RESUMEN
Silicon photonic sensors based on Mach Zehnder Interferometers (MZIs) have applications spanning from biological and olfactory sensors to temperature and ultrasound sensors. Although a coherent detection scheme can solve the issues of sensitivity fading and ambiguity in phase direction, the measured phase remains 2π periodic. This implies that the acquisition frequency should ensure a phase shift lower than π between each measurement point to prevent 2π phase jumps. Here, we describe and experimentally characterize two methods based on reference MZIs with lower sensitivities to alleviate this drawback. These solutions improve the measurement robustness and allow the lowering of the acquisition frequency. The first method is based on the phase derivative sign comparison. When a discrepancy is detected, the reference MZI is used to choose whether 2π should be added or removed from the nominal MZI. It can correct 2π phase jumps regardless of the sensitivity ratio, so that a single reference MZI can be used to correct multiple nominal MZIs. This first method relaxes the acquisition frequency requirement by a factor of almost two. However, it cannot correct phase jumps of 4π, 6π or higher between two measurement points. The second method is based on the comparison between the measured phase from the nominal MZI and the phase expected from the reference MZI. It can correct multiple 2π phase jumps but requires at least one reference MZI per biofunctionalization. It will also constrain the corrected phase to lie in a limited interval of [-π, +π] around the expected value, and might fail to correct phase shifts above a few tens of radians depending on the disparity of the nominal sensors responses. Nonetheless, for phase shift lower than typically 20 radians, this method allows the lowering of the acquisition frequency almost arbitrarily.
RESUMEN
Silicon photonics can address a variety of applications, from datacom and biosensing to lidars. Recently, this technology has been explored for gas sensing. Detection and identification of odors remains a critical challenge in diverse areas such as air quality, food spoilage, or personal well-being. In this work, we present an olfactory sensor based on an array of 64 biofunctionalized Mach-Zehnder interferometers integrated on a silicon nitride platform. The ability to analyze odors at ppm level is demonstrated for several volatile organic compounds.
Asunto(s)
Técnicas Biosensibles , Compuestos Orgánicos Volátiles , Interferometría , Óptica y Fotónica , FotonesRESUMEN
An electronic nose (e-nose) utilizes a multisensor array, which relies on the vector contrast of combinatorial responses, to effectively discriminate between volatile organic compounds (VOCs). In recent years, hierarchical structures made of nonbiological materials have been used to achieve the required sensor diversity. With the advent of self-assembling peptides, the ability to tune nanostructuration, surprisingly, has not been exploited for sensor array diversification. In this work, a designer surfactant-like peptide sequence, CG7-NH2, is used to fabricate morphologically and physicochemically heterogeneous "biohybrid" surfaces on Au-covered chips. These multistructural sensing surfaces, containing immobilized hierarchical nanostructures surrounded by self-assembled monolayers, are used for the detection and discrimination of VOCs. Through a simple and judicious design process, involving changes in pH and water content of peptide solutions, a five-element biohybrid sensor array coupled with a gas-phase surface plasmon resonance imaging system is shown to achieve sufficient discriminatory capabilities for four VOCs. Moreover, the limit of detection of the multiarray system is bench-marked at <1 and 6 ppbv for hexanoic acid and phenol (esophago-gastric biomarkers), respectively. Finally, the humidity effects are characterized, identifying the dissociation rate constant as a robust descriptor for classification, further exemplifying their efficacy as biomaterials in the field of artificial olfaction.
Asunto(s)
Nanoestructuras , Surfactantes Pulmonares , Compuestos Orgánicos Volátiles , Nariz Electrónica , Péptidos , TensoactivosRESUMEN
Differential sensing of proteins based on cross-reactive arrays and pattern recognition is a promising technique for the detection and identification of proteins. In this study, a rational biomimetic strategy has been used to prepare sensing materials capable of discriminating structurally similar proteins, such as deletion and point mutants of a cytokine, by mimicking the biological properties of heparan sulfate (HS). Using the self-assembly of two disaccharides, lactose and sulfated lactose at various ratios on the surface of a chip, an array of combinatorial cross-reactive receptors has been prepared. Coupling with surface plasmon resonance imaging (SPRi), the obtained cross-reactive array is very efficient for protein sensing. It is able to detect HS binding proteins (HSbps) such as IFNγ at nanomolar concentrations. Moreover, such a system is capable of discriminating between IFNγ and its mutants with good selectivity.
