and 4) fully crazed acetone-treated PS sheets of stochastic topographical morphology were also generated. The 15 nm and 30 nm gold coating generated 'wrinkles' of uniaxial anisotropic channels at nano-scaled widths while the crazing generated micron-sized channels. The ESC-EC were able to respond and align on the 320 nm, 510 nm, and the acetone-etched 10.5 µm channels, but not on the fully 'crazed' topographies. Moreover, the ESC-EC aligned most robustly on the wrinkles, and preferentially to ridge edges on the 10.5 µm-sized channels. The ability to robustly align EC on topographical surfaces enables a variety of controlled physiological studies of EC-EC and EC-ECM contact guidance, as well as having potential applications for the rapid endothelialization of stents and vascular grafts.

Spatially resolved energy electron loss spectroscopy studies of iron oxide nanoparticles.

The oxidation state of iron oxide nanoparticles co-generated with soot during a combustion process was studied using electron energy-loss spectroscopy (EELS). Spatially resolved EELS spectra in the scanning transmission electron microscopy mode were collected to detect changes in the oxidation state between the cores and surfaces of the particles. Quantification of the intensity ratio of the white lines of the iron L-ionization edge was used to measure the iron oxidation state. Quantitative results obtained from Pearson's method, which can be directly compared with the literature data, indicated that the L3 /L2-intensity ratio for these particles changes from 5.5 +/- 0.3 in the particles' cores to 4.4 +/- 0.3 at their surfaces. This change can be directly related to the reduction of the iron oxidation state at the surface of the particles. Experimental results indicate that the cores of the particles are composed of gamma-Fe2O3, which seems to be reduced to FeO at their surfaces. These results were also supported by the fine structure of the oxygen K-edge and by the significant chemical shift of the iron L-edge.

Reduced lung cell proliferation following short-term exposure to ultrafine soot and iron particles in neonatal rats: key to impaired lung growth?

Particulate matter (PM) has been associated with a variety of negative health outcomes in children involving the respiratory system and early development. However, the precise mechanisms to explain how exposure to airborne particles may cause adverse effects in children are unknown. To study their influence on early postnatal development, a simple, laminar diffusion flame was used to generate an aerosol of soot and iron particles in the size range of 10 to 50 nm. Exposure of 10-day-old rat pups to soot and iron particles was for 6 h/day for 3 days. The lungs were examined following a single injection of bromodeoxyuridine (BrdU) 2 h prior to necropsy. Neonatal rats exposed to these particles demonstrated no effect on the rate of cell proliferation within terminal bronchioles or the general lung parenchyma. In contrast, within those regions arising immediately beyond the terminal bronchioles (defined as the proximal alveolar region), the rate of cell proliferation was significantly reduced compared with filtered air controls. These findings strongly suggest exposure to airborne particles during early neonatal life has significant direct effects on lung growth by altering cell division within critical sites of the respiratory tract during periods of rapid postnatal development. Such effects may result in altered growth in the respiratory system that may be associated with lifelong consequences.

Oxidative stress and NFkappaB activation in the lungs of rats: a synergistic interaction between soot and iron particles.

Particulate matter (PM) has been associated with a variety of adverse health effects primarily involving the cardiopulmonary system. However, the precise biological mechanisms to explain how exposure to PM exacerbates or directly causes adverse effects are unknown. Particles of varying composition may play a critical role in these effects. To study such a phenomenon, a simple, laminar diffusion flame was used to generate aerosols of soot and iron particles in the ultrafine size range. Exposures of healthy adult rats were for 6 h/day for 3 days. Conditions used included exposure to soot only, iron only, or a combination of soot and iron. We found animals exposed to soot particles at 250 microg/m3 had no adverse respiratory effects. Exposure to iron alone at a concentration of 57 microg/m3 also had no respiratory effects. However, the addition of 45 microg/m3 of iron to soot with a combined total mass concentration of 250 microg/m3 demonstrated significant pulmonary ferritin induction, oxidative stress, elevation of IL-1beta, and cytochrome P450s, as well as activation of NFkappaB. These findings suggest that a synergistic interaction between soot and iron particles account for biological responses not found with exposure to iron alone or to soot alone.