Sn-Cu nanocomposite anodes for rechargeable sodium-ion batteries.

Sn0.9Cu0.1 nanoparticles were synthesized via a surfactant-assisted wet chemistry method, which were then investigated as an anode material for ambient temperature rechargeable sodium ion batteries. The Sn0.9Cu0.1 nanoparticle-based electrodes exhibited a stable capacity of greater than 420 mA h g(-1) at 0.2 C rate, retaining 97% of their maximum observed capacity after 100 cycles of sodium insertion/deinsertion. Their performance is considerably superior to electrodes made with either Sn nanoparticles or Sn microparticles.

Nanostructured Si(1-x)Gex for tunable thin film lithium-ion battery anodes.

Both silicon and germanium are leading candidates to replace the carbon anode of lithium ions batteries. Silicon is attractive because of its high lithium storage capacity while germanium, a superior electronic and ionic conductor, can support much higher charge/discharge rates. Here we investigate the electronic, electrochemical and optical properties of Si(1-x)Gex thin films with x = 0, 0.25, 0.5, 0.75, and 1. Glancing angle deposition provided amorphous films of reproducible nanostructure and porosity. The film's composition and physical properties were investigated by X-ray photoelectron spectroscopy, four-point probe conductivity, Raman, and UV-vis absorption spectroscopy. The films were assembled into coin cells to test their electrochemical properties as a lithium-ion battery anode material. The cells were cycled at various C-rates to determine the upper limits for high rate performance. Adjusting the composition in the Si(1-x)Gex system demonstrates a trade-off between rate capability and specific capacity. We show that high-capacity silicon anodes and high-rate germanium anodes are merely the two extremes; the composition of Si(1-x)Gex alloys provides a new parameter to use in electrode optimization.

Storage of Lithium in Hydrothermally Synthesized GeO2 Nanoparticles.

Amorphous GeO2 nanoparticles were prepared via a surfactant-assisted hydrothermal process. The effect of the reaction temperature and the surfactant concentration on the morphology of GeO2 particles were investigated. Particles of less than 300 nm were obtained when using 1,2-diaminopropane surfactant in a synthesis carried out at 180(◦)C. The synthesized germanium oxide nanoparticles were evaluated for their utility as the active anode material in Li-ion batteries. The electrode prepared with this material exhibited a stable capacity ∼600 mAh g(-1) at 0.2 C rate for up to 150 cycles in a conventional electrolyte containing ethylene carbonate (EC). The cyclability of the GeO2 nanoparticle electrode was further improved by using a fluorinated ethylene carbonate (FEC) based electrolyte, which showed capacities greater than 600 mAh g(-1) and retained more than 96% of their capacity after 500 cycles at 0.2 C rate. The effect of different electrolyte systems was studied by using electrochemical impedance spectroscopy and electron microscopy.

High performance silicon nanoparticle anode in fluoroethylene carbonate-based electrolyte for Li-ion batteries.

Electrodes composed of silicon nanoparticles (SiNP) were prepared by slurry casting and then electrochemically tested in a fluoroethylene carbonate (FEC)-based electrolyte. The capacity retention after cycling was significantly improved compared to electrodes cycled in a traditional ethylene carbonate (EC)-based electrolyte.

Improving the stability of nanostructured silicon thin film lithium-ion battery anodes through their controlled oxidation.

Silicon and partially oxidized silicon thin films with nanocolumnar morphology were synthesized by evaporative deposition at a glancing angle, and their performance as lithium-ion battery anodes was evaluated. The incorporated oxygen concentration was controlled by varying the partial pressure of water during the deposition and monitored by quartz crystal microbalance, X-ray photoelectron spectroscopy. In addition to bulk oxygen content, surface oxidation and annealing at low temperature affected the cycling stability and lithium-storage capacity of the films. By simultaneously optimizing all three, films of ~2200 mAh/g capacity were synthesized. Coin cells made with the optimized films were reversibly cycled for ~120 cycles with virtually no capacity fade. After 300 cycles, 80% of the initial reversible capacity was retained.

Reactive ballistic deposition of nanostructured model materials for electrochemical energy conversion and storage.

Porous, high surface area materials have critical roles in applications including catalysis, photochemistry, and energy storage. In these fields, researchers have demonstrated that the nanometer-scale structure modifies mechanical, optical, and electrical properties of the material, greatly influencing its behavior and performance. Such complex chemical systems can involve several distinct processes occurring in series or parallel. Understanding the influence of size and structure on the properties of these materials requires techniques for producing clean, simple model systems. In the fields of photoelectrochemistry and lithium storage, for example, researchers need to evaluate the effects of changing the electrode structure of a single material or producing electrodes of many different candidate materials while maintaining a distinctly favorable morphology. In this Account, we introduce our studies of the formation and characterization of high surface area, porous thin films synthesized by a process called reactive ballistic deposition (RBD). RBD is a simple method that provides control of the morphology, porosity, and surface area of thin films by manipulating the angle at which a metal-vapor flux impinges on the substrate during deposition. This approach is largely independent of the identity of the deposited material and relies upon limited surface diffusion during synthesis, which enables the formation of kinetically trapped structures. Here, we review our results for the deposition of films from a number of semiconductive materials that are important for applications such as photoelectrochemical water oxidation and lithium ion storage. The use of RBD has enabled us to systematically control individual aspects of both the structure and composition of thin film electrodes in order to probe the effects of each on the performance of the material. We have evaluated the performance of several materials for potential use in these applications and have identified processes that limit their performance. Use of model systems, such as these, for fundamental studies or materials screening processes likely will prove useful in developing new high-performance electrodes.