Inhibitory effects of veterinary antibiotics on anammox activity: short- and long-term tests.

The suitability of the anammox process for the treatment of swine digester liquor was assessed through the evaluation of the short- and long-term inhibitory effect of three veterinary antibiotics commonly administered to Italian swine livestock. The toxicity of doxycycline, tiamulin and enrofloxacin was evaluated through batch tests designed to estimate specific anammox activity. Moreover, the short-term toxicity of combined concentrations of doxycycline and enrofloxacin was evaluated so as to verify whether a synergistic effect could be established. According to the inhibition recorded in the presence of the maximum antibiotics concentrations predicted for digester liquor, target compounds do not seem to represent a real hazard for anammox bacteria because at those concentration levels, the activity was just slightly reduced. Moreover, in granular systems, inhibition could be easily counterbalanced by increasing the biomass concentration in the reactor, thus assuring the design treatment capacity for antibiotic-rich wastewaters.

Physiological and kinetic characterization of a suspended cell anammox culture.

Anammox related technologies are currently widely applied for nitrogen removal from sewage sludge digester rejection water. Nevertheless, many aspects of the anammox process like the kinetic characteristics and the reaction stoichiometry are still subject of debate. Parameter values reported in literature are often hampered by mass transfer limitation or by the presence of a significant side population. In this study a membrane bioreactor (MBR) based method for growing a highly enriched anammox microbial community is described. The almost pure free-cells suspension of highly active anammox bacteria was used for detailed kinetic and stoichiometric analysis of the anammox process. The anammox culture enriched during this study had a biomass specific maximum growth rate of 0.21 d(-)(1) which is higher than ever reported before in literature. Using an experimental methodology based on imposing dynamic process conditions combined with process modeling and parameter estimation, the intrinsic nitrite half saturation constant was identified to be as low as 35 µg-N L(-)(1). This was confirmed to be an accurate estimation in the pH range of 6.8-7.5.

Ozonation effects for excess sludge reduction on bacterial communities composition in a full-scale activated sludge plant for domestic wastewater treatment.

Activated sludge process is the most widely diffused system to treat wastewater to control the discharge of pollutants into the environment. Microorganisms are responsible for the removal of organic matter, nitrogen, phosphorous and other emerging contaminants. The environmental conditions of biological reactors significantly affects the ecology of the microbial community and, therefore, the performance of the treatment process. In the last years, ozone has been used to reduce excess sludge production by wastewater treatment plants (WWTPs), whose disposal represents one of the most relevant operational costs. The ozonation process has demonstrated to be a viable method to allow a consistent reduction in excess sludge. This study was carried out in a full-scale plant treating municipal wastewater in two parallel lines, one ozonated in the digestion tank and another used as a control. Bacterial communities of samples collected from both lines of digestion thanks were then compared to assess differences related to the ozonation treatment. Data were then analysed with terminal restriction fragment length polymorphism (T-RFLP) analysis on 16S rRNA gene. Differences between bacterial communities of both treated and untreated line appeared 2 weeks after the beginning of the treatment. Results demonstrated that ozonation treatment significantly affected the activated sludge in WWTP.

Inhibition effect of swine wastewater heavy metals and antibiotics on anammox activity.

The feasibility of anaerobic ammonium oxidation (anammox) process to treat wastewaters containing antibiotics and heavy metals (such as the liquid fraction of the anaerobically digested swine manure) was studied in this work. The specific anammox activity (SAA) was evaluated by means of manometric batch tests. The effects of oxytetracycline, sulfathiazole, copper and zinc were studied. The experimental data of the short-term assays were fitted with an inhibition model to identify the half maximal inhibitory concentration (IC(50)). After 24 h exposures, IC(50)-values equal to 1.9, 3.9, 650 and 1,100 mg L(-1) were identified for copper, zinc, sulfathiazole and tetracycline respectively. The effect of prolonged exposure (14 days) to oxytetracycline and sulfathiazole was studied by means of repeated batch-assays. Anabolism and catabolism reactions were active during the inhibition tests indicating that anammox bacteria could grow even in the extreme conditions tested. Considering the average concentrations expected in swine wastewaters, the inhibitors studied do not seem to represent a problem for the application of the anammox process. However, in order to verify the effect of these compounds on the growth of anammox bacteria, continuous culture experiments could be conducted.

The effect of nitrite inhibition on the anammox process.

