RESUMEN
This work proposes a novel drying method suitable for probiotic bacteria, called flash freeze-drying (FFD), which consists of a cyclic variation in pressure (up-down) in a very short time and is applied during primary drying. The effects of three FFD temperatures (-25 °C, -15 °C, and -3 °C) on the bacterial survival and water activity of Lactobacillus acidophilus LA5 (LA), previously microencapsulated with calcium alginate and chitosan, were evaluated. The total process time was 900 min, which is 68.75% less than the usual freeze-drying (FD) time of 2880 min. After FFD, LA treated at -25 °C reached a cell viability of 89.94%, which is 2.74% higher than that obtained by FD, as well as a water activity of 0.0522, which is 55% significantly lower than that observed using FD. Likewise, this freezing temperature showed 64.72% cell viability at the end of storage (28 days/20 °C/34% relative humidity). With the experimental data, a useful mathematical model was developed to obtain the optimal FFD operating parameters to achieve the target water content in the final drying.
RESUMEN
Injecting ozone by means of a venturi device causes an increase in the mass transfer coefficient with respect to gas dissolution through a microdiffuser. Moreover, it was observed that significant turbidity levels are not formed (<1 NTU) when using a microdiffuser, probably due to the relatively high stirring which avoids formation of intermolecular hydrogen bonds. On the contrary, employing a venturi injector led to the production of high turbidity levels in water (up to 20 NTU). This indicates that formation of supramolecular structures causing this turbidity requires the presence of certain facilitating species which are formed through ozone decomposition mechanisms. The maximum ozone transfer takes place when operating at pH0 9.0, that is, when this value is close to the pKa and employing a dose of R = 115 mol O3/mol Pa0. Under these conditions, the degradation of paracetamol generates color, which is attributed to the presence of condensation products from pyrogallol, catechol, resorcinol, acetamide, oxalic acid and 4-aminophenol. Once paracetamol is fully degraded and solution turns colorless, turbidity grows (>20 NTU). This is attributed to formation of high molecular weight structures from 4-aminophenol and oxamide. Operating with large ozone excess (R = 500 mol O3/mol Pa0), the maximum ozone transfer rate is achieved at pH0 = 12.0. Under these conditions, the pollutant is fully removed together with water aromaticity and oxalic acid (able to form linear structures through hydrogen bonding) is detected during color development. Then, turbidity is formed due to cyclic dimer formation from acetic acid.
RESUMEN
This work presents an efficient method for treating industrial wastewater containing aniline and benzothiazole, which are refractory to conventional treatments. A combination of heterogeneous photocatalysis operating in a fluidised bed reactor is studied in order to increase mass transfer and reduce reaction times. This process uses a manganese dioxide catalyst supported on granular activated carbon with environmentally friendly characteristics. The manganese dioxide composite is prepared by hydrothermal synthesis on carbon Hydrodarco® 3000 with different active phase ratios. The support, the metal oxide, and the composite are characterised by performing Brunauer, Emmett, and Teller analysis, transmission electron microscopy, X-ray diffraction analysis, X-ray fluorescence analysis, UV-Vis spectroscopy by diffuse reflectance, and Fourier transform infrared spectroscopy in order to evaluate the influence of the metal oxide on the activated carbon. A composite of MnO2/GAC (3.78% in phase α-MnO2) is obtained, with a 9.4% increase in the specific surface of the initial GAC and a 12.79 nm crystal size. The effect of pH and catalyst load is studied. At a pH of 9.0 and a dose of 0.9 g L-1, a high degradation of aniline and benzothiazole is obtained, with an 81.63% TOC mineralisation in 64.8 min.
RESUMEN
In this work, binary and ternary gas mixtures of 1,3,3,3-tetrafluoropropene, HFO-1234ze(E), and perfluoro-(3-methylbutan-2-one), CF3C(O)CF(CF3)2, with CO2 and synthetic air, are presented as alternatives to SF6 in medium-voltage electrical equipment. They were used in four medium-voltage switchgear cubicles replacing SF6 gas, and after a period of time, under permanent 30 kV AC voltage, gas mixture samples were extracted and analyzed on the same day using a validated methodology based on gas chromatography (GC) coupled to mass spectrometry (MS) and thermal conductivity (TCD). CF4 (tetrafluoromethane), C2F6 (hexafluoroethane), C3F6 (hexafluoropropylene), C3HF7 (1,1,1,2,2,3,3-heptafluoropropane), CH2F2 (difluoromethane), and the cis and trans-C3H2F4 (1,3,3,3-tetrafluoropropene) have been identified as decomposition products in these gas mixtures. In addition, a quantity of water has been observed, as well as CO in one of the cubicles. The most abundant decomposition products identified in gas mixture samples (C3HF7 and C3F6) together with water and CO content have been quantified using commercial gas mixture reference standards. The toxicity and global warming of the analyzed compounds are evaluated to determine the most adequate gas mixture among those studied as a candidate to substitute SF6.
RESUMEN
This work develops a kinetic model that allow to predict the water toxicity and the main degradation products concentration of aqueous solutions containing 4-chlorophenol oxidised by UV/H2O2. The kinetic model was developed grouping degradation products of similar toxicological nature: aromatics (hydroquinone, benzoquinone, 4-chlorocatechol and catechol), aliphatics (succinic, fumaric, maleic and malonic acids) and mineralised compounds (oxalic, acetic and formic acids). The degradation of each group versus time was described as a mathematical function of the rate constant of a second-order reaction involving the hydroxyl radical, the quantum yield of lump, the concentration of the hydroxyl radicals and the intensity of the emitted UV radiation. The photolytic and kinetic parameters characterising each lump were adjusted by experimental assays. The kinetic, mass balance and toxicity equations were solved using the Berkeley Madonna numerical calculation tool. Results showed that 4-chlorophenol would be completely removed during the first hour of the reaction, operating with oxidant molar ratios higher than R = 200 at pH 6.0 and UV = 24 W. Under these conditions, a decrease in the rate of total organic carbon (TOC) removal close to 50% from the initial value was observed. The solution colour, attributed to the presence of oxidation products as p-benzoquinone and hydroquinone, were oxidised to colourless species, that resulted in a decrease in the toxicity of the solutions (9.95 TU) and the aromaticity lost.
RESUMEN
This paper presents an intensification study of an ozonation process through an ultrasonic pre-treatment for the elimination of humic substances in water and thus, improve the quality of water treatment systems for human consumption. Humic acids were used as representative of natural organic matter in real waters which present low biodegradability and a high potential for trihalomethane formation. Ultrasonic frequency (98 kHz, 300 kHz and 1 MHz), power (10-40 W) and sonicated volume (150-400 mL) was varied to assess the efficiency of the ultrasonic pre-treatment in the subsequent ozonation process. A direct link between hydroxyl radical (HO) formation and fluorescence reduction was observed during sonication pre-treatment, peaking at 300 kHz and maximum power density. Ultrasound, however, did not reduce total organic carbon (TOC). Injected ozone (O3) dose and reaction time were also evaluated during the ozonation treatment. With 300 kHz and 40 W ultrasonic pre-treatment and the subsequent ozonation step (7.4 mg O3/Lgas), TOC was reduced from 21 mg/L to 13.5 mg/L (36% reduction). HO attack seems to be the main degradation mechanism during ozonation. A strong reduction in colour (85%) and SUVA254 (70%) was also measured. Moreover, changes in the chemical structure of the macromolecule were observed that led to the formation of oxidation by-products of lower molecular weight.
