Stainless Steel in Municipal Sewage-How to Recognize Favorable Corrosion Conditions.

While chromium-nickel steel is known to be extremely resistant to corrosion, the occurrence of certain factors can unfortunately initiate an uncontrolled corrosion process. This paper presents samples made of 304 stainless steel containing delta ferrite that have been exposed to wastewater for 18 months. Samples placed above the surface of the wastewater (A-series) were intensively corroded. Samples half-submerged in the wastewater and periodically fully submerged at higher effluent flows through the screenings and grit separator (B-series) only suffered minor mechanical erosion. No significant changes in the tested surface were observed on samples fully submerged in wastewater (C-series). The results indicated that the observed pitting corrosion of samples placed above the surface of the wastewater was a consequence of the presence of bacteria in a wet hydrogen sulfide environment. The fluorescence in situ hybridization method showed that either the sludge taken from the wastewater, or from the surface of samples submerged in wastewater exhibited increased amounts of bacteria from the δ-proteobacteria class, indicating the presence of microorganisms involved in the reduction of sulfur or sulfate compounds. A new approach to microbiological evaluation by determining classes of bacteria may be a promising tool for evaluating wastewater in terms of aggressiveness and recognizing favorable corrosive conditions.

Electrospun Silica-Polyacrylonitrile Nanohybrids for Water Treatments.

In this work, the removal of NOM (natural organic matter) as represented by humic acid by means of electrospun nanofiber adsorptive membranes (ENAMs) is described. Polyacrylonitrile (PAN) was used for the preparation of ENAMs incorporating silica nanoparticles as adsorbents. The addition of silica to the polymer left visible changes on the structural morphology and fibers' properties of the membrane. The membrane samples were characterized by pure water permeability, contact angle measurement, SEM, XPS, and XRD. This study assesses the preliminary performance of PAN-Si membranes for the removal of natural organic matter (NOM). The membrane rejected the humic acid, a surrogate of NOM, from 69.57% to 87.5%.

Removal of Zinc from Concentrated Galvanic Wastewater by Sodium Trithiocarbonate: Process Optimization and Toxicity Assessment.

In the present research, the removal of zinc from concentrated galvanic wastewater (pH 3.1, conductivity 20.31 mS/cm, salinity, 10.16 g/L, Chemical Oxygen Demand (COD) 2900 mg O2/L, Total Organic Carbon (TOC) 985 mg/L, zinc (Zn) 1534 mg/L and ethylenediaminetetraacetic acid (EDTA) 70 mg/L) by combination of lime (Ca(OH)2) and sodium trithiocarbonate (Na2CS3) as precipitation agents is studied. Central Composite Design (CCD) and response surface methodology (RSM) were applied for modelling and optimizing the designed wastewater treatment process. Analysis of Variance (ANOVA) and the experimental verification of the model confirmed the consistency of the experimental and estimated data calculated from the model (R2 = 0.9173, R2adj. = 0.8622). The use of Ca(OH)2 and Na2CS3 in the optimal condition calculated from the model (pH = 10.75 ± 0.10, V Na2CS3 dose 0.043 mL/L and time = 5 min) resulted in a decrease in the concentration of Zn in treated wastewater by 99.99%. Other physicochemical parameters of wastewater also improved. Simultaneously, the application of Ca(OH)2 and Na2CS3 reduced the inhibition of activated sludge dehydrogenase from total inhibition (for raw wastewater) to -70% (for treated wastewater). Under the same conditions the phytotoxicity tests revealed that the seed germination index for the raw and treated wastewater increased from 10% to 50% and from 90% to 100% for white mustard (Sinapis alba) and garden cress (Lepidium sativum L.), respectively. The parameters of root and shoot growth showed a statistically significant improvement. Treated wastewater (1:10) showed a stimulating effect (shoot growth) compared to the control sample (GI = -116.7 and -57.9 for S. alba and L. sativum L., respectively). Thus, the use of Na2CS3 is a viable option for the treatment of concentrated galvanic wastewater containing zinc.

Treatment of electropolishing industrial wastewater and its impact on the immobilisation of Daphnia magna.

The amount of industrial pollution entering the environment and its impact on living organisms is an ongoing concern. At the same time, due to an increasing awareness, new methods of wastewater treatment are being explored that are not only effective but also environmentally acceptable. Meeting environmental standards for permitted concentrations is a necessity, but investigating the effects of wastewater on living organisms is also an important issue. In this paper, the influence of metal ions (Fe(III), Cr(III), Ni(II), Cu(II)) in industrial wastewater from electropolishing of stainless steel on Daphnia magna has been investigated. Daphnids have been exposed to wastewater both before and after treatment (Ca(OH)2 precipitation, sorption with peat). Immobilisation in a 48-h acute toxicity test and EC50 has been determined. In the case of studied industrial wastewater, the organic content (expressed as total organic carbon) of the effluent has a positive impact in terms of the survival of D. magna and increases the range of heavy metal concentrations tolerated by them. The application of a two-stage process with Ca(OH)2 neutralisation followed by sorption with peat allows for the removal of almost 100% of metal ions from the wastewater. The reduction obtained ensured a limited impact on D. magna and a decrease in immobilisation to less than 10%. Proper execution of the wastewater treatment process ensures a reduction of its negative impact on living organisms.