The negative effect of nitrite on anammox activity has been reported widely during the past decade. Although the adverse effect is clear, conflicting reports exist on the level at which it occurs and its reversible/irreversible nature. An in depth study on nitrite inhibition therefore was performed in which the influence of environmental factors was evaluated. Anammox activity was measured in anammox granules by continuously monitored standardized manometric batch tests extending the interpretation by evaluation of lag times, maximum conversion rates during the tests and substrates/product conversion ratios. The granules where obtained from a one-stage anammox reactor, the dominant anammox organisms belonged to the Brocadia type. The observed 50% activity inhibition for nitrite (IC(50)) was 0.4 g N L(-1). The activity recovered fully after removal of the nitrite. Conversion in fresh medium after exposure to up to 6 g NO(2)(-)-N L(-1) for 24 h showed less then 60% loss of activity. Presence of ammonium during nitrite (2 g N L(-1)) exposure resulted in a stronger loss of activity after nitrite exposure (50% and 30% in presence and absence of ammonium respectively). Presence of oxygen during nitrite incubation led to a maximum activity reduction of 32%. The recovery after exposure indicates that the adverse effect of nitrite is reversible and thus inhibitory rather than toxic in nature. Similarities between exposure at three different pH-values indicate that nitrite rather than nitrous acid is the actual inhibiting compound.

Membrane filtration and sonication for industrial wastewater reuse.

This paper presents an experimental study aimed at estimating the efficiency of the innovative process of ultrafiltration (UF) combined with sonication (Son.) for the refinement of treated effluent to be reused in wet textile processes. Such a novel approach, which has not yet been employed on a full industrial scale, has been experienced at pilot scale on the secondary effluent of the Baciacavallo wastewater treatment plant (WWTP), which treats part of the effluent from one of the largest textile industry districts in Italy. The combined treatment efficiency was assessed both on ozonated and non-ozonated Baciacavallo secondary effluent. The membrane filtration process was optimized in terms of running time, backwash, chemical addition and cleaning procedures. The sonication treatment was optimized on laboratory-scale with synthetic solutions (demineralized water added with dyestuffs) in terms of hydroxyl radicals formation rate, frequency, acoustic power, hydrogen peroxide addition, contact time and pH. The optimal conditions have been applied on the pilot-scale sonicator which was used in combination with the UF treatment. According to the experimental results, the best configuration within the Baciacavallo WWTP was the sonication of non-ozonated wastewater followed by the UF. The combined treatment guaranteed the compliance with the target values for wastewater reuse in wet textile industries. This study is part of the Research Project PURIFAST (Purification of industrial and mixed wastewater by combined membrane filtration and sonochemical technologies) LIFE + ENV/IT/000439.

Kinetic parameters and inhibition response of ammonia- and nitrite-oxidizing bacteria in membrane bioreactors and conventional activated sludge processes.

Ammonium and nitrite oxidizing biomasses (AOB and NOB) were investigated in parallel pilot plants: a membrane bioreactor (MBR) and a conventional activated sludge process (CASP) fed with domestic wastewater. The kinetics of AOB and NOB were monitored through titrimetric tests. The maximum specific growth rate of the AOB (micro(max,AOB)) was affected by the solids' retention time (SRT) maintained during the start up: by varying the start up SRT from 20 d to 8 d, micro(max,AOB) in the CASP varied from 0.45 d(-1) +/- 0.04 to 0.72 d(-1) +/- 0.2 respectively; the mean value of micro(max,AOB) in the MBR samples (always maintained at SRT = 20 d) was in the range 0.45-0.49 d(-1). The endogenous decay coefficients of the NOB and AOB and the maximum specific growth rates of the NOB were similar in both MBR and CASP. Inhibition tests with different concentrations of allylthiourea (ATU) were carried out on samples from both activated sludge systems: the MBR sludge exhibited higher sensitivity to a low ATU concentration; however, the maximum nitrification activity recovered more rapidly than the CASP sludge.

Microcalorimetric and manometric tests to assess anammox activity.

The present study compares two experimental methods to evaluate Anammox activity based on the assessment of (1) the N(2) production rate by a manometric device, as previously proposed, and (2) the heat production rate by a microcalorimeter. Two samples of Anammox suspended biomass were taken from a pilot-plant, and their specific Anammox activity measured by both techniques. Both methods were successfully applied. As for calorimetric tests, they were performed for the first time on Anammox enriched sludge samples. Comparisons between the specific Anammox activities estimated by manometry and calorimetry and between expected (from the reaction enthalpy) and measured heat productions were performed. Promising results were obtained.

