Measuring the Diameter of Single-Wall Carbon Nanotubes Using AFM.

In this work, we identify two issues that can significantly affect the accuracy of AFM measurements of the diameter of single-wall carbon nanotubes (SWCNTs) and propose a protocol that reduces errors associated with these issues. Measurements of the nanotube height under different applied forces demonstrate that even moderate forces significantly compress several different types of SWCNTs, leading to errors in measured diameters that must be minimized and/or corrected. Substrate and nanotube roughness also make major contributions to the uncertainty associated with the extraction of diameters from measured images. An analysis method has been developed that reduces the uncertainties associated with this extraction to <0.1 nm. This method is then applied to measure the diameter distribution of individual highly semiconducting enriched nanotubes in networks prepared from polyfluorene/SWCNT dispersions. Good agreement is obtained between diameter distributions for the same sample measured with two different commercial AFM instruments, indicating the reproducibility of the method. The reduced uncertainty in diameter measurements based on this method facilitates: (1) determination of the thickness of the polymer layer wrapping the nanotubes and (2) measurement of nanotube compression at tube-tube junctions within the network.

Surface chemistry of metal oxide nanoparticles: NMR and TGA quantification.

Surface functionalization is widely used to control the behavior of nanomaterials for a range of applications. However, methods to accurately quantify surface functional groups and coatings are not yet routinely applied to nanomaterial characterization. We have employed a combination of quantitative NMR (qNMR) and thermogravimetric analysis (TGA) to address this problem for commercial cerium, nickel, and iron oxide nanoparticles (NPs) that have been modified to add functional coatings with (3-aminopropyl)triethoxysilane (APTES), stearic acid, and polyvinylpyrrolidone (PVP). The qNMR method involves quantification of material that is released from the NPs and quantified in the supernatant after removal of NPs. Removal of aminopropylsilanes was accomplished by basic hydrolysis whereas PVP and stearic acid were removed by ligand exchange using sodium hexametaphosphate and pentadecafluorooctanoic acid, respectively. The method accuracy was confirmed by analysis of NPs with a known content of surface groups. Complementary TGA studies were carried out in both air and argon atmosphere with FT-IR of evolved gases in argon to confirm the identity of the functional groups. TGA measurements for some unfunctionalized samples show mass loss due to unidentified components which makes quantification of functional groups in surface-modified samples less reliable. XPS provides information on the presence of surface contaminants and the level of surface hydroxylation for selected samples. Despite the issues associated with accurate quantification using TGA, the TGA estimates agree reasonably well with the qNMR data for samples with high surface loading. This study highlights the issues in analysis of commercial nanomaterials and is an advance towards the development of generally applicable methods for quantifying surface functional groups.

A Multi-Method Approach for Quantification of Surface Coatings on Commercial Zinc Oxide Nanomaterials.

Surface functionalization is a key factor for determining the performance of nanomaterials in a range of applications and their fate when released to the environment. Nevertheless, it is still relatively rare that surface groups or coatings are quantified using methods that have been carefully optimized and validated with a multi-method approach. We have quantified the surface groups on a set of commercial ZnO nanoparticles modified with three different reagents ((3-aminopropyl)-triethoxysilane, caprylsilane and stearic acid). This study used thermogravimetric analysis (TGA) with Fourier transform infrared spectroscopy (FT-IR) of evolved gases and quantitative solution 1H nuclear magnetic resonance (NMR) for quantification purposes with 13C-solid state NMR and X-ray photoelectron spectroscopy to confirm assignments. Unmodified materials from the same suppliers were examined to assess possible impurities and corrections. The results demonstrate that there are significant mass losses from the unmodified samples which are attributed to surface carbonates or residual materials from the synthetic procedure used. The surface modified materials show a characteristic loss of functional group between 300-600 °C as confirmed by analysis of FT-IR spectra and comparison to NMR data obtained after quantitative release/extraction of the functional group from the surface. The agreement between NMR and TGA estimates for surface loading is reasonably good for cases where the functional group accounts for a relatively large fraction of the sample mass (e.g., large groups or high loading). In other cases TGA does not have sufficient sensitivity for quantitative analysis, particularly when contaminants contribute to the TGA mass loss. X-ray photoelectron spectroscopy and solid state NMR for selected samples provide support for the assignment of both the functional groups and some impurities. The level of surface group loading varies significantly with supplier and even for different batches or sizes of nanoparticles from the same supplier. These results highlight the importance of developing reliable methods to detect and quantify surface functional groups and the importance of a multi-method approach.