Asunto(s)
Citocinas , Heparitina Sulfato , Biomimética , Disacáridos , Heparitina Sulfato/química , Resonancia por Plasmón de Superficie/métodosRESUMEN
Improving the sensitivity of plasmonic optical fiber sensors constitutes a major challenge as it could significantly enhance their sensing capabilities for the label-free detection of biomolecular interactions or chemical compounds. While many efforts focus on developing more sensitive structures, we present here how the sensitivity of a sensor can be significantly enhanced by improving the light analysis. Contrary to the common approach where the global intensity of the light coming from the core is averaged, our approach is based on the full analysis of the retro-reflected intensity distribution that evolves with the refractive index of the medium being analyzed. Thanks to this original and simple approach, the refractive index sensitivity of a plasmonic optical fiber sensor used in reflection mode was enhanced by a factor of 25 compared to the standard method. The reported approach opens exciting perspectives for improving the remote detection as well as for developing new sensing strategies.
RESUMEN
Chiral discrimination is a key problem in analytical chemistry. It is generally performed using expensive instruments or highly-specific miniaturized sensors. An electronic nose is a bio-inspired instrument capable after training of discriminating a wide variety of analytes. However, generality is achieved at the cost of specificity which makes chiral recognition a challenging task for this kind of device. Recently, a peptide-based optoelectronic nose which can board up to hundreds of different sensing materials has shown promising results, especially in terms of specificity. In line with these results, we describe here its use for chiral recognition. This challenging task requires care, especially in terms of statistical reliability and experimental confounds. For these reasons, we set up an automatic gas sampling system and recorded data over two long sessions, taking care to exclude possible confounds. Two couples of chiral molecules, namely (R) and (S) Limonene and (R) and (S) Carvone, were tested and several statistical analyses indicate the almost perfect discrimination of their two enantiomers. A method to highlight discriminative sensing materials is also proposed and shows that successful discrimination is likely achieved using just a few peptides.
Asunto(s)
Técnicas Biosensibles , Nariz Electrónica , Algoritmos , Modelos Químicos , Péptidos/análisis , Reproducibilidad de los ResultadosRESUMEN
The analysis of volatile organic compounds (VOCs) is an important issue in various domains. For this, electronic noses (eN) are very promising as novel analytical tools that are portable, inexpensive, and efficient for reliable and rapid analyses. Recently, we have demonstrated that surface plasmon resonance imaging (SPRI) is especially interesting for the development of eNs dedicated for gas-phase analysis of VOCs. To further improve the performance of the eN based on SPRI, in this study, we investigated the influence of the LED wavelength on the sensitivity of the system. For this, a complete theoretical study together with a related experimental investigation for the validation were carried out. We have shown that the wavelength of the light source has an impact on the surface sensitivity of SPRI for the detection of VOCs. Indeed, in the studied wavelength range from 530 nm to 740 nm, both bulk sensitivity and surface sensitivity increase as the wavelength increases with good coherence between theoretical and experimental results. With the optimal LED wavelength, the detection limits of our eN reach low ppb range for VOC such as 1-butanol.
RESUMEN
This review summarizes recent advances in micro- and nanopore technologies with a focus on the functionalization of pores using a promising method named contactless electro-functionalization (CLEF). CLEF enables the localized grafting of electroactive entities onto the inner wall of a micro- or nano-sized pore in a solid-state silicon/silicon oxide membrane. A voltage or electrical current applied across the pore induces the surface functionalization by electroactive entities exclusively on the inside pore wall, which is a significant improvement over existing methods. CLEF's mechanism is based on the polarization of a sandwich-like silicon/silicon oxide membrane, creating electronic pathways between the core silicon and the electrolyte. Correlation between numerical simulations and experiments have validated this hypothesis. CLEF-induced micro- and nanopores functionalized with antibodies or oligonucleotides were successfully used for the detection and identification of cells and are promising sensitive biosensors. This technology could soon be successfully applied to planar configurations of pores, such as restrictions in microfluidic channels.