A modified Activated Sludge Model to estimate solids production at low and high solids retention time.

In this paper, a modified version of the IWA-ASM1 model capable of correctly simulating the production of solids over a wide range of solids retention time (SRT) is presented. The parameters of the modified model have been estimated by integrating the results of respirometric and titrimetric tests with those of studies conducted on pilot scale plants that treat industrial wastewaters of differing characteristics. On the basis of the experimental results and their subsequent processing, it appears that the production of solids may be satisfactorily estimated using the modified model in which fractions X(P) and X(I) are supposed to be hydrolysable with a first-order kinetic. In the cases that were examined, the constant of the aforementioned kinetics was estimated to be k(i)=0.012 d(-1) and k(i)=0.014 d(-1), for tannery and textile wastewater respectively. A reliable calibration of the parameter k(i) was possible when data relative to the experiment conducted in the pilot plants for no less than 60 d and in conditions of complete solid retention was utilized.

Temperature modelling and prediction for activated sludge systems.

Temperature is an important factor affecting biomass activity, which is critical to maintain efficient biological wastewater treatment, and also physiochemical properties of mixed liquor as dissolved oxygen saturation and settling velocity. Controlling temperature is not normally possible for treatment systems but incorporating factors impacting temperature in the design process, such as aeration system, surface to volume ratio, and tank geometry can reduce the range of temperature extremes and improve the overall process performance. Determining how much these design or up-grade options affect the tank temperature requires a temperature model that can be used with existing design methodologies. This paper presents a new steady state temperature model developed by incorporating the best aspects of previously published models, introducing new functions for selected heat exchange paths and improving the method for predicting the effects of covering aeration tanks. Numerical improvements with embedded reference data provide simpler formulation, faster execution, easier sensitivity analyses, using an ordinary spreadsheet. The paper presents several cases to validate the model.

The role of tannins in conventional and membrane treatment of tannery wastewater.

The role that tannins play in tannery wastewater treatment has been evaluated employing a pilot Membrane Bioreactor (MBR) plant and a full scale Conventional Activated Sludge Process (CASP) plant conducted in parallel. The proposed methodology has established the preliminary use of respirometry to examine the biodegradability of a selection of commercial products (synthetic and natural tannins); the subsequent analysis, by means of spectrophotometric reading and RP-IPC (Reverse-Phase Ion-Pair) liquid chromatography, estimates the concentrations of natural tannins and naphthalenesulfonic tanning agents in the influent and effluent samples. The results show that a consistent percentage of the Total Organic Carbon (TOC) in the effluent of the biological phase of the plants is attributable to the presence of natural and synthetic (Sulfonated Naphthalene-Formaldehyde Condensates, SNFC) tannins (17% and 14% respectively). The titrimetric tests that were aimed at evaluating the levels of inhibition on the nitrifying biomass samples did not allow a direct inhibiting effect to be associated with the concentration levels of the tannin in the effluent. Nonetheless, the reduced specific growth rates of ammonium and nitrite oxidising bacteria imply that a strong environmental pressure is present, if not necessarily due to the concentration of tannins, due to the wastewater as a whole. The differences that have emerged by comparing the two technologies (CASP and MBR), in regards to the role that tannins play in terms of biodegradability, did not appear to be significant.

A simple method to evaluate the short-term biogas yield in anaerobic codigestion of WAS and organic wastes.

The present study was aimed at setting and applying a procedure to measure the anaerobic degradability of different organic substrates by short-term tests (2-7 days) carried out at lab-scale with a low food to biomass (F/M) ratio. All tests were carried out using an acclimated sludge taken from a pilot-plant anaerobic digester (200 L). Trials were performed with a manometric system. The experimental reliability of the device in measuring the anaerobic degradability was assessed by several preliminary tests carried out using acetate and glucose as reference substrates. The average conversion to methane was 99% for acetate and of 83% for glucose. The results of tests in triplicate showed the high repeatability of the method with an average coefficient of variation lower than 2%. Then, the lab-scale procedure was applied to study the short-term anaerobic degradability of complex organic substrates: thickened waste activated sludge, two kinds of organic fraction of municipal solid waste (a kitchen waste and a fruit and vegetable waste collected at the wholesale market of Florence), olive mill wastewater and freshly harvested grass. Results indicated that organic fraction of municipal solid waste, olive mill wastewater and grass were characterized by a much higher anaerobic degradability if compared to the thickened activated sludge, well in agreement with literature data.