Quantification of amine functional groups on silica nanoparticles: a multi-method approach.

Surface chemistry is an important factor for quality control during production of nanomaterials and for controlling their behavior in applications and when released into the environment. Here we report a comparison of four methods for quantifying amine functional groups on silica nanoparticles (NPs). Two colorimetric assays are examined, ninhydrin and 4-nitrobenzaldehyde, which are convenient for routine analysis and report on reagent accessible amines. Results from the study of a range of commercial NPs with different sizes and surface loadings show that the assays account for 50-100% of the total amine content, as determined by dissolution of NPs under basic conditions and quantification by solution-state 1H NMR. To validate the surface quantification by the colorimetric assays, the NPs are modified with a trifluoromethylated benzaldehyde probe to enhance sensitivity for quantitative 19F solid state NMR and X-ray photoelectron spectroscopy (XPS). Good agreement between the assays and the determination from solid-state NMR is reinforced by elemental ratios from XPS, which indicate that in most cases the difference between total and accessible amine content reflects amines that are outside the depth probed by XPS. Overall the combined results serve to validate the relatively simple colorimetric assays and indicate that the reactions are efficient at quantifying surface amines, by contrast to some other covalent modifications that have been employed for functional group quantification.

Versatile Molecular Silver Ink Platform for Printed Flexible Electronics.

A silver molecular ink platform formulated for screen, inkjet, and aerosol jet printing is presented. A simple formulation comprising silver neodecanoate, ethyl cellulose, and solvent provides improved performance versus that of established inks, yet with improved economics. Thin, screen-printed traces with exceptional electrical (<10 mΩ/□/mil or 12 µΩ·cm) and mechanical properties are achieved following thermal or photonic sintering, the latter having never been demonstrated for silver-salt-based inks. Low surface roughness, submicron thicknesses, and line widths as narrow as 41 µm outperform commercial ink benchmarks based on flakes or nanoparticles. These traces are mechanically robust to flexing and creasing (less than 10% change in resistance) and bind strongly to epoxy-based adhesives. Thin traces are remarkably conformal, enabling fully printed metal-insulator-metal band-pass filters. The versatility of the molecular ink platform enables an aerosol jet-compatible ink that yields conductive features on glass with 2× bulk resistivity and strong adhesion to various plastic substrates. An inkjet formulation is also used to print top source/drain contacts and demonstrate printed high-mobility thin film transistors (TFTs) based on semiconducting single-walled carbon nanotubes. TFTs with mobility values of ∼25 cm2 V-1 s-1 and current on/off ratios >104 were obtained, performance similar to that of evaporated metal contacts in analogous devices.

Fully Printed and Encapsulated SWCNT-Based Thin Film Transistors via a Combination of R2R Gravure and Inkjet Printing.