Asunto(s)
Técnicas Biosensibles , Silicio/química , Impedancia Eléctrica , Técnicas Electroquímicas , Membranas Artificiales , NanoporosRESUMEN
Bipolar electrochemistry (BPE) is a powerful method based on the wireless polarization of a conductive object that induces the asymmetric electroactivity at its two extremities. A key physical limitation of BPE is the size of the conductive object because the shorter the object, the larger is the potential necessary for sufficient polarization. Micrometric and nanometric objects are thus extremely difficult to address by BPE due to the very high potentials required, in the order of tens of kV or more. Herein, the synergetic actions of BPE and of planar micropores integrated in a microfluidic device lead to the spatial confinement of the potential drop at the level of the solid-state micropore, and thus to a locally enhanced polarization of a bipolar electrode. Electrochemiluminescence (ECL) is emitted in half of the electroactive micropore and reveals the asymmetric polarization in this spatial restriction. Micrometric deoxidized silicon electrodes located in the micropore are polarized at a very low potential (7 V), which is more than 2 orders of magnitude lower compared to the classic bipolar configurations. This behavior is intrinsically associated with the unique properties of the micropores, where the sharp potential drop is focused. The presented approach offers exciting perspectives for BPE of micro/nano-objects, such as dynamic BPE with objects passing through the pores or wireless ECL-emitting micropores.
RESUMEN
Remote detection by surface plasmon resonance (SPR) is demonstrated through microstructured optical arrays of conical nanotips or micropillars. Both geometries were fabricated by controlled wet chemical etching of bundles comprising several thousands of individual optical fibers. Their surface was coated by a thin gold layer in order to confer SPR properties. The sensitivity and resolution of both shapes were evaluated as a function of global optical index changes in remote detection mode performed by imaging through the etched optical fiber bundle itself. With optimized geometry of micropillar arrays, resolution was increased up to 10-4 refractive index units. The gold-coated micropillar arrays were functionalized with DNA and were able to monitor remotely the kinetics of DNA hybridization with complementary strands. We demonstrate for the first time highly parallel remote SPR detection of DNA via microstructured optical arrays. The obtained SPR sensitivity combined with the remote intrinsic properties of the optical fiber bundles should find promising applications in biosensing, remote SPR imaging, a lab-on-fiber platform dedicated to biomolecular analysis, and in vivo endoscopic diagnosis. Graphical abstract We present a single fabrication step to structure simultaneously all the individual cores of an optical fiber bundle composed of thousands of fibers. The resulting sensor is optimized for reflection mode (compatible with in vivo applications) and is used to perform for the first time highly parallel remote SPR detection of DNA via several thousands of individual optical fiber SPR sensors paving the way for multiplexed biological detection.
Asunto(s)
ADN/análisis , Hibridación de Ácido Nucleico , Fibras Ópticas , Resonancia por Plasmón de Superficie/instrumentación , Diseño de Equipo , Tecnología de Fibra Óptica/instrumentación , Oro/química , Ácidos Nucleicos Inmovilizados/química , RefractometríaRESUMEN
Foodborne pathogens are of significant concern in the agrifood industry and the development of associated rapid detection and identification methods are of major importance. This paper describes the novel use of resolution-optimized prism-based surface plasmon resonance imaging (RO-SPRI) and data processing for the detection of the foodborne pathogens Listeria monocytogenes and Listeria innocua. With an imaging spatial resolution on the order of individual bacteria (2.7 ± 0.5 µm × 7.9 ± 0.6 µm) over a field of view 1.5 mm2, the RO-SPRI system enabled accurate counting of individual bacteria on the sensor surface. Using this system, we demonstrate the detection of two species of Listeria at an initial concentration of 2 × 102 CFU mL-1 in less than 7 hours. The surface density of bacteria at the point of positive detection was 15 ± 4 bacteria per mm2. Our approach offers great potential for the development of fast specific detection systems based on affinity monitoring.
RESUMEN
Monitoring volatile organic compounds (VOCs) is an important issue, but difficult to achieve on a large scale and on the field using conventional analytical methods. Electronic noses (eNs), as promising alternatives, are still compromised by their performances due to the fact that most of them rely on a very limited number of sensors and use databases devoid of kinetic information. To narrow the performance gap between human and electronic noses, we developed a novel optoelectronic nose, which features a large sensor microarray that enables multiplexed monitoring of binding events in real-time with a temporal response. For the first time, surface plasmon resonance imaging is demonstrated as a promising novel analytical tool for VOC detection in the gas phase. By combining it with cross-reactive sensor microarrays, the obtained optoelectronic nose shows a remarkably high selectivity, capable of discriminating between homologous VOCs differing by only a single carbon atom. In addition, the optoelectronic nose has good repeatability and stability. Finally, the preliminary assays using VOC binary and ternary mixtures show that it is also very efficient for the analysis of more complex samples, opening up the exciting perspective of applying it to "real-world" samples in diverse domains.
