Interlocking-interface-enabled thermally deformable liquid metal/polymer membrane with high bonding strength.

HYPOTHESIS: The high surface tension of liquid metal (LM) causes interface incompatibility and poor bonding strength with many substrates. Fine adjustment towards the properties of the surface area is sufficient to introduce strong bonding. Hence, we hypothesize that the interlocking structure using hydrophilic polyvinyl alcohol (PVA) as a "bridge" should be helpful for tight interfacial bonding of LM with polymeric substrates, thus achieving high-performance LM/polymer membranes, which have wide applications in the field of soft sensors and robotics. EXPERIMENTS: The bulk EGaIn was fabricated into LM nanoparticles (LMNPs@PVA) solution. Then, PVA molecules were "doped" into the surface crosslink of the plasma treated polymer substrate by an interfacial penetrating method. Afterward, the solution was evenly dropped on the surface of the treated substrate to obtain the LMNP/polymer membrane after the water evaporated. Photothermal actuators were fabricated based on the membranes. FINDINGS: During the interlocking structure, PVA macromolecules could be doped and trapped onto the top surfaces of various polymer substrates as binding "bridges" between the LMNPs and the matrix materials. The achieved LMNP membrane exhibites satisfactory bonding strength, durability and water-assisted erase-reprint, which can be used as soft photothermal actuators with remote laser control.

A U-Shaped Dual-Frequency-Reconfigurable Monopole Antenna Based on Liquid Metal.

This study presents a U-shaped dual-frequency-reconfigurable liquid-metal monopole antenna. Eutectic Gallium-Indium (EGaIn) was used as a conductive fluid and filled in the two branches of the U-shaped glass tube. A precision syringe pump was connected to one of the branches of the U-shaped tube by a silicone tube to drive EGaIn, forming a height difference between the two liquid levels. When the height of liquid metal in the two branches met the initial condition of L1 = L2 = 10 mm, and L1 increased from 10 mm to 18 mm, the two branches obtained two working bandwidths of 2.27-4.98 GHz and 2.71-8.58 GHz, respectively. The maximum peak gain was 4.00 dBi. The initial amount of EGaIn also affected the available operating bandwidth. When the liquid metal was perfused according to the initial condition: L1 = L2 = 12 mm, and L1 was adjusted within the range of 12-20 mm, the two branches had the corresponding working bandwidths of 2.18-4.32 GHz and 2.57-9.09 GHz, and the measured maximum peak gain was 3.72 dBi. The simulation and measurement data corresponded well. A series of dual-frequency-reconfigurable antennas can be obtained by changing the initial amount of EGaIn. This series of antennas may have broad application prospects in fields such as base stations and navigation.

A Gravity-Triggered Liquid Metal Patch Antenna with Reconfigurable Frequency.

In this paper, a gravity-triggered liquid metal microstrip patch antenna with reconfigurable frequency is proposed with experimental verification. In this work, the substrate of the antenna is quickly obtained through three-dimensional (3D) printing technology. Non-toxic EGaIn alloy is filled into the resin substrate as a radiation patch, and the NaOH solution is used to remove the oxide film of EGaIn. In this configuration, the liquid metal inside the antenna can be flexibly flowed and deformed with different rotation angles due to the gravity to realize different working states. To validate the conception, the reflection coefficients and radiation patterns of the prototyped antenna are then measured, from which it can be observed that the measured results closely follow the simulations. The antenna can obtain a wide operating bandwidth of 3.69-4.95 GHz, which coverage over a range of frequencies suitable for various channels of the 5th generation (5G) mobile networks. The principle of gravitational driving can be applied to the design of reconfigurable antennas for other types of liquid metals.

The Design and Manufacturing Process of an Electrolyte-Free Liquid Metal Frequency-Reconfigurable Antenna.

This communication provides an integrated process route of smelting gallium-based liquid metal (GBLM) in a high vacuum, and injecting GBLM into the antenna channel in high-pressure protective gas, which avoids the oxidation of GBLM during smelting and filling. Then, a frequency-reconfigurable antenna, utilizing the thermal expansion characteristic of GBLM, is proposed. To drive GBLM into an air-proof space, the thermal expansion characteristics of GBLM are required. The dimensions of the radiating element of the liquid metal antenna can be adjusted at different temperatures, resulting in the reconfigurability of the operating frequency. To validate the proposed concept, an L-band antenna prototype was fabricated and measured. Experimental results demonstrate that the GBLM in the antenna was well filled, and the GBLM was not oxidized. Due to the GBLM being in an air-proof channel, the designed liquid metal antenna without electrolytes could be used in an air environment for a long time. The antenna is able to achieve an effective bandwidth of over 1.25-2.00 GHz between 25 °C and 100 °C. The maximum radiation efficiency and gain in the tunable range are 94% and 2.9 dBi, respectively. The designed antenna also provides a new approach to the fabrication of a temperature sensor that detects temperature in some situations that are challenging for conventional temperature sensing technology.

Microwave-assisted synthesis of BSA-protected small gold nanoclusters and their fluorescence-enhanced sensing of silver(I) ions.

A one-step microwave-assisted method is used for the synthesis of small gold nanoclusters, Au(16)NCs@BSA, which are used as a fluorescence enhanced sensor for detection of silver(I) ions with high selectivity and sensitivity.