A multi-factorial mathematical model for the selection of electropolishing parameters with a view to reducing the environmental impact.

Electrochemical metal processing is a process that generates harmful pollution. An important goal often disregarded by researchers is not only the achievement of the best possible quality of electropolished surface, but also minimising the load of metal ions in the wastewater generated in the process. The conducted experiments on the electropolishing of stainless steel in laboratory conditions, varied time, temperature and current density conditions, as well as process bath contamination (ranging from 0 to 6% Fe mass) allowed us to develop a multi-factorial mathematical model. This model offers the possibility of being able to select the process parameters recommended for achieving the desired effects. It takes into account such surface quality parameters as roughness and gloss, process duration and current density that determine power consumption, as well as the weight loss of the electropolished element that influence the rate of contamination in processing baths and wastewater. The study presents the composition of a passive film of stainless steel after the electropolishing process at the initial and final stages of the process bath's exploitation. The results obtained from XPS tests were then correlated with the results of corrosion tests and resistance to pitting corrosion in the environment of 0.1 M NaCl.

Effects of drought on environmental health risk posed by groundwater contamination.

This publication presents a comparison of the content of pollutants in groundwater samples taken at 117 measurement points in four regions of Poland during a drought period and in the reference period without drought. Based on the chemical analyses of water, an assessment of the health risk resulting from the use of underground water for consumption was carried out. The study aimed to determine whether drought affects the increase in health risk exposure of the population. It was found that despite the occurrence of drought, the expected increase in the concentration of pollutants in water does not take place in all locations. This study found that in some cases the occurrence of drought did not cause an increase in the non-cancerogenic threat expressed by the hazard index. There were also no clear changes in excess lifetime cancer risk values except for selected measurement points. On the other hand, the statistical analysis of all data collected in the regions where the research was conducted showed a general trend of increasing environmental health risk caused by changes in groundwater pollution during drought.

Electrochemical Polishing of Austenitic Stainless Steels.

Improvement of the corrosion resistance capability, surface roughness, shining of stainless-steel surface elements after electrochemical polishing (EP) is one of the most important process characteristics. In this paper, the mechanism, obtained parameters, and results were studied on electropolishing of stainless-steel samples based on the review of the literature. The effects of the EP process parameters, especially current density, temperature, time, and the baths used were presented and compared among different studies. The samples made of stainless steel presented in the articles were analysed in terms of, among other things, surface roughness, resistance to corrosion, microhardness, and chemical composition. All results showed that the EP process greatly improved the analysed properties of the stainless-steel surface elements.

Portable Analyzer for On-Site Determination of Dissolved Organic Carbon-Development and Field Testing.

Dissolved organic carbon (DOC) is a sum parameter that is frequently used in water analytics. Highly resolved and accurate DOC data are necessary, for instance, for water quality monitoring and for the evaluation of the efficiency of treatment processes. The conventional DOC determination methods consist of on-site sampling and subsequent analysis in a stationary device in a laboratory. However, especially in regions where no or only poorly equipped laboratories are available, this method bears the risk of getting erroneous results. For this reason, the objective of the present study was to set up a reliable and portable DOC analyzer for on-site analysis. The presented DOC system is equipped with an electrolysis-based decomposition cell with boron-doped diamond electrodes (BDD) that oxidizes the organic compounds to carbon dioxide. Within this study, the influence of different electrode materials and the composition of the applied electrolytes on the DOC decomposition in an undivided electrolytic cell were systematically investigated. Furthermore, some technical aspects of the portable prototype are discussed. After a detailed validation, the prototype was used in an ongoing monitoring program in Northern India. The limit of detection is 0.1 mg L-1 C with a relative standard deviation of 2.3% in a linear range up to 1000 mg L C-1. The key features of the portable DOC analyzer are: No need for ultra-pure gases, catalysts or burning technology, an analyzing time per sample below 5 min, and a reliable on-site DOC determination.

Environmental health risk posed by contamination of the individual water wells.

This paper presents the results of analyzes of water samples taken from individual water wells intended for supplying households in non-urbanized areas with low population and infrastructure density. Relatively high concentrations of harmful pollutants were found in ground waters of the examined spots located in the suburban areas which may increase the risk of health incidents in exposed populations. Based on long-term measurements carried out in individual spots and toxicological data, the individual health risks related to carcinogenic effects in humans were assessed, resulting from direct ingestion of such water and from dermal contact. Non-carcinogenic hazard levels were determined, as well. In this work a novel approach to health risk assessment was proposed. It consists of determining the risks that range between minimum and possible maximum values. In the case of limited traceability of a pollutant the maximum and minimum risk values were derived from the limit of quantification (LOQ). Thus, for the minimum risk, zero concentration was applied, while for calculation of the maximum risk, LOQ was used as the possible highest pollutant content in water. The calculations proved that using untreated water for consumption and bathing is likely to cause an increase of both mutagenic and toxic risk in humans concerned. Depending on the site, the calculated non-carcinogenic hazard level expressed by the hazard index HI ranges between 0.6 and 3.6 while the excess lifetime cancer risk ELCR is of the order of 10-4.