RESUMEN
Nowadays, there is a strong demand for the development of new analytical devices with novel performances to improve the quality of our daily lives. In this context, multisensor systems such as electronic tongues (eTs) have emerged as promising alternatives. Recently, we have developed a new versatile eT system by coupling surface plasmon resonance imaging (SPRi) with cross-reactive sensor arrays. In order to largely simplify the preparation of sensing materials with a great diversity, an innovative combinatorial approach was proposed by combining and mixing a small number of easily accessible molecules displaying different physicochemical properties. The obtained eT was able to generate 2D continuous evolution profile (CEP) and 3D continuous evolution landscape (CEL), which is also called 3D image, with valuable kinetic information, for the discrimination and classification of samples. Here, diverse applications of such a versatile eT have been summarized. It is not only effective for pure protein analysis, capable of differentiating protein isoforms such as chemokines CXCL12α and CXCL12γ, but can also be generalized for the analysis of complex mixtures, such as milk samples, with promising potential for monitoring the deterioration of milk.
Asunto(s)
Nariz Electrónica , Animales , Técnicas Biosensibles , Mezclas Complejas , Reacciones Cruzadas , Leche , Resonancia por Plasmón de SuperficieRESUMEN
A new kind of nanodevice that acts like tweezers through remote actuation by an external magnetic field is designed. Such device is meant to mechanically grab micrometric objects. The nanotweezers are built by using a top-down approach and are made of two parallelepipedic microelements, at least one of them being magnetic, bound by a flexible nanohinge. The presence of an external magnetic field induces a torque on the magnetic elements that competes with the elastic torque provided by the nanohinge. A model is established in order to evaluate the values of the balanced torques as a function of the tweezers opening angles. The results of the calculations are confronted to the expected values and validate the overall working principle of the magnetic nanotweezers.
RESUMEN
The identification and characterization, at the cellular level, of cytokine productions present a high interest for both fundamental research and clinical studies. However, the majority of techniques currently available (ELISA, ELISpot, flow cytometry, etc.) have several shortcomings including, notably, the assessment of several cytokines in relation to individual secreting cells and the monitoring of living cell responses for a long incubation time. In the present work, we describe a system composed of a microfluidic platform coupled with an antibody microarray chip for continuous SPR imaging and immunofluorescence analysis of cytokines (IL-2 and IFN-γ) secreted by T-Lymphocytes, specifically, and stably captured on the biochip under flow upon continued long-term on-chip culture (more than 24 h).
Asunto(s)
Anticuerpos Inmovilizados/química , Interferón gamma/análisis , Interleucina-2/análisis , Dispositivos Laboratorio en un Chip , Resonancia por Plasmón de Superficie/instrumentación , Linfocitos T/inmunología , Adulto , Anticuerpos Inmovilizados/inmunología , Supervivencia Celular , Diseño de Equipo , Humanos , Interferón gamma/inmunología , Interleucina-2/inmunología , Análisis por Matrices de Proteínas/instrumentación , Linfocitos T/químicaRESUMEN
Cancer cells develop resistance to chemotherapy, and the side effects encountered seriously limit the effectiveness of treatments. For these reasons, the search for alternative therapies that target cancer cells without affecting healthy tissues is currently one of the most active areas of research on cancer. The present study focuses on a recently proposed approach for cancer cell destruction based on the targeted triggering of cancer cell spontaneous death through the mechanical vibration of anisotropic magnetic micro/nanoparticles attached to the cell membranes at low frequencies (â¼20 Hz) and in weak magnetic fields (â¼30 mT). The study was conducted in vitro, on human renal cancer cells with superparamagnetic-like particles. Three types of such particles made of NiFe or magnetite were prepared and characterized (either synthetic antiferromagnetic, vortex or polycrystalline with random grain anisotropy). The triggering of the apoptosis of these cancer cells was demonstrated with NiFe vortex particles and statistically characterized by flow-cytometry studies. The death pathway via apoptosis and not necrosis was identified by the clear observation of caspase activation.
Asunto(s)
Apoptosis/efectos de los fármacos , Membrana Celular/efectos de los fármacos , Supervivencia Celular/efectos de los fármacos , Neoplasias Renales/metabolismo , Línea Celular Tumoral , Humanos , VibraciónRESUMEN
Microarrays are particular biosensors with multiple grafted probes that are generally used for parallel and simultaneous detection of various targets. In this study, we used microarrays with aptamer probes in order to follow up the different biomolecular interactions of a single enzyme, the thrombin protein, involved in the complex coagulation cascade. More precisely, thanks to label-free surface plasmon resonance imaging, we were able to monitor in real time an important step in the firing of the coagulation cascade in situ-the enzymatic transformation of prothrombin into thrombin, catalyzed by factor Xa. We were also able to appraise the influence of other biochemical factors and their corresponding inhibiting or enhancing behaviors on thrombin activation. Our study opens the door for the development of a complete microarray-based platform not only for the whole coagulation cascade analysis but also for novel drug screening assays in pharmacology.