An integrated approach in a municipal WWTP: anaerobic codigestion of sludge with organic waste and nutrient removal from supernatant.

Co-digestion appears to be an interesting solution to increase the biogas production of poorly performing under-loaded digesters of waste activated sludge. In the Florence WWTP anaerobic codigestion could increase nitrogen and phosphorus loading rates and thus lower the nutrient removal efficiency. In order to develop an integrated solution to upgrade the Florence WWTP, the different process units were tested in experimental plants. Anaerobic codigestion with source-collected organic solid waste in a pilot-scale bioreactor showed an increase of GPR from 0.15 to 0.45 Nl biogas/l/d with 23% of organic waste loaded. Autotrophic nitrogen removal was carried out in two lab-scale pilot plants which were fed with a real anaerobic supernatant after phosphate removal via struvite formation. The nitritation MBBR has been working for one year at steady-state conditions with a perfect nitrite/ammonium ratio equal to 1:1. Anammox biomass enrichment was performed in a suspended biomass SBR and the specific nitrogen removal rate increased from 1.7 to 58 gN/kgVSS/d in 375 days.

Characterization of tannery wastewater and biomass in a membrane bioreactor using respirometric analysis.

Respirometric techniques and an activated sludge model (ASM) were applied for the characterization of tannery wastewater and biomass in a pilot plant membrane bioreactor (MBR) operating at high sludge age. The traditional respirometric tests and the IWA-ASM1 were modified to take into account the specific operating conditions, the solid-liquid separation technology and the wastewater complexity. As a result the wastewater biodegradable COD was fractionated into four components: readily biodegradable, rapidly hydrolysable, slowly hydrolysable and inorganic (due to the presence of reduced sulphur compounds). The kinetic and stoichiometric parameters of the biomass (heterotrophic and nitrifying) were estimated through the integration of model simulations and respirometric tests results. In particular the ammonium and nitrite-oxidizing biomasses were separately characterized: the growth kinetics of ammonium and nitrite-oxidizing bacteria resulted noticeably lower than the traditional reference values (mu(max,AOB)=0.25d(-1)e mu(max,NOB)=0.23d(-1) at 20 degrees C, respectively). The ASM was finally used to confirm that the results of the wastewater and biomass characterization allow to properly simulate the mixed liquor suspended solids in the MBR pilot plant and the COD concentration in the effluent.

Reuse of industrial wastewater for the irrigation of ornamental plants.

This paper describes the results of experimental activities carried out for verifying the possibility of reusing reclaimed wastewater originated from textile (70%) and domestic (30%) activities for the irrigation of container-grown ornamental shrubs. Aspects that concern the refinery treatment of reclaimed wastewater and the effect of irrigation on some ornamental plant species were investigated. An experimental site consisting of a refinery treatment pilot plant (filtration and disinfection) and an agronomic experimental area was set-up. The combined treatment of PAA and UV, used for the disinfection, showed to be very effective for inactivation of E. coli with most of PAA and UV dose combinations able to assure total inactivation. The plants (Buxus, Photinia, Pistacia and Viburnum), sprinkle and drip irrigated with well water (WW), reclaimed wastewater (RW) and a water mixed (MW) between reclaimed wastewater and well water (1:1 by vol), showed interesting results. A similar growth among different treatments was achieved for Buxus and Pistacia, while Viburnum and Photinia plants showed a higher sensibility to MW and RW. Photinia, in particular, turned out to be very sensitive to sprinkle irrigation with the reclaimed water, while the drip irrigation had no such bad effects, as reported in previous works.

Effects of pre-treatment with magnetic ion exchange resins on coagulation/flocculation process.

A new Magnetic Ion EXchange resin for DOC (Dissolved Organic Carbon) removal (MIEX DOC Resin) has been evaluated as water pre-treatment at the Drinking Water Treatment Plant (DWTP) of Florence in order to reduce the oxidant demand and disinfection by-products (DBPs) formation potential. This pre-treatment leads to several effects on downstream treatment processes. In this experimental study the effects of MIEX pre-treatment on clariflocculation process were evaluated with respect to coagulant demand reduction and characteristics of flocs formed. The analysis was conducted using traditional jar test procedures and a Photometric Dispersion Analyser (PDA2000) which provided continuous information about the aggregation state of particles during the jar tests. For a fixed turbidity goal in clarified water, ion exchange pre-treatment led to coagulant dosage reduction up to 60% and PDA results shown that flocs formed in pre-treated water were bigger and more resistant to shearing effects than those formed by conventional clariflocculation.

Olive mill wastewater biological treatment by fungi biomass.

Olive oil extraction is one of the most important traditional food industries in the Mediterranean region, especially in Italy. In addition to olive oil, this industry produces by-products, in particular olive mill wastewaters (OMWs) and olive husks, which represent a serious environmental problem. OMWs can be rarely treated in a municipal WWTP, using conventional wastewater treatments. A novel biological process has to be considered in order to treat OMWs. Literature data show that yeasts and different kinds of fungi are able to reduce both the organic and the phenolic content of the OMW. The present work is aimed at investigating the growth of a biomass rich in fungi in a batch reactor filled with OMW and its capacity to degrade the organic and phenolic load. The aerobic OMW degradation obtained using this biomass reached a COD and TP removal efficiency of 86 and 70%, respectively. Respirometric tests have been carried out in order to measure the biomass activity on different substrates: OMW and phenolic compounds (gallic and p-coumaric acids). The polyphenolic biodegradation efficiency of fungi biomass was higher than the one of a non-acclimated activated sludge biomass. Fungi biomass was able to completely degrade pure phenolic compounds.

Oxidative processes for olive mill wastewater treatment.

The present work describes an experimental study carried out in order to investigate the efficiency and feasibility of physical (lime coagulation) and advanced oxidation processes (Ozone and Fenton's process) for olive oil mill wastewater treatment. Particular attention was paid to the degradation of both organic and phenolic compounds. Lime coagulation reaches maximum removal at a pH of 12, with a TP (total polyphenols) and COD reduction of 37 and 26%, respectively. Ozone oxidation is also pH-dependent, showing the higher removal efficiency (91% for TP and 19% for COD) with an initial pH value of 12. Experimental results show a lower efficiency of Fenton's process than ozone in TP removal, reaching a maximum value of 60%. Oxidation trials carried out on gallic and p-coumaric synthetic solutions confirmed ozone and Fenton's efficiency at degrading phenolic compounds. Biological trials, both aerobic and anaerobic, highlighted a significant increase of biodegradability of treated OMW samples if compared to the untreated ones. Respirometric tests showed an increase in BOD of about 20% and anaerobic batch tests provided a methane production up to eight times higher.

MBR pilot plant for textile wastewater treatment and reuse.

An experimental study was carried out in order to evaluate the possibility of upgrading the conventional activated sludge WWTP of Seano (Prato, Italy) which treats municipal and textile wastewaters, by using membrane bioreactor (MBR) technology. The MBR pilot plant, set up within Seano WWTP, was fed with mixed municipal-industrial wastewaters during the first experimental period and with pure industrial wastewaters during the second. Performances and operation of the MBR were evaluated in terms of permeate characteristics and variability (COD, colour, surfactants, total N and P) and other operational parameters (sludge growth and observed yield). According to the experimental results the MBR permeate quality was always superior to the Seano WWTP one and it was suitable for industrial reuse in the textile district of the Prato area. Respirometric tests provided a modified IWA ASM1 model which fits very well the experimental data and can be used for the design and the monitoring of a full-scale MBR pilot plant.

Olive mill wastewater treatment: an experimental study.

Olive oil production, one of the main agro-industries in Mediterranean countries, generates significant amounts of olive mill wastewaters (OMWs), which represent a serious environmental problem, because of their high organic load, the acidic pH and the presence of recalcitrant and toxic substances such as phenolic and lipidic compounds (up to several grams per litre). In Italy, traditional disposal on the soil is the most common way to discharge OMWs. This work is aimed at investigating the efficiency and feasibility of AOPs and biological processes for OMW treatment. Trials have been carried out on wastewaters taken from one of the largest three-phase mills of Italy, located in Quarrata (Tuscany), as well as on synthetic solutions. Ozone and Fenton's reagents applied both on OMWs and on phenolic synthetic solutions guaranteed polyphenol removal efficiency up to 95%. Aerobic biological treatment was performed in a batch reactor filled with raw OMWs (pH = 4.5, T = 30 degrees C) without biomass inoculum. A biomass rich of fungi, developed after about 30 days, was able to biodegrade phenolic compounds reaching a removal efficiency of 70%. Pretreatment of OMWs by means of oxidation increased their biological treatability.