Fully printed thin film transistors (TFT) based on poly(9,9-di-n-dodecylfluorene) (PFDD) wrapped semiconducting single walled carbon nanotube (SWCNT) channels are fabricated by a practical route that combines roll-to-roll (R2R) gravure and ink jet printing. SWCNT network density is easily controlled via ink formulation (concentration and polymer:CNT ratio) and jetting conditions (droplet size, drop spacing, and number of printed layers). Optimum inkjet printing conditions are established on Si/SiO2 in which an ink consisting of 6:1 PFDD:SWCNT ratio with 50 mg L-1 SWCNT concentration printed at a drop spacing of 20 µm results in TFTs with mobilities of ∼25 cm2 V-1 s-1 and on-/off-current ratios > 105. These conditions yield excellent network uniformity and are used in a fully additive process to fabricate fully printed TFTs on PET substrates with mobility values > 5 cm2 V-1 s-1 (R2R printed gate electrode and dielectric; inkjet printed channel and source/drain electrodes). An inkjet printed encapsulation layer completes the TFT process (fabricated in bottom gate, top contact TFT configuration) and provides mobilities > 1 cm2 V-1 s-1 with good operational stability, based on the performance of an inverter circuit. An array of 20 TFTs shows that most have less than 10% variability in terms of threshold voltage, transconductance, on-current, and subthreshold swing.

Analysis Method for Quantifying the Morphology of Nanotube Networks.

While atomic force microscopy (AFM) is a powerful technique for imaging assemblies and networks of nanoscale materials, approaches for quantitative assessment of the morphology of these materials are lacking. Here we present a volume-based approach for analyzing AFM images of assemblies of nano-objects that enables the extraction of relevant parameters describing their morphology. Random networks of single-walled carbon nanotubes (SWCNTs) deposited via solution-phase processing are used as an example to develop the method and demonstrate its utility. AFM imaging shows that the morphology of these networks depends on details of processing and is influenced by choice of substrate, substrate cleaning method, and postdeposition rinsing protocols. A method is outlined to analyze these images and extract relevant parameters describing the network morphology such as the density of SWCNTs and the degree to which tubes are bundled. Because this volume-based approach depends on accurate measurements of the height of individual tubes and their networks, a procedure for obtaining reliable height measurements is also discussed. Obtaining quantitative parameters that describe the network morphology allows going beyond qualitative descriptions of images and will facilitate optimizing network preparation methods based on measurable criteria and correlating performance with morphology.

Enrichment of large-diameter semiconducting SWCNTs by polyfluorene extraction for high network density thin film transistors.

A systematic study on the use of 9,9-dialkylfluorene homopolymers (PFs) for large-diameter semiconducting (sc-) single-walled carbon nanotube (SWCNT) enrichment is the focus of this report. The enrichment is based on a simple three-step extraction process: (1) dispersion of as-produced SWCNTs in a PF solution; (2) centrifugation at a low speed to separate the enriched sc-tubes; (3) filtration to collect the enriched sc-SWCNTs and remove excess polymer. The effect of the extraction conditions on the purity and yield including molecular weight and alkyl side-chain length of the polymers, SWCNT concentration, and polymer/SWCNT ratio have been examined. It was observed that PFs with alkyl chain lengths of C10, C12, C14, and C18, all have an excellent capability to enrich laser-ablation sc-SWCNTs when their molecular weight is larger than ∼10 000 Da. More detailed studies were therefore carried out with the C12 polymer, poly(9,9-di-n-dodecylfluorene), PFDD. It was found that a high polymer/SWCNT ratio leads to an enhanced yield but a reduced sc-purity. A ratio of 0.5-1.0 gives an excellent sc-purity and a yield of 5-10% in a single extraction as assessed by UV-vis-NIR absorption spectra. The yield can also be promoted by multiple extractions while maintaining high sc-purity. Mechanistic experiments involving time-lapse dispersion studies reveal that m-SWCNTs have a lower propensity to be dispersed, yielding a sc-SWCNT enriched material in the supernatant. Dispersion stability studies with partially enriched sc-SWCNT material further reveal that m-SWCNTs : PFDD complexes will re-aggregate faster than sc-SWCNTs : PFDD complexes, providing further sc-SWCNT enrichment. This result confirms that the enrichment was due to the much tighter bundles in raw materials and the more rapid bundling in dispersion of the m-SWCNTs. The sc-purity is also confirmed by Raman spectroscopy and photoluminescence excitation (PLE) mapping. The latter shows that the enriched sc-SWCNT sample has a narrow chirality and diameter distribution dominated by the (10,9) species with d = 1.29 nm. The enriched sc-SWCNTs allow a simple drop-casting method to form a dense nanotube network on SiO2/Si substrates, leading to thin film transistors (TFTs) with an average mobility of 27 cm(2) V(-1) s(-1) and an average on/off current ratio of 1.8 × 10(6) when considering all 25 devices having 25 µm channel length prepared on a single chip. The results presented herein demonstrate how an easily scalable technique provides large-diameter sc-SWCNTs with high purity, further enabling the best TFT performance reported to date for conjugated polymer enriched sc-SWCNTs.