Asunto(s)
Aptámeros de Nucleótidos/metabolismo , Técnicas Biosensibles/métodos , Análisis por Micromatrices/métodos , Protrombina/metabolismo , Trombina/metabolismo , Evaluación Preclínica de Medicamentos , Humanos , Trombina/antagonistas & inhibidoresRESUMEN
Prevention of foodborne diseases depends highly on our ability to control rapidly and accurately a possible contamination of food. So far, standard procedures for bacterial detection require time-consuming bacterial cultures on plates before the pathogens can be detected and identified. We present here an innovative biochip, based on direct differential carbohydrate recognitions of five closely related Escherichia coli strains, including the enterohemorragic E. coli O157:H7. Our device relies on efficient grafting of simple carbohydrates on a gold surface and on the monitoring of their interactions with bacteria during their culture using surface plasmon resonance imaging. We show that each of the bacteria interacts in a different way with the carbohydrate chip. This allows the detection and discrimination of the tested bacterial strains in less than 10 h from an initial bacterial concentration of 10(2) CFU·mL(-1). This is an improvement over previously described systems in terms of cost, easiness to use, and stability. Easily conceived and easily regenerated, this tool is promising for the future of food safety.
Asunto(s)
Metabolismo de los Hidratos de Carbono , Infecciones por Escherichia coli/microbiología , Escherichia coli/aislamiento & purificación , Análisis por Micromatrices/instrumentación , Sondas Moleculares/metabolismo , Resonancia por Plasmón de Superficie/instrumentación , Recuento de Colonia Microbiana , Diseño de Equipo , Escherichia coli/clasificación , Escherichia coli/metabolismo , Infecciones por Escherichia coli/diagnóstico , Escherichia coli O157/clasificación , Escherichia coli O157/aislamiento & purificación , Escherichia coli O157/metabolismo , Contaminación de Alimentos/análisis , Microbiología de Alimentos , Inocuidad de los Alimentos , Enfermedades Transmitidas por los Alimentos/diagnóstico , Enfermedades Transmitidas por los Alimentos/microbiología , Humanos , Análisis de Matrices Tisulares/instrumentaciónRESUMEN
Several optical surface sensing techniques, such as Surface Plasmon Resonance (SPR), work by imaging the base of a prism by one of its faces. However, such a fundamental optical concern has not been fully analyzed and understood so far, and spatial resolution remains a critical and controversial issue. In SPR, the propagation length L(x) of the surface plasmon waves has been considered as the limiting factor. Here, we demonstrate that for unoptimized systems geometrical aberrations caused by the prism can be more limiting than the propagation length. By combining line-scan imaging mode with optimized prisms, we access the ultimate lateral resolution which is diffraction-limited by the object light diffusion. We describe several optimized configurations in water and discuss the trade-off between L(x) and sensitivity. The improvement of resolution is confirmed by imaging micro-structured PDMS stamps and individual living eukaryote cells and bacteria on field-of-view from 0.1 to 20 mm(2).
Asunto(s)
Microscopía/instrumentación , Resonancia por Plasmón de Superficie/instrumentación , Diseño de EquipoRESUMEN
In current protocol, a combinatorial approach has been developed to simplify the design and production of sensing materials for the construction of electronic tongues (eT) for protein analysis. By mixing a small number of simple and easily accessible molecules with different physicochemical properties, used as building blocks (BBs), in varying and controlled proportions and allowing the mixtures to self-assemble on the gold surface of a prism, an array of combinatorial surfaces featuring appropriate properties for protein sensing was created. In this way, a great number of cross-reactive receptors can be rapidly and efficiently obtained. By combining such an array of combinatorial cross-reactive receptors (CoCRRs) with an optical detection system such as surface plasmon resonance imaging (SPRi), the obtained eT can monitor the binding events in real-time and generate continuous recognition patterns including 2D continuous evolution profile (CEP) and 3D continuous evolution landscape (CEL) for samples in liquid. Such an eT system is efficient for discrimination of common purified proteins.