Highly sensitive electrical detection of TCNE on chemically passivated silicon-on-insulator.

Adsorption of tetracyanoethylene (TCNE) onto hydrogen terminated, n-type silicon-on-insulator is shown to cause significant depletion of majority carriers. Employing an ambient pseudo-MOSFET, ppm levels of TCNE vapour rapidly decrease the n-channel saturation current by at least two orders of magnitude. Covalent passivation with a decyl monolayer improves the reversibility of the response while only slightly decreasing the sensitivity.

Diazonium-derived aryl films on gold nanoparticles: evidence for a carbon-gold covalent bond.

Tailoring the surface chemistry of metallic nanoparticles is generally a key step for their use in a wide range of applications. There are few examples of organic films covalently bound to metal nanoparticles. We demonstrate here that aryl films are formed on gold nanoparticles from the spontaneous reduction of diazonium salts. The structure and the bonding of the film is probed with surface-enhanced Raman scattering (SERS). Extinction spectroscopy and SERS show that a nitrobenzene film forms on gold nanoparticles from the corresponding diazonium salt. Comparison of the SERS spectrum with spectra computed from density functional theory models reveals a band characteristic of a Au-C stretch. The observation of this stretch is direct evidence of a covalent bond. A similar band is observed in high-resolution electron energy loss spectra of nitrobenzene layers on planar gold. The bonding of these types of films through a covalent interaction on gold is consistent with their enhanced stability observed in other studies. These findings provide motivation for the use of diazonium-derived films on gold and other metals in applications where high stability and/or strong adsorbate-substrate coupling are required.

Electro-optic investigation of the surface trapping efficiency in n-alkanethiol SAM passivated GaAs(001).

The electro-optic characteristics of the semi-insulating and n(+)-type GaAs(001) surfaces passivated with n-alkanethiol self-assembled monolayers were investigated using Kelvin probe surface photovoltage (SPV) and photoluminescence (PL) techniques. Referencing the equilibrium surface barrier height established in an earlier report, SPV measurements demonstrated a significant (>100 mV) increase in the non-equilibrium band-bending potential observed under low-level photo-injection. Modeling of the SPV accounts for these observations in terms of a large (>10(4)) decrease in the hole/electron ratio of surface carrier capture cross-sections, which is suggested to result from the electrostatic potential of the interfacial dipole layer formed upon thiol chemisorption. The cross-section effects are verified in the high-injection regime based on carrier transport modeling of the PL enhancement manifested as a reduction of the surface recombination velocity.

Molecular modulation of conductivity on H-terminated silicon-on-insulator substrates.

The adsorption of a range of molecular species (water, pyridine, and ammonia) is found to reversibly modulate the conductivity of hydrogen-terminated silicon-on-insulator (H-SOI) substrates. Simultaneous sheet-resistance and Hall-effect measurements on moderately doped (10(15) cm(-3)) n- and p-type H-SOI samples mounted in a vacuum system are used to monitor the effect of gas exposure in the Torr range on the electrical-transport properties of these substrates. Reversible physisorption of "hole-trapping" species, such as pyridine (C(5)H(5)N) and ammonia (NH(3)) produces highly conductive minority-carrier channels (inversion) on p-type substrates, mimicking the action of a metallic gate in a field-effect transistor. The adsorption of these same molecules on n-type SOI induces strong electron-accumulation layers. Minority/majority channels are also formed upon controlled exposure to water vapor. These observations can be explained by a classical band-bending model, which considers the adsorbates as the source of a uniform surface charge ranging from +10(11) to +10(12)q cm(-2). These results demonstrate the utility of DC transport measurements of SOI platforms for studies of molecular adsorption and charge-transfer effects at semiconductor surfaces.

Direct stabilization of a phospholipid monolayer on H-terminated silicon.

This Article describes a strategy to stabilize a phospholipid monolayer directly on the surface of a H-terminated silicon substrate in order to provide a useful platform for silicon based biosensors. The stabilization of an acrylated phospholipid monolayer is obtained by two-dimensional chain polymerization. As the formation of the lipid monolayer in aqueous solution competes with the oxidation of the silicon surface, several cycles of oxide removal and lipid exposure are necessary to densify the lipid layer. Lipid monolayer formation is followed by Fourier transform infrared spectroscopy. The resulting monolayer is denser than corresponding alkyl monolayers formed on H-terminated silicon via photochemical or thermally initiated reactions.

Surface dipole layer potential induced ir absorption enhancement in n-alkanethiol SAMs on GaAs(001).

The work function of n-alkanethiol self-assembled monolayers (SAMs) prepared on the GaAs(001) surface was measured using the Kelvin probe technique yielding the SAM 2D dipole layer potential (DLP). Direct n-dependent proportionality between the DLP values and the C-H stretching mode infrared (IR) absorption intensities was observed, which supports a correspondence of reported IR enhancements with the electrostatic properties of the interface. X-ray photoelectron spectroscopy is also used to verify the work function measurements. In addition, the principal components of the refractive index tensor are shown to be n-invariant in the ordered SAM phase. Our results suggest that a local field correction to the transition dipole moment accounts for the observed increase in IR activity through an increase to the electronic polarizability.

Evidence for initiation of thermal reactions of alkenes with hydrogen-terminated silicon by surface-catalyzed thermal decomposition of the reactant.

New insights into the mechanism of thermal reactions of alkenes with hydrogen terminated silicon are presented. Scanning tunneling microscopy (STM) imaging at the early stages of the reaction of 1-decene with H/Si(111) at 150 degrees C confirm this reaction occurs via a propagating radical chain mechanism. In addition, evidence is presented for an initiation mechanism involving degradation of hydrocarbon molecules catalyzed by the silanol surface of Schlenk tubes commonly used in carrying out these reactions. Hydrogen-terminated silicon surfaces are found to be unstable in the "inert" solvent dodecane when heated at 150 degrees C in a Pyrex Schlenk tube. By contrast, the surfaces were significantly more stable at the same temperature when reactions were carried out in Teflon (polytetrafluoroethylene or PTFE). The thermal reaction of decene with H/Si(111) was found to proceed more rapidly in Pyrex than in PTFE, consistent with an impurity-based initiation mechanism.

Sequential reactions with amine-terminated monolayers and isolated molecules on H/Si(111).

A simple method for preparing monolayers with terminal amine functionality is demonstrated. A gas-phase photochemical reaction of 1,3-diaminopropane with a H-terminated Si(111) surface results in the molecules covalently attaching to the surface, primarily through the formation of a Si--N bond. These monolayers are characterized by scanning tunneling microscopy (STM) and high-resolution electron energy loss spectroscopy (HREELS). The reactivity of the terminal amine is confirmed by exposing the monolayer to benzaldehyde, resulting in the formation of an imine link and the grafting of phenyl rings onto the surface. For short irradiation times, this reaction leads to the formation of isolated amine groups on an otherwise pristine H-terminated surface. STM and HREELS studies of the benzaldehyde reaction on these low-coverage surfaces (less than 0.005 monolayers) indicate that the reaction is restricted to the reactive amine groups, leaving the remainder of the surface unaffected. This simple approach for a sequential coupling reaction is expected to facilitate attachment of more complex molecules (molecular switches, biomolecules) for single-molecule STM studies.

Reaction of alkenes with hydrogen-terminated and photooxidized silicon surfaces. A comparison of thermal and photochemical processes.

Reagentless micropatterning of hydrogen-terminated Si(111) via UV irradiation through a photomask has proven to be a convenient strategy for the preparation of ordered bicomponent monolayers. The success of this technique relies upon the differential rate of reaction of an alkene with the hydrogen-terminated and photooxidized regions of the surface. Monolayer formation can be accomplished under either thermal or photochemical conditions. It was observed that, after 3 h, reaction in neat alkene solution irradiation (Rayonet, 300 nm) afforded the expected patterned surface, while thermal conditions (150 degrees C) resulted in a partial loss of pattern fidelity. Monolayer properties and formation were studied on oxidized and hydrogen-terminated silicon under thermal and photochemical initiation, by contact angle, ellipsometry, Fourier transform infrared spectroscopy, high-resolution electron energy loss spectroscopy, and X-ray photoelectron spectroscopy. Results show that alkenes add to silanol groups on the silica surface in a manner consistent with acid catalysis: once attached to the surface, the silica oxidized the hydrocarbon.

Formation of organic monolayers on silicon via gas-phase photochemical reactions.

A new method for the formation of molecular monolayers on silicon surfaces utilizing gas-phase photochemical reactions is reported. Hydrogen-terminated Si(111) surfaces were exposed to various gas-phase molecules (hexene, benzaldehyde, and allylamine) and irradiated with ultraviolet light from a mercury lamp. The surfaces were studied with in situ Fourier transform infrared spectroscopy, high-resolution electron energy loss spectroscopy, and scanning tunneling microscopy. The generation of gas-phase radicals was found to be the initiator for organic monolayer formation via the abstraction of hydrogen from the H/Si(111) surface. Monolayer growth can occur through either a radical chain reaction mechanism or through direct radical attachment to the silicon dangling bonds.

Kinetic control of the photochemical reactivity of hydrogen-terminated silicon with bifunctional molecules.

Carboxy-terminated crystalline silicon surfaces are of fundamental importance for biochip fabrication because of their reactivity toward biological macromolecules. To explore the feasibility of direct attachment of bifunctional molecules (e.g., omega-alkenoic acids) to hydrogen-terminated silicon crystal (H-Si) via Si-C linkages, we have investigated the photoreactivities of the alkene (-CH=CH(2)) and carboxy (-COOH) terminal groups of 1-dodecene, undecanoic acid, and undecylenic acid toward H-Si. The alkene terminus was found to react substantially faster than the carboxy terminus under UV irradiation (at 350 nm). By controlling the reaction time, high-quality carboxy-terminated monolayers, comparable to those formed by ester hydrolysis, can be obtained from a direct, one-step photochemical reaction between H-Si and undecylenic acid.

Selective adsorption of pyridine at isolated reactive sites on Si(100).

Dative bonding of nitrogen-containing heterocycles offers a strategy for the controlled attachment of aromatic molecules to silicon surfaces. However, while scanning tunneling microscopy shows that pyridine on clean Si(100) initially binds via a dative bonding configuration, slow conversion to a more stable bridging state, destroying the aromaticity, is observed. To restrict adsorption to the dative bonded form, we investigated the interaction of pyridine with isolated reactive sites on partially H-terminated Si(100). While dative bonding on isolated clean dimers is observed, single dangling bonds remain unreacted. This selectivity can be accounted for by the ability of the Si-Si dimers to act as electron acceptors that stabilize the dative bonded species. This observation has important implications for the controlled positioning of single molecules on silicon via dative